Philips SLV5400 Bedienungsanleitung
Wireless TV Link
User Manual
SLV5400
G2525
2525
24
A
BC
WIRELESS TV LINK RECEIVER
IR
16
17
19
7
12131415
8
18
20
9
21
11
3 5 64
21
22
23
10
3
EN
Contents
Page
Overview 4
Control and display elements 4
Your Wireless TV Link 5
Safety 5
Installation 6
Operation 7
Enjoy your Wireless TV Link 7
Use additional features 9
Troubleshooting 10
Information 12
Health and safety 12
Maintenance and service 12
Recycling and disposal 12
Warranty 13
Glossary 13
4
EN Overview
Control and display elements
A Transmitter
1 On/off switch
2 Power light:
> red: standby
> green: on
> blinking: remote control signalling
3 RECORD SOURCE button
4 Link source indication lights
5 TV1 SOURCE button
6 AUTO light
7 Integrated remote control blaster light
8 TV1 source indication display
9 Antenna
10 SCART ports:
> 1-SAT/STB
> 2-AUX
> 3-DVD (for RGB signals)
> 4-VCR/DVD recorder (for RGB signals)
11 Wireless channel selection switch
12 Power input connector (DC 12V)
13 AUDIO OUT connectors (red/white)
14 SCART port for TV1
15 Remote control blaster cord port
B Receiver
16 On/off switch
17 Power light
> red: standby
> green: on
> blinking: remote control signalling
18 Source selector buttons (+/-)
19 Integrated remote control blaster light
20 Antenna
21 Wireless channel selection switch
22 SCART port for TV2
23 Power input connector (DC 12V)
C Remote control
G Remote control blaster cord
24 Connector
25 Blaster light
5
EN
Your Wireless TV Link
You can say good-bye to wires. With your Wireless TV
Link you can now wirelessly connect a second TV and
choose between four devices to watch on your second
TV.
Safety
• Read the instructions in this manual carefully before
you connect, install and use the product.
• Keep this manual for future reference.
• The product is for indoor use only.
• Do not use the product close to water.
• Do not expose the product to extreme heat.
• In case of technical difficulties, do not open the
product. Bring it to your Philips dealer.
• Do not cover the product.
• Connect the power adapters only to a
220-240 V AC/50 Hz power supply.
• The product can cause interference to other
equipment. Check if any equipment near the product
can be affected before you start using it.
6
EN Installation
Install the remote control blaster cord
1 Switch off the transmitter (A).
2 Connect the remote control blaster cord (G) to the
IR port.
3 Position the blaster light in front of the video source.
4 Switch on the transmitter (A).
5 Take the remote control of a video source with you.
6 Go to TV2.
7 Switch on TV2.
8 Switch on the receiver (B).
9 Select the correct SCART input on TV2.
10 Operate the video source with its remote control.
11 If necessary, repeat the steps 3 to 10 for the other
video sources.
For basic installation, see
the quick start guide that
came with your Wireless
TV Link.
STANDBY SELECT
SLV5400WIRELESS TV LINK TRANSMITTER
IR
See the user manual of the video source
for the exact location of the IR sensor
on the front panel.
STANDBY SELECT
SLV5400WIRELESS TV LINK TRANSMITTER
WIRELESS TV LINK RECEIVER
7
EN
Installation
Remove interference on TV2
1 Find the CHANNEL switch on the transmitter (A).
2 Set the CHANNEL switch to different number.
3 Find the CHANNEL switch on the receiver (B).
4 Set the CHANNEL switch to the same number as
on the transmitter.
Operation
Enjoy your Wireless TV Link
Watch a cable TV program on TV2
1 Switch on the transmitter (A).
2 Switch on the VCR or DVD recorder.
3 Take the remote control of the VCR or DVD
recorder with you.
4 Go to TV2.
5 Switch on TV2.
6 Switch on the receiver (B).
L
Channel
DC 12V
1 2 3 4
R
CHANNEL
1
2
3
4
For basic operation, see
the quick start guide that
came with your Wireless
TV Link.
Your VCR or DVD recorder needs to
be connected to the transmitter (A) of
the Wireless TV Link and connected to
the Cable-TV signal.
STANDBY SELECT
SLV5400WIRELESS TV LINK TRANSMITTER
WIRELESS TV LINK RECEIVER
8
EN Operation
7 Press +or -on the receiver (B) to select the VCR or
DVD recorder;
or: press 4on the remote control (C).
8 Select the channel on the VCR or DVD recorder
with its remote control.
Watch a video source on TV1
Either: automatic
Operate TV1 and the video source as usual.
Or: manual
1 Switch on the transmitter (A).
2 Switch on TV1.
3 Select the correct SCART input on TV1.
4 Select the video source with TV1 SOURCE;
or: press +or -on the remote control (C).
5 Switch on the video source.
6 Operate the video source with its remote control.
Turn off the auto standby mode when
you use the VCR or DVD recorder to
watch a cable tv program. Refer to the
user manual of the VCR or DVD
recorder.
If the VCR or DVD recorder records a
television program, you watch the
recorded channel.
STANDBY SELECT
SLV5400WIRELESS TV LINK TRANSMITTER
TV1 SOURCE
9
EN
Operation
Use additional features
Use VCR/DVD recorder features
1 Select a video source with SELECT.
> The signal of the video source is connected to the
VCR/DVD recorder.
2 Select the correct SCART input on the VCR or
DVD recorder.
3 Push RECORD on the VCR or DVD recorder.
4 Push PLAY on the video source.
> The VCR or DVD recorder now records the image of
the video source.
Sound through your audio amplifier
1 Take an audio cable (red and white plugs).
2 Plug the connectors of one end into the AUDIO
OUT connectors on the transmitter (A).
3 Plug the connectors of the other end into the
AUDIO IN connectors of your amplifier.
The making of unauthorised copies of copy-protected
material, including computer programmes, files,
broadcasts and sound recordings, may be an
infringement of copyrights and constitute a criminal
offence. This equipment should not be used for such
purposes.
SELECT SAT/STB
CONNECT 4-VCR/DVD RECORDER
AUX DVD PLAYER
123
TV1
AUDIO
OUT
L
R
Audio
Amplifier
Be responsible
Respect copyrights
10
EN Troubleshooting
Problem Tip
No image or wrong
image on TV1 •
Make sure video sources are
connected to the transmitter (A).
• Make sure the transmitter (A) is
connected to TV1.
• Make sure SCART cables are
firmly inserted.
• Make sure the video source is
switched on.
• Make sure the correct SCART
input on TV1 is selected.
• Select the correct video source
with TV1 source. See page 8.
No image or wrong
image on TV2 • Make sure SCART cables are
firmly inserted.
• Make sure the receiver (B) is
connected to TV2.
• Make sure both receiver (B) and
transmitter (A) are switched on.
• Make sure the video source is
switched on.
• Make sure the correct SCART
input on TV2 is selected.
• Select the correct video source
with +/- on the receiver (B).
• If the video source gives proper
image on TV1:
Make sure the video source gives
video signal in CVBS mode. See
its user manual
• Change the wireless channel that
is used for communication. See
page 7.
• The receiver (B) is out of range
of the transmitter (A). The num-
ber of walls and ceilings in
between the receiver (B) and
transmitter (A) restrict the dis-
tance.
Andere Handbücher für SLV5400
1
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Philips Empfänger Handbücher
Philips
Philips 90RL412 Bedienungsanleitung
Philips
Philips DTR4610 Bedienungsanleitung
Philips
Philips DTR 2010 Bedienungsanleitung
Philips
Philips DTP4800 Bedienungsanleitung
Philips
Philips DRE420SY Bedienungsanleitung
Philips
Philips MX3900D Bedienungsanleitung
Philips
Philips FR740 Bedienungsanleitung
Philips
Philips HTR5205 Bedienungsanleitung
Philips
Philips MRD300/37/78 Bedienungsanleitung
Philips
Philips DSX6073/03A Bedienungsanleitung
Philips
Philips DSR 1000 Bedienungsanleitung
Philips
Philips FR732/00 Bedienungsanleitung
Philips
Philips HTS3100 Series Bedienungsanleitung
Philips
Philips DSX 5350 Bedienungsanleitung
Philips
Philips HTS3440/37 Bedienungsanleitung
Philips
Philips MRD210/37 Bedienungsanleitung
Philips
Philips MX5800SA Bedienungsanleitung
Philips
Philips LX 3700D Bedienungsanleitung
Philips
Philips FR735 Bedienungsanleitung
Philips
Philips Digital Cable Receiver DCR2022 Bedienungsanleitung
