Philips KWR174002/01BRS Bedienungsanleitung

Philips Home Control

Confidential Philips Home Control,

2014

Page 1 of 11

Manual of

KWR174002/01BR,

KWR174002/01BRS,

KWR174002/01BRU

KWR174003/01BR,

KWR174003/01BRS &

KWR174003/01BRU

Philips Home Control

Confidential Philips Home Control,

2014

Page 2 of 11

FCC Statement

FCC Part 15.19

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference and

(2) this device must accept any interference received, including interference that may

cause undesired operation.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

No special accessory is required to enable the equipment to comply with the emission

limits.

RF exposure warning

The equipment complies with FCC RF exposure limits set forth for an uncontrolled

environment.

The equipment must not be co-located or operating in conjunction with any other

antenna or transmitter.

KWR174002/01BR &

KWR174003/01BR

Manual (Draft Version)

Status :Draft, For Review Page 3 of 11

Philips Proprietary &Confidential

Philips Home Control Company Restricted

1. Product Description

1.1 Product Features

Dual button entry RC and KWR.

Number of keys: 42 for Keyboard, 40 for RC.

4 main functions. Remote control, mouse cursor control and QWERTY KB for text entry and

downstream data transfer.

3-D Gyro meter for motion pointing.

Infrared (IR).

Low voltage alert through LED blinks.

Compatible with USB RF4CE Receiver dongle for the RF portion.

KWR174002/01BR &

KWR174003/01BR

Manual (Draft Version)

Status :Draft, For Review Page 4 of 11

Philips Proprietary &Confidential

Philips Home Control Company Restricted

Product

Picture for illustration onl

KWR174002/01BR &

KWR174003/01BR

Manual (Draft Version)

Status :Draft, For Review Page 5 of 11

Philips Proprietary &Confidential

Philips Home Control Company Restricted

2. RF Functions

2.1 RF Pairing

1) Make sure RC is within 1m distance from the STB and no other RF RCs are present.

2) Make sure the Qwerty keyboard faces upwards.

3) Press and hold Keyboard W and Keyboard O keys together for at least 5 seconds.

4) The KEYBOARD LED will start blinking, and RC is now in pairing mode.

5) Activate pairing mode on STB (STB sends activate command or reset dongle power).

6) Once the pairing is successful, the KEYBOARD LED will be turned off; otherwise, the KEYBOARD

LED will stay lit till timeout.

There will be a 30 seconds timeout for RC to be in pairing mode. Previously paired receiver shall be

retained as long as the STB did not initiate the pairing. See Note below on different pairing scenarios.

User can start from Step 1 again if pairing failed.

Note:

When a previously paired RC starts pairing with

1. Different receiver

o Only upon successful pairing, the RC shall replace the previously paired receiver with the new

receiver.

o If the pairing process fails or pairing timeout occurs, the previously paired receiver will be retained.

2. Same receiver

o Previously paired information of the same receiver shall first be erased from the RC before pairing

process starts.

o If the pairing process fails or pairing timeout occurs, the previously paired receiver will not be

retained.

At any one time,

 Only one RC is allowed to be in pairing mode, i.e. no concurrent pairing is allowed.

 Each RC can only work with one receiver, i.e. 1-to-1 pairing.

2.2 RF Un-Pairing

The following steps for un-pairing:

1) Make sure the Qwerty keyboard faces upwards.

2) Press and hold Keyboard X and Keyboard UP keys together for at least 5 seconds.

3) The KEYBOARD LED will start blinking slowly after 5 seconds.

4) Reset the power or battery and the RC is ready to pair again.

2.3 Remote Idling, RF Link Timeout with connection

When detected no activity, the RC will enter SLEEP mode. During SLEEP mode, RF link will be

disconnected to preserve power. Pressing any key or any gesture action will resume the RC to

ACTIVE mode almost immediately. The key-press that resumes the RC from SLEEP mode will be

remembered and transmitted.

When the RC wakes up from SLEEP mode, there may be reconnection latency depending on the RF

link condition with the receivers.

Once the RF (2.4G) link has been established, the RC will execute upon ANY key-press. Key presses

prior to successful RF link connection will not be transmitted.

KWR174002/01BR &

KWR174003/01BR

Manual (Draft Version)

Status :Draft, For Review Page 6 of 11

Philips Proprietary &Confidential

Philips Home Control Company Restricted

2.4 RF Broken Link

RF link is broken when the RF (2.4G) connection is lost or when the receivers sleep or during system

shutdown states (S3, S4 or S5) or due to out-of-range.

2.5 RF ACTIVE / SLEEP

From RF ACTIVE >> SLEEP User action Remote Control action

No key-press for about 8 seconds. RF goes to SLEEP. In SLEEP mode, all LEDs are OFF.

No motion senses for about 8 seconds. RF goes to SLEEP. In SLEEP mode, all LEDs are OFF.

2.6 RF Auto Connection

When the RC wakes up or resumes from SLEEP mode or come back within range of a powered-on

paired receiver, the RF link will be reconnected automatically. No RF re-pairing is needed.

2.7 RF Out-of-Range

When the RF link is broken or out-of-range and is stationary, the RC goes to SLEEP immediately to

conserve power.

KWR174002/01BR &

KWR174003/01BR

Manual (Draft Version)

Status :Draft, For Review Page 7 of 11

Philips Proprietary &Confidential

Philips Home Control Company Restricted

3. Operational Features

3.1 Mode Switch

3.1.1 RC to Keyboard

When in RC mode, KEYBOARD keys will be locked to prevent accidental presses. KEYBOARD keys

can only be unlocked by tilting 90 degrees clockwise or anticlockwise. Once tilted more than 90

degrees, mouse cursor will stop moving if it is in Mouse mode.

If KEYBOARD keys are faced up upon power up, a command will be sent from the RC.

3.1.2 Keyboard to RC

When in KEYBOARD mode, user can change to RC mode by tilting 90 degrees clockwise or

anticlockwise. When in KEYBOARD mode, RC keys will be locked to prevent accidental presses.

Once tilted more than 90 degrees, mouse cursor will start moving if it is in Mouse mode.

If RC keys are faced up upon power up, a command will be sent from the RC.

3.2 Remote IR Keys

STANDBY is the only IR command key. With RC faced up and in a portrait orientation, pressing this

button will fire the respective IR codes from the IR LED of the remote.

3.3 Remote RF keys

Remote RF keys will be sent in the form of HID Keyboard keys.

3.4 Motion Control Mouse Mode

Mouse mode allows user to use the 3-D gyroscope and accelerometer of the RC as a floating mouse

or joystick. In this mode, user is also expected to operate the remote control in free air and not laid

down and operating it in a stationary position.

The relative movement of panning and lifting (roll, yaw and pitch) will control the mouse cursor to

move in the same relative direction on the screen.

For mouse cursor control, toggle motion sensor ON:

- Move remote control in the air to use motion mouse control

- Press OK key will be Mouse Left Click function only, press and hold Mouse Left Click is supported

- Provides RAW data for gesture processing, enable/disable with downstream command from host.

KWR174002/01BR &

KWR174003/01BR

Manual (Draft Version)

Status :Draft, For Review Page 8 of 11

Philips Proprietary &Confidential

Philips Home Control Company Restricted

3.5 Keyboard Mode

The Qwerty keyboard will be held by both hands and used in landscape orientation.

The keyboard also supports secondary keys by using FN or SHIFT; this allows the keyboard to

support uppercase characters, symbols and digits with the limited number of Qwerty keys.

There are 2 ways of activating secondary keys:

1. Press and release FN or SHIFT key followed by pressing another key. For example, press FN then

Q will send „1‟, press SHIFT then Q will send “Q”. After “Q” is released and pressed again, „”q” will

be sent.

2. Press and hold FN or SHIFT key followed by pressing another key. For example, press and hold

FN and then press Q will send “1”, press and hold SHIFT and Q will send “Q”.

As long as the secondary key is pressed and held, the secondary character will have the same

repeating behavior as the normal primary key „press and hold‟.

To minimize accidental presses of the Qwerty keys while in RC or Mouse Cursor Control, the Qwerty

keys will be deactivated. When not in SLEEP mode and the keyboard side is detected faced down,

the Qwerty keys will be locked, key presses on the keyboard will be ignored. When device is not in

SLEEP mode and the keyboard side is detected faced up, the Qwerty keys are unlocked.

KWR174002/01BR &

KWR174003/01BR

Manual (Draft Version)

Status :Draft, For Review Page 9 of 11

Philips Proprietary &Confidential

Philips Home Control Company Restricted

3.6 LED Indicator Behaviour

Total 2 Indicator backlit LED – Red and Blue LED:

Location

Indication purpose

Status description

BLUE LED

Indicate RF code transmission

1 short blink in blue each time a valid

key is pressed

RED LED

Indicate IR code transmission

1 short blink in red each time a valid

key is pressed

RED LED

Low battery warning

2 short blinks in red each time a valid

key is pressed

BLUE LED

Mouse Left Click

1 short blink in blue each time Mouse

Left Click is pressed

Blue LED Show successful RF pairing

Flashes rapidly in blue until pairing is

successful or time out occurs

KWR174002/01BR &

KWR174003/01BR

Manual (Draft Version)

Status :Draft, For Review Page 10 of 11

Philips Proprietary &Confidential

Philips Home Control Company Restricted

4. Non-Functional Requirements

4.1 Simultaneous Key Press (RC)

If more than one key-press is detected, the remote control will stop sending IR/RF code.

Example:

i. When Key 1 is pressed, Key 1 code is transmitted. Pressing Key 2, with Key 1 still pressed, RC will

stop transmitting Key 1 code. Then, releasing Key 2, with Key 1 still pressed, Key 1 code will be

transmitted again.

ii. When Key 1 is pressed, Key 1 code is transmitted. Pressing Key 2, with Key 1 still pressed, RC will

stop transmitting Key 1 code. Then, releasing Key 1, with Key 2 still pressed, Key 2 code will be

transmitted.

4.2 Simultaneous Key Press (Keyboard)

The remote support multiple key presses but only limited keys are able to do so. When two or more

remote KB keys that do not support simultaneous press are pressed simultaneously, the remote will

not send codes. When only one key is still pressed the remote will restart and send the code of this

key as per normal.

Workable 2 keys simultaneous key presses are;

SHIFT with any Alphabets: Capital Letters of the Alphabets

FN with keys with Blue options (numbers and symbols, etc.)

4.3 Consecutive Key Press (Keyboard)

When FN key is pressed or still pressed, the RC will not transmit or do any action. After release and

then press any keys that have alternate function on the same key, e.g. Q key shares the same as

Numeric ‘1’ key, the RC will transmit Numeric ‘1’ code.

E.g. FN key + Q key = Numeric ‘1’ key transmit

FN key + A key = Symbol ‘?’ key transmit

The same is true for SHIFT keys. For SHIFT, after release of the key, an alphabet key is pressed; the

RC will transmit the capital letter of the particular key.

4.4 LED Indicator

Blinking Definition

Short Blink: Approximately 10ms ON, then OFF.

Long Blink: 500ms ON, 500ms OFF.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Philips Fernbedienung Handbücher

Philips

Philips ProntoPro Next Generation Bedienungsanleitung

Philips

Philips Pronto TSU3000 Bedienungsanleitung

Philips

Philips SBCRU125/00 Bedienungsanleitung

Philips

Philips SRP6219G/27 Bedienungsanleitung

Philips

Philips Pronto TSU 2000 Bedienungsanleitung

Philips

Philips SRP 3004/53 Bedienungsanleitung

Philips

Philips Pronto TSU3000 Bedienungsanleitung

Philips

Philips 22AV1106 Bedienungsanleitung

Philips

Philips SBC RU 760 Bedienungsanleitung

Philips

Philips SBCRU098/00 Bedienungsanleitung

Philips

Philips Trilingual Front CoverArt PH5DSS Bedienungsanleitung

Philips

Philips SRP2018 Bedienungsanleitung

Philips

Philips SBC RU 530 Bedienungsanleitung

Philips

Philips PR1906C121 Bedienungsanleitung

Philips

Philips Pronto TSU9200 Sicherheitsleitfaden

Philips

Philips SRU8008/27 Bedienungsanleitung

Philips

Philips SRU 5020/87 Bedienungsanleitung

Philips

Philips Home power SRP4419V/27 Bedienungsanleitung

Philips

Philips SBCRU440/00U Bedienungsanleitung

Philips

Philips SBCRU430/02D Bedienungsanleitung

Philips

Philips 22AV1106B Bedienungsanleitung

Philips

Philips SRU 1018 Bedienungsanleitung

Philips

Philips SBCRU240/00 Bedienungsanleitung

Philips

Philips RC1974503/00RF Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung