Philips SRU 520/86 Bedienungsanleitung

SRU 520/86

Universal

Quick, Clean & Easy Setup

www.philips.com/urc

Instructions for use 4

Mode d'emploi 11

Bedienungsanleitung 18

Gebruiksaanwijzing 25

Vejledning 32

Bruksanvisning 39

Bruksanvisning 46

Käyttöohje 53

FIN

SRU520_86_v6.qxd 26-04-2005 14:26 Pagina 1

SRU520_86_v6.qxd 26-04-2005 14:26 Pagina 2

SRU520_86_v6.qxd 26-04-2005 14:26 Pagina 3

Contents

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2. Installing the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

Inserting the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Testing the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Setting the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3. Keys and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4. Extra possibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9

Adjusting device selection (Mode keys) . . . . . . . . . . . . . . . . . . . . . . . . . 8

Adding a function to the remote control . . . . . . . . . . . . . . . . . . . . . . . . 8

Restoring the original functions of your remote control . . . . . . . . . . . . 9

5. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

6. Need help? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Code list of all brands / equipment . . . . . . . . . . . . . . . . . . . . . . . . . 60-73

1. Introduction

Congratulations on your purchase of the Philips SRU520 universal remote

control. After installing the remote control you can operate a maximum of

2 different devices with it:TV and VCR/DVD players/recorders.

You can find information about how to prepare this remote control for use in

the chapter ‘Installing the remote control’.

2. Installing the remote control

Inserting the batteries

1Press the cover inwards and slide it

in the direction of the arrow.

2Place two AAA type batteries into the

battery compartment, as shown.

3Slide the cover back and click it firmly into

place.

Note: If the

mode keys (TV and DVD/VCR)

blink four times after every key press, the

remote control is indicating that its batteries are running low. Replace the old

batteries with two new AAA batteries.

Testing the remote control

The remote control has been programmed to operate most Philips devices.

Because the SRU520 may use different signals for each brand and even for

different models of the same brand, it is advisable to test whether your

device responds to the SRU520.The example below (TV) instructs you how

to do this.You can repeat the same steps for other devices

(VCR/DVD players/recorders) which you want to operate using the SRU520.

Example of TV:

1Turn your TV on manually or use the original remote control.

Tune to channel 1.

2Press the TV key to select TV. Press the key

until it lights up.

–If the key does not light up, check whether the

batteries are properly inserted

(see ‘Inserting the batteries’).

Instructions for use

English

SRU520_86_v6.qxd 26-04-2005 14:26 Pagina 4

Instructions for use

English

3Check whether all the keys are working.

For an overview of the keys and their

functions see ‘3. Keys and functions’.

–If the TV responds as it should to all of the

key commands the SRU520 is ready for use.

•If the device does not respond at all or not to all of the

key commands, follow the instructions under

‘Setting the remote control’, or for online setup go to:

www.philips.com/urc.

Setting the remote control

This is only necessary if your device does not respond to the SRU520.

If that is the case, the SRU520 does not recognize the brand and/or model of

your device and you need to program the remote control to do so.

The example below (TV) instructs you how to do this.You can repeat the

same steps for other devices (VCR/DVD players/recorders) which you want

to operate using the SRU520.

You can set the remote control either automatically or manually.

Automatically setting the remote control

The remote control will now automatically search for the right code for your

device.

Example of TV:

1Make sure the TV is switched on and select a channel using the original

remote control or the keys on the TV (for example channel 1).

The SRU520 emits the ‘switch off TV’ signal for all models of TV that are

stored in the memory.

•If the device is a DVD-player or video recorder, insert a disk or tape

and start playback.

2Press the TV key to select TV. Press the key

until it lights up.

3Then keep keys 1 and 3 on the

SRU520 pressed simultaneously for three

seconds,until the key flashes twice and then

remains lit.

4Press and hold the Standby key

of the SRU520.

–The SRU520 now starts emitting all known

‘TV off’ signals, one by one.

Each time a code is sent, the TV key lights up.

SRU520_86_v6.qxd 26-04-2005 14:26 Pagina 5

5When your TV switches off (stand-by), release the Standby key of the

SRU520 immediately.

–The SRU520 has now found a code that works on your TV.

6Check if you can operate all functions on your TV with the SRU520.

•If this is not the case, you can redo the automatic setting.

The SRU520 will then search for a code that works better.

–After the SRU520 has run through all the known codes,

the search will stop automatically and the TV button stops flashing.

–Automatic programming of a TV takes a maximum of 5 minutes. For

VCR/DVD this time is 2 minutes.

Manually setting the remote control

Example of TV:

1Turn on the TV manually or use the original remote control.

Tune in to channel 1.

2Look up the brand of your TV in the

code list at the back of this manual. One or

more four-figure codes are shown for each

brand. Note the first code.

Be careful! There are separate tables for TV,VCR

and DVD.

On our website www.philips.com/urc you can directly select your device

typenumber to find the right code.

Make sure you use the codes from the correct table.

3Press the TV key to select TV. Press the key

until it lights up.

4Keep keys 1 and 3 pressed simultaneously

for three seconds until the TV key flashes

twice and then remains lit.

5Then enter the code noted in step 2 using the digit keys.

–The TV key will now flash twice.

If the key flashes once for an extended period, the code has not been

entered properly or the wrong code has been entered.

Start again from step 2.

6Point the SRU520 at the TV and check that it responds as it should.

–If the TV responds to all of the key commands, the SRU520 is ready for

use. Do not forget to note your code.

•If the device does not respond at all, or not to all of the

key commands, start again from step 2 and try the next code

from the list.

Instructions for use

English

SRU520_86_v6.qxd 26-04-2005 14:26 Pagina 6

3. Keys and functions

The illustration on page 3 gives an overview of all keys and their functions.

1yStandby . . . . . . . . switches TV,VCR or DVD on or off.

2. . . - teletext on/off ( );

. . . - text mix ( );

. . . - text off ( );

- wide screen TV ( );

- enlarge ( );

- text hold ( ).

3MENU . . . . . . . . . . . turns the menu on and off.

4Cursor keys . . . . . . cursor up, down, left, right in a menu.

5A/V. . . . . . . . . . . . . . . . switches between external inputs of your equipment.

6s. . . . . . . . . . . . . . . . mutes the sound of the TV.

7- VOL +. . . . . . . . . . . adjusts the TV volume.

8Digit keys . . . . . . . . direct choice of channels and other functions.

9SHIFT . . . . . . . . . . . for extra functions.When pressed at the same

time as a second key, the second key will get

another function. All blue labelled keys can be used

together with SHIFT. For example:

SHIFT + INSTALLinstalls your TV

SHIFT + STORE. . stores TV settings

Tr y out other combinations with the SHIFT-key on your device in order to

find out which functions are available.

Only functions featured on the original remote control are available.

05. . . . . . . . . . . . . . . . - red teletext key

- rewind (VCR/DVD)

2. . . . . . . . . . . . . . . . - index

- play (VCR/DVD)

6. . . . . . . . . . . . . . . . - blue teletext key

- wind (VCR/DVD)

9. . . . . . . . . . . . . . . . - green teletext key

- stop (VCR/DVD)

0. . . . . . . . . . . . . . . . record

;. . . . . . . . . . . . . . . . . - yellow teletext key

- pause (VCR/DVD)

!/. . . . . . . . . . . . . . . selects between one- and two-figure channel

numbers.

@22. . . . . . . . . . . . . . . selects previous programme/channel.

#- PROG + . . . . . . . . selects a previous or following channel.

$OK. . . . . . . . . . . . . . . confirms your selection.

%BACK. . . . . . . . . . . . jumps back one level in the menu or turns off the

menu.

^TV - DVD/VCR . . . seletcs TV or DVD/VCR mode.

If you use the (ﬁ) 'memory off' key to get to the next teletext page on your

Philips TV, you can press the STOP key for this. See also ‘Troubleshooting’.

•If the device does not respond at all, or not to all of the key

commands, follow the instructions under ‘Setting the remote

control’. It is possible that you must enter another code for the

device.

Instructions for use

English

SRU520_86_v6.qxd 26-04-2005 14:26 Pagina 7

4. Extra possibilities

Adjusting device selection (Mode keys)

The SRU520 is default set for operating TV,VCR or DVD.You can select the

device you wish to operate with TV and DVD/VCR selection buttons. Each

key allows operation of one device only. If desired, you can program the keys

to select a different kind of device.

For example, if you want to operate a second TV.

In the following example you will see how to configure the DVD/VCR key for

a second TV.

1Switch on the second TV.

2Press the DVD/VCR key to select DVD/VCR.

Press the key until the it lights up.

3Then keep keys 1 and 6 on the SRU520

pressed simultaneously for three seconds,

until the DVD/VCR key lights up.

4Press keys 9, 9 and 2, in that order.

5Press the TV key to select TV. Press the key

until it lights up.

6Press the 1 key.

–The DVD/VCR key flashes twice.

The DVD/VCR key will now allow you to

operate your second TV.

7Program the SRU520 to operate the second

TV.

See ‘Setting the remote control’.

Adding a function to the remote control

If you want to add a function to the SRU520, you can contact the

Philips service line for Universal Remote Control to ask for the 5-figure code

for the extra function.

Instructions for use

English

SRU520_86_v6.qxd 26-04-2005 14:26 Pagina 8

Restoring the original functions of your remote

control

1Keep keys 1 and 6 on the SRU520

pressed simultaneously for three seconds,

until the mode key (TV or DVD/VCR) flashes

twice and then remains lit.

2Press keys 9, 8 and 1 in that order.

– The mode key (TV or DVD/VCR) key flashes

twice. All original functions have now been

restored and any extra functions have been

deleted.

5. Troubleshooting

• Problem

– Solution

•

The mode keys

(TV and DVD/VCR)

blink four times after every key press.

–The remote control is indicating that its batteries are running low. Replace the

old batteries with two new

1.5 Volt,

AAA batteries.

•The device you want to operate does not respond and the mode key

(TV or DVD/VCR) does not flash when you press a key.

–Replace the old batteries with two new 1.5 Volt,AAA batteries.

•The device you want to operate does not respond but the mode key

(TV or DVD/VCR) does flash when a key is pressed.

–Point the SRU520 at the device and make sure that there are no

obstructions between the SRU520 and the device.

•The SRU520 does not respond properly to commands.

–Maybe you are using the wrong code.Try programming the SRU520 again

using another code, which is mentioned under the brand of your device, or

reset for automatic search to find the right code.

If the device still does not respond, call our helpline.

•The Teletext keys do not work.

– Find out whether your TV is equipped with Teletext.

•You have difficulties operating all of the functions on your device.

– Maybe the SRU520 has to be adapted to the model of the device.

Call our helpline for details.

•Your brand of device is not in the code list.

– Try to set the SRU520 automatically.

See ‘Automatically setting the remote control’.

•None of the codes works during manual setting of the remote control.

– If that is the case, follow the instructions under

‘Automatically setting the remote control’.

Instructions for use

English

SRU520_86_v6.qxd 26-04-2005 14:26 Pagina 9

6. Need help?

If you have any questions about the SRU520, you can always contact us.

You will find our contact details after the code list at the back of this manual.

Read this manual carefully before you make a call.You can solve most of the

problems yourself. If you cannot find any answers to your problems, write

down the details of your device shown in the code list at the back of this

manual.This will help our operators to assist you better and more quickly.

Look up the numbers of the models in the instructions accompanying the

device or on the back of your device.When you call our helpline, make sure

the device is to hand so that our operators can help you determine whether

your remote control is working properly.

The model number of your Philips universal remote control is

SRU520/86.

Date of purchase: ......../......../........

(day/month/year)

Instructions for use

English

SRU520_86_v6.qxd 26-04-2005 14:26 Pagina 10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Philips Fernbedienung Handbücher

Philips

Philips Pronto TSU9405 Bedienungsanleitung

Philips

Philips SRP6013 Bedienungsanleitung

Philips

Philips Perfect replacement SRC2063WM Bedienungsanleitung

Philips

Philips Environ3 61205A Bedienungsanleitung

Philips

Philips Perfect replacement SRC2063WM/17 Bedienungsanleitung

Philips

Philips SRU5130/53 Bedienungsanleitung

Philips

Philips SpeechMike Premium Touch SMP3700 Bedienungsanleitung

Philips

Philips SBCRU530/88 Bedienungsanleitung

Philips

Philips SBCRU631 Bedienungsanleitung

Philips

Philips TSU9400/93 Sicherheitsleitfaden

Philips

Philips TSU500 Bedienungsanleitung

Philips

Philips Perfect replacement SRP5107/27 Bedienungsanleitung

Philips

Philips Pronto TS1000 Bedienungsanleitung

Philips

Philips SBC RU 252/00H Bedienungsanleitung

Philips

Philips SBCRU940/00 Bedienungsanleitung

Philips

Philips Prestigo SRU8015/34 Bedienungsanleitung

Philips

Philips ProntoPro Next Generation Bedienungsanleitung

Philips

Philips SRP 3004/53 Bedienungsanleitung

Philips

Philips SRU 530/86 Bedienungsanleitung

Philips

Philips Perfect replacement SRP5107WM Bedienungsanleitung

Philips

Philips SBCRU111/00 Bedienungsanleitung

Philips

Philips SBCRU631/87 Bedienungsanleitung

Philips

Philips SBCRU510/00B Bedienungsanleitung

Philips

Philips SRU9600 Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung