Philips 20PV184 Bedienungsanleitung

The remote control

STANDBY mStandby

CLEAR Reset/clear

0-9 Digit buttons 0-9

SV/V+ ’VIDEOPlus+’ programming

TIMER kTIMER programming on the set

MENU Call menu

OK Confirm button

D/C/A/B Menu left/right/Up/Down

Sp Volume control

PpProgramme number Plus/Minus

MUTE yMute sound

GPLAY Playback

HRewind/Reverse scanning

STOP hPause/Stop

IForward wind/ Forward scanning

INDEX EIndex search

RECORD nRecord

STILL RStill picture

TRANSP. -TELETEXT transparent

TELETEXT eTELETEXT on/off

CLOCK .TELETEXT clock time

In TELETEXT you can store the relevant page with the

OK button.

Selecting TELETEXT functions: when you are in

TELETEXT, press the MENU button. Select the

required function with the Dand the Cbuttons.

Confirm with the OK button.

Front of the set

mStandby

PpProgramme number Plus/Minus

Sp Volume control

5Record

HRewind/Reverse scanning

hPause/Stop

GPlayback

IForward wind/ Forward scanning

JCassette eject

wHeadphones socket

OPERATING INSTRUCTIONS IN BRIEF

Programming with ’VIDEOPlus+’

All the information required for programming is encoded in the ’VIDEOPlus+’ code.

1Press the SV/V+ button on the remote control.

2Enter the entire ’VIDEOPlus+ code’. This code (up to 9 digits) is found next to the start time of a

TV programme in your TV guide.

If you entered an incorrect code number, clear it with the CLEAR button.

3If you want to repeat programming at daily or weekly intervals, select the required settings in

the ’DAILY/WEEKLY’ line.

’Daily’ programming can only be used for recordings to be made from Mondays to Fridays

inclusive.

4After confirming the corresponding data appears on the TV screen.

Note: If you use VIDEOPlus+ for the first time, the ’PROGRAMME NR.’ line appears when you

enter the VIDEOPlus+ code. Enter the required programme number.

5Confirm with the OK button.

The data has been stored in a TIMER block.

Please ensure that you loaded a cassette without erase protection.

6Press the STANDBY mbutton.

How to enter, check or clear a TIMER-block manually

1Press the TIMER kbutton.

2Select a free TIMER block or the TIMER block you want to check or clear.

3Clear: Press the CLEAR button.

4Enter/Check: Press the Dor Cbutton to switch between ’DATE’ (date), ’DW’ (daily, weekly),

’PR’ (programme number), ’START’ (start time) and ’END’ (end time).

Press the Aand the Bor the 0-9 buttons to change the data.

5To end programming, press the MENU button.

6Press the STANDBY mbutton.

Selecting a TV channel

Select the required TV channel (= programme number) with the Ppbutton or the 0-9 but-

tons on the remote control.

The selected programme number (e.g.: ’P 01’ ) appears in the upper right corner of the TV screen.

Volume control

You can control the volume level with the Sp button.

If you want to mute the sound temporarily (e.g.: during a telephone call), press the MUTE ybut-

ton on the remote control. When you press it again, the sound returns at the same volume level.

Picture control

You can control brightness, contrast, sharpness and colour here.

1Press the MENU button.

2Select and confirm the line ’PICTURE’ .

3Select and confirm the TV screen setting.

Note: In addition, you can adjust the tint for the playback of cassettes in the NTSC standard.

Congratulations on the purchase of one of the most

sophisticated and simple-to-use television/video recorder

combinations (TV Combi) on the market. With this TV Combi

you can record and play VHS-standard cassettes.

Please take the time to read this operating manual before

using your TV Combi.

Safety instructions and other notes

•Danger: high voltage! Do not open the set. The set does not

contain any components that can be repaired by the customer.

When the appliance is connected to the power supply there are

some components that are constantly operational. To switch off

the set completely you must disconnect it from the power supply.

•Note that this power pack is designed for a power supply of

220-240V/50Hz.

•Ensure that air can circulate freely through the ventilation slots

on the set.

•Ensure that no objects or liquids enter the set. If liquid is spilt into

it, disconnect the set immediately from the power supply and call

the After-sales Service for advice.

•The set should not be used immediately after transportation from

a cold to a hot area or vice versa, or in conditions of extreme

humidity.

After unpacking the set, it should be allowed to acclimatize for at

least three hours before installation.

•These operating instructions have been printed on nonpolluting

paper.

•Deposit old batteries at the relevant collection points.

•Please make use of the facilities available in your country for

disposing of the packaging of the set in a way that helps to

protect the environment.

•This electronic equipment contains many materials that can be

recycled. Please inquire about the possibilities for recycling your

old set.

•VIDEOPlus+ and PlusCode are trademarks of Gemstar Develop-

ment Corpoation. The VIDEOPlus+ system is manufactured under

licence from Gemstar Development Corporation.

Contents Page

1. INSTALLATION 2...................................

Connecting additional equipment 3...................

Emergency interrupt 3...............................

User guide 3.......................................

Making standard settings 3..........................

Setting the clock and date 3..........................

2. PLAYBACK 5.......................................

Continuous playback 5..............................

3. RECORD 6.........................................

Programming with ’VIDEOPlus+’ 7....................

4. SPECIAL FEATURES 8...............................

On Screen Display (OSD) 8...........................

Sleep function (switch off) 8.........................

Switch set on function 9.............................

Child lock 9........................................

Before you call an engineer 10.......................

OPERATING INSTRUCTIONS PHILIPS 20PV184/05

Important for the United Kingdom

This apparatus is fitted with an approved moulded 13 Amp

plug. To change a fuse in this type of plug proceed as follows:

1Remove fuse cover and fuse.

2Fix new fuse which should be a BS1362 5A, A.S.T.A. or BSI

approved type.

3Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should

be cut off and an appropriate plug fitted in its place.

If the mains plug contains a fuse, this should have a value of

5A. If a plug without a fuse is used, the fuse at the distribution

board should not be greater than 5A.

Note: * The severed plug must be destroyed to avoid a

possible shock hazard should it be inserted into a 13A

socket elsewhere.

How to connect a plug:

The wires in the mains lead are coloured in accordance with

the following code:

BLUE - ’NEUTRAL’ (’N’)

BROWN - ’LIVE’ (’L’)

1The BLUE wire must be connected to the terminal which is

marked with the letter ’N’ or coloured BLACK.

2The BROWN wire must be connected to the terminal

which is marked with the letter ’L’ or coloured RED.

3Do not connect either wires to the earth terminal in the

plug which is marked with the letter ’E’ or by the safety

earth symbol \or coloured green or green-and-

yellow.

Before replacing the plug cover, make certain that the cord

grip is clamped over the sheath of the lead - not simply over

the two wires.

Connecting the cables

1Insert the aerial plug into the 2socket.

2Insert the plug of the mains cable into the wall socket.

3Switch the set on. The power switch 8is located on

the left side panel of the set.

Important notes for operation

•We advise you, from now on, to switch the set to standby

using the STANDBY mbutton on the front of the set or on

the remote control.

•When the set is in the standby mode, a small red lamp on

the left of the front of the set will be alight.

•You can switch on with the STOP hbutton, the

0-9 buttons or by inserting a cassette.

•Attention: When you use the power switch 8on the

side panel, you have completely switched off the set from

the mains power supply. No programmed recordings will

then be made. The red lamp on the left of the front of the

set will not be alight. After a few hours, the date and clock

settings will be lost.

•Attention: Before you switch off the appliance with the

power switch 8, remove the tape by pressing the

Jbutton.

•Keep your TV Combi connected to the mains and the

power switch in ’on’ position at all times to ensure that

programmed recordings can be made and that the

television functions normally. The power consumption

required is low.

•Back-up power supply: TV channel storage - typically 1

year, Clock/Timer - typically 30 hours.

1. INSTALLATION

Connecting additional equipment

You can also connect additional equipment to the EXTERNAL

socket, for instance, a decoder satellite receiver or camcor-

der.

Emergency interrupt

Both the set and the remote control have an ’Emergency

interrupt’ button. You can use the STANDBY mbutton to in-

terrupt any function.

To interrupt a TIMER recording, press the STANDBY mbut-

ton several seconds.

Whenever you have operating problems you can simply

interrupt the function and start again.

You can practise operating your set without any worries. No

matter which buttons you press, you cannot damage it.

User guide

With OSD (On Screen Display) the corresponding functions

appear on the TV-screen. The most important button-functions

are displayed at the bottom of the screen.

Throughout this instruction manual, use the following buttons

for the functions ’Call up’, ’Select’, ’Enter’/’Adjust’, ’Confirm’

and ’Exit’:

•Call up: Use the MENU button.

•Select: Select a line with the Aor Bbutton.

Use the 0-9 buttons or the Dor Cmenu but-

ton to select within a line.

•Enter/Alter: With the Dor Cor with the 0-9

button.

•Confirm: With the OK button.

•Exit: With the MENU .

Making standard settings

1To start, press the STOP hbutton. Press the menu

buttons Dand Csimultaneously.

INSTALLATION vw

LANGUAGE EN

COUNTRY GB

AUTO STORE

MANUAL STORE

SORT

PP STORE

2Select the required display language in the ’LANGUAGE’

line.

3Select your country in the ’COUNTRY’ line.

Setting the clock and date

1To start, press the STOP hbutton.

2Press the MENU button.

3Select and confirm the line ’FEATURES’ .

4Select and confirm the line ’SET CLOCK’ .

SET CLOCK

TIME 20:00

YEAR 1997

MONTH 01

DATE 01

xy 0-9

5Enter the time, year, month and date.

Automatic channel search

1Switch on with the STOP hbutton. Press the menu

buttons Dand Csimultaneously.

2Select and confirm the line ’AUTO STORE’ .

The ’Automatic channel search’ function starts.

AUTO STORE

PRESS xyTO STOP

PLEASE WAIT

CHANNELS FOUND: 1

aaabbbbbbbbbbbbbbbbb

3Wait until all TV channels have been stored.

All TV channels will be stored from programme number 1

upward.

How to search for a TV channel manually, you can read in

chapter 4 ’SPECIAL FEATURES’ in the section ’Manual

channel search’.

Note: Automatic Channel Installation (ACI), only for sets

with TELETEXT:

Some cable companies or broadcasters offer the pos-

sibility to install TV channels automatically with ’ACI’.

Information about the installation offered and how to

select it, will appear in the display.

This set will recognize and install TV channels with ’ACI’

automatically.

TV channels will be stored from programme number 1

onward.

If ’ACI’ cannot identify a TV channel, you can search for

it using the method as described in the section ’Manual

channel search’.

* If the ’Automatic channel search’ function is activated,

any previously programmed TIMER blocks will be

cleared.

You can store up to 69 TV channels.

Allocating channel numbers

1Switch on with the STOP hbutton. Press the menu

buttons Dand Csimultaneously.

2Select and confirm the line ’SORT’ .

SORT vw

C-21

FROM P01

TO P02

STORE

3On the TV screen, in the line ’FROM’ , select the TV

channel to which you want to allocate a programme

number, e.g.: ’P 01’ .

4In the line ’TO’ , select the required programme number,

e.g.: ’P 02’ .

5Select and confirm the line ’STORE’ .

The allocated TV channels will be exchanged.

6Repeat steps 3to 5until you have allocated a pro-

gramme number to all the required TV channels.

To finish, press the MENU button twice.

1Insert a cassette into the cassette slot.

2Press the GPLAY playback button.

3Picture search: Now press the H(rewind) or I

(wind) button once or several times.

4Interrupt: Press the STOP hbutton.

5Wind: Stop the tape and press the H(rewind) or the

I(wind) button.

6Eject: Press the Jbutton on the set.

Note: Some functions switch off automatically after a

while (e.g.: Pause, Still Picture, Scanning). This helps to

protect the cassette and prevent unnecessary power

consumption.

* With this set you can play back cassettes that have

been recorded on another TV combi in the NTSC

standard.

* If you load a cassette with erase protection, the TV

Combi starts playback automatically.

* The picture quality is affected during scanning. The

sound is switched off.

* Remove the cassette before transporting the TV

Combi.

Still picture

1Press the STILL Rbutton. You see a still picture.

Interference stripes will appear.

Each time you press the STILL Rbutton again the pic-

ture will move on one step.

Continuous playback

1Press the MENU button.

2Select and confirm the ’SPECIAL’ line.

3Select the ’REPEAT PLAY’ line. Switch on the continuous

playback.

4Press the MENU button.

5Start the continuous playback with the GPLAY playback

button.

6If you want to cancel the function, stop the continous

playback in the ’REPEAT PLAY’ line.

Tape position/Index search

Tape position: If you press the OK button the tape position

will be shown in the display during Wind, Rewind, Record,

Playback and Pause/Stop.

Index search: Every time you start to record, the tape is

marked with a code mark.

1Press the INDEX Ebutton. Press the Ibutton to

select the next code mark or the Hbutton for the

previous code mark.

2Once the TV Combi finds the code mark or unrecorded

area it will automatically switch to playback.

Note: When you press any tape transport button (e.g.:

the Hor Ibutton) this search function will be

stopped.

* You cannot use this function with recordings made on

another video recorder that does not have this function.

Eliminating picture interference

1During playback press the MENU button.

2Select and confirm the ’SPECIAL’ line.

3Select the ’TRACKING’ line.

4Press the Dor Cbutton until the playback

quality is at its best.

5Press the MENU button. This setting will remain until

you remove the cassette.

6Cleaning function: Press the MENU button.

7Select and confirm the ’SPECIAL’ line.

8Select the ’CLEANING’ line.

9Press the OK button. A blue screen appears for a few

seconds.

0Wait until the blue screen disappears and press the

MENU button.

Note:

* Some hired cassettes may have a poor picture/sound

quality. This is not a fault in your set.

2. PLAYBACK

1Insert a cassette.

2Use the Ppbutton to select the programme number

from which you wish to record, e.g.: ’P 01’ .

3Press the RECORD nbutton.

4Use the STOP hbutton to stop the recording.

5If, whilst recording, you want to switch off the TV screen,

press the STANDBY mbutton once.

To switch the TV screen on again, press the Pp

button.

Important notes for recoding

•OTR: If you do not want to record to the end of the

cassette, press the RECORD nbutton again. The display

shows at what time the recording will stop.

With the Dor the Cbutton you can change the

end time of the recording in 30 minute intervals.

If you wish to cancel the end time, press the CLEAR

button. This does not effect the recording.

•Programme number ’E1’ is provided for recording from

external sources (via the EXTERNAL scart socket).

•Programme number ’AV’ is provided for recording from

external sources (via the front socket).

•Erase protection: So that you don’t accidentally delete an

important recording, you can remove the special tab

(erase protection) on the narrow side of the cassette with

a screwdriver or slide the special tab to the left.

Later, if you no longer want the cassette to be erase

protected, you can seal the gap again with adhesive tape

or slide the special tab to the right.

•Auto-assembling: You can use the auto-assembling func-

tion to join individual recordings without any major

picture disturbance between the recordings.

Search for the correct position on the tape and then stop

the playback by pressing the STOP hbutton. ’PAUSE’

appears in the display.

Now start recording as usual by pressing the

RECORD nbutton.

•Long play: Before recording, press the MENU button.

Select and confirm the ’SPECIAL’ line.

Select and confirm the ’TAPE SPEED’ line.

Select the ’LP’ (=LongPlay) recording speed and stop by

pressing the MENU button.

During playback the TV Combi will automatically select

the correct playback speed.

Programme a recording

The set needs the following information for every pro-

grammed recording:

* the date on which the recording is to be made

* the programme number for the TV channel

* the start and end time of the recording

* VPS/PDC on or off

The set stores all the information mentioned above in what is

known as a TIMER block. It can store 6 TIMER blocks for up

to one month in advance.

’VPS’ (Video Programming System)/ ’PDC’

(Programme Delivery Control)

With ’VPS/PDC’, the TV station controls the start and the

duration of a programmed recording. This means that the

video recorder switches itself on and off at the right time

even if a TV programme you have programmed begins earlier

or finishes later than expected.

Usually the start time is the same as the ’VPS/PDC’ time. If,

however, a different ’VPS/PDC’ time is given, e.g.: ’20.15

(VPS/PDC 20.14)’, you have to enter ’20.14’ (the ’VPS/PDC’

time) exactly to the minute.

If you are not using ’VPS/PDC’, the ’VPS/PDC’ indication must

be off.

3. RECORD

Programming with ’VIDEOPlus+’

All the information required for programming is encoded in

the ’VIDEOPlus+’ code.

1Press the SV/V+ button on the remote control.

2Enter the entire ’VIDEOPlus+ code’. This code (up to 9

digits) is found next to the start time of a TV programme

in your TV guide.

If you entered an incorrect code number, clear it with the

CLEAR button.

VIDEOPLUS

CODE

DAILY/WEEKLY ONCE

PROGRAMME NR. 01

xy 0-9 OK

3If you want to repeat programming at daily or weekly

intervals, select the required setting in the ’DAILY/WEEK-

LY’ line.

’Daily’ programming can only be used for recordings to

be made from Mondays to Fridays inclusive.

4After the confirmation the corresponding data appears on

the TV screen.

Note: If you use ’VIDEOPlus+’ for the first time, the

’PROGRAMME NR.’ line appears when you enter the

’VIDEOPlus+’ code. Enter the required programme num-

ber for this TV channel.

DATE DW PR START END d

01 01 17:15 18:45

vw xy 0-9 OK

5Confirm with the OK button.

The data has been stored in a TIMER block.

Please ensure that you loaded a cassette without erase

protection.

6Press the STANDBY mbutton.

How to enter, check or clear a TIMER

block manually

1Press the TIMER kbutton.

2Select a free TIMER block or the TIMER block you want

to check or clear.

3Clear: Press the CLEAR button.

4Enter/Check: Press the Dor Cbutton to switch

between ’DATE’ (date), ’DW’ (daily, weekly), ’PR’ (pro-

gramme number), ’START’ (start time) and ’END’ (end

time).

Press the Aand the B, or the 0-9 buttons to

change the data.

5To end programming, press the MENU button.

6Press the STANDBY mbutton.

Important notes for programmed recordings

•If the message ’PLEASE PRESS STOP’ or ’PLEASE PRESS

STANDBY’ appears on the TV screen, press the

STOP hor the STANDBY mbutton.

A TIMER recording will function only, if the set isn’t used

for other video recorder functions (e.g.: playback).

•The TIMER lamp on the front of the set lights up when

one or more of the TIMER blocks are occupied.

•If the end of the cassette is reached during a recording,

the video recorder automatically ejects the cassette. The

set switches off after a few minutes.

•If you forget to load a cassette, ’NO CASSETTE CANNOT

RECORD’ will appear.

•If you inserted a cassette with erase protection when you

want to start a recording, the cassette will be ejected.

•If ’CODE ERROR’ appears on the TV screen, you entered

an incorrect code number or the incorrect date. Repeat

the entry or end with the STANDBY mbutton.

With ’Daily’ programming, the first recording must take

place within a week.

•If ’DAILY ERROR’ appears on the TV screen, the date was

incorrectly entered. ’Daily’ programming can only be used

for recordings to be made from Mondays to Fridays

inclusive.

•The programmed recording will always be made at the

recording speed (SP/LP) that has already been selected

on the TV Combi.

How to read TELETEXT

•Press the TELETEXT ebutton to switch the TXT decoder

on and off. The TV-VIDEO Combi is now receiving the TXT

of the TV channel currently selected.

•To store the current page, press the OK button.

•If you want to select an other page, type in the number

with the digit buttons 0-9 .

Extra TELETEXT functions

•If you want to superimpose the clock time, press the

CLOCK .button.

•If you want to go to TELETEXT page 100, press the

INFO ,button.

•If you want TELETEXT to be shown transparently, press

the TRANSP. -button.

To use the extra TELETEXT functions, press the MENU but-

ton, when you are in TELETEXT.

•To enlarge the print, select the symbol ’ e; ’ and confirm

with the OK button.

•To switch off the TELETEXT decoder temporarily, select

the symbol ’ eX’ and confirm with the OK button.

•To call up a sub-page:

1Select the symbol ’ /00 ’ and confirm with the OK but-

ton.

2Enter the page number of the sub-page.

•To call up concealed information, select the symbol ’ e?

’ and confirm with the OK button.

•To stop the pages from being turned over, select the

symbol ’ STOP ’ and confirm with the OK button.

On Screen Display (OSD)

You can switch OSD on or off.

1Press the MENU button.

2Select and confirm the ’FEATURES’ line.

FEATURES vw

PP RECALL

ON TIMER

SLEEPTIMER 0

DISPLAY FULL

CHILD LOCK OFF

SET CLOCK

3Select the ’DISPLAY’ line.

4Select one of the options indicated.

’FULL’: OSD appears for a few seconds each time an

operating mode is selected and then disappears.

’OFF’: OSD is switched off.

’PROG’: only the programm number appears.

’COUNT’: only the counter appears.

5Confirm it with the MENU button.

Note: With the OK button you can superimpose the

actual operating mode on the TV screen.

Personal Preset

You can make your personal picture and volume settings

here. You can call up this setting and it will be used

automatically when you switch the set on.

1Select your personal setting. (see chapter ’The TV set

functions’). Press the menu buttons Dand C

button simultaneously.

2Select and confirm the ’PP STORE’ line.

3To end press the MENU button. The personal setting

has been stored.

4Calling up your Preset: Press the MENU button.

5Select and confirm the ’FEATURES’ line.

6Select and confirm the ’PP RECALL’ line.

7Press the MENU button. The set will use this setting.

Sleep function (switch off)

You can programme your set to switch off after a predeter-

mined period.

1Press the MENU button.

2Select and confirm the ’FEATURES’ line.

4. SPECIAL FEATURES

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Philips Fernseher Handbücher

Philips

Philips 201T1SB/00 Bedienungsanleitung

Philips

Philips TES2.0E Bedienungsanleitung

Philips

Philips 47PFL5704D - 47" Class Full Hd 1080p Lcd Tv... Konfigurationshandbuch

Philips

Philips 26PW9100D - Hook Up Guide Bedienungsanleitung

Philips

Philips 32PHD6917 Bedienungsanleitung

Philips

Philips 19-MONO COLOR TV W-REM CONT-CHARCOAL-20LL200 Bedienungsanleitung

Philips

Philips 65PUT8516 Bedienungsanleitung

Philips

Philips 7906 Series Bedienungsanleitung

Philips

Philips 32HFL5014 Bedienungsanleitung

Philips

Philips 55PFL4901 Bedienungsanleitung

Philips

Philips 9206 Series Bedienungsanleitung

Philips

Philips LC4.41E Bedienungsanleitung

Philips

Philips 29PT5460/01 Bedienungsanleitung

Philips

Philips 43PUT7428 Bedienungsanleitung

Philips

Philips 8217 Series Bedienungsanleitung

Philips

Philips 6002 Series Bedienungsanleitung

Philips

Philips Chassis TPM16.4L LA Bedienungsanleitung

Philips

Philips 9506 Series Bedienungsanleitung

Philips

Philips 32PW9788 Bedienungsanleitung

Philips

Philips 40PFG6110/77 Bedienungsanleitung

Philips

Philips 32PFL5206H Bedienungsanleitung

Philips

Philips 32PW8760/05 Bedienungsanleitung

Philips

Philips 24PHS5507/12 Bedienungsanleitung

Philips

Philips 55PUT7906/57 Bedienungsanleitung

Beliebte Fernseher Handbücher anderer Marken

Toshiba

Toshiba 27A10 Bedienungsanleitung

Hitachi

Hitachi 32FX48B Bedienungsanleitung

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Bedienungsanleitung

Changhong Electric

Changhong Electric uhd55b6000is Bedienungsanleitung

Panasonic

Panasonic Genus TX-G10 Bedienungsanleitung

Toshiba

Toshiba 19A20 Bedienungsanleitung

Sony

Sony XBR-100Z9D Bedienungsanleitung

Samsung

Samsung 55S9 B Series Bedienungsanleitung

Sharp

Sharp LC-40FI5012E Bedienungsanleitung

Loewe

Loewe Table Stand Reference 55 Bedienungsanleitung

Sylvania

Sylvania 6427FB Bedienungsanleitung

Sanyo

Sanyo CE19LD90N-B Bedienungsanleitung

North State

North State TV2GO Bedienungsanleitung

RCA

RCA RTU7877 Bedienungsanleitung

Sharp

Sharp 21K-FG1RU Bedienungsanleitung

Sony

Sony Esprit TAV-L1 Bedienungsanleitung

Grundig

Grundig 43 VLE 4820 Bedienungsanleitung

Samsung

Samsung LN26C350D1D Bedienungsanleitung