Phistek ZE6000 Montage- und Bedienungsanleitung
20141229 V2 1
U
Us
se
er
r
M
Ma
an
nu
ua
al
l
/
/
I
In
ns
st
ta
al
ll
la
at
ti
io
on
n
G
Gu
ui
id
de
e
A
AV
V
O
Ov
ve
er
r
E
Et
th
he
er
rn
ne
et
t
G
Gi
ig
ga
ab
bi
it
t
A
Ad
da
ap
pt
to
or
r
M
Mo
od
de
el
l
N
No
o.
.
Z
ZE
E6
60
00
00
0/
/
Z
ZE
E6
60
00
00
0
Warning! It will cause malfunction if the AV Adaptor is operating with unspecified power supply
adaptor or incorrect power voltage. Do not expose this unit in the rain or moisture environment to
reduce the risk of fire or electric shock.
PRECAUTIONS
Do not use the “AV adaptor” and “Power supply Adaptor” near water.
The “AV adaptor” is featured with 75mm x 75mm and 100mm x 100mm VESA mount.
For easy and safe use, it is recommended to mount ”AV adaptor” on the rear cover of monitor with
VESA mount.
The “AV Adaptor” should be operated by an Ethernet cable with standard RJ-45 connector on both
ends. One end to the “AV adaptor”, the other end to host PC or server.
Never spill liquids on the “AV Adaptor”.
Do not attempts to service ”AV adaptor” yourself; opening or removing covers can degrade product
EMC and performance. Please refer all servicing to qualified service personnel.
For Wall mount “Power supply adaptor”, wall socket shall be installed near the equipment and shall
be easily accessible.
20141229 V2 2
Index:
I. Introduction --------------------------------------------------------------------------------------------------- 3~4
Features--------------------------------------------------------------------------------------------------------- 3
Unpack the Adaptor------------------------------------------------------------------------------------------- 3
Check Accessories--------------------------------------------------------------------------------------------- 4
II. Reco ended network application and setting ---------------------------------------------------- 5~10
Basic Extended Mode(or Mirror Mode) ----------------------------------------------------------------- 7~10
ZE6000 extended mode with Phistek eSignage ---------------------------------------------------- 10
Zero Client with Userful Linux Multi-seat --------------------------------------------------------------- 10
Zero Client with WMS2012 Multipoint ------------------------------------------------------------------ 11
III. Driver Installation -------------------------------------------------------------------------------------------- 12~19
eSignage need to open Microsoft Framework--------------------------------------------------------12
Install Elite USB Server--------------------------------------------------------------------------------------- 13~14
Install SMSC Driver-------------------------------------------------------------------------------------------- 15~16
Install EETI Touch Driver ------------------------------------------------------------------------------------- 17~20
IV. Mechanical Di ension and Input/ Output ports description ----------------------------------- 21
V. Output signals installation --------------------------------------------------------------------------------- 22
VI. Adaptor installation ---------------------------------------------------------------------------- ------------22~23
VII. FCC Warning State ent ------------------------------------------------------------------------------------ 24
VIII. Product General Specification ---------------------------------------------------------------------------- 25
Appendix: Network IP address setting ----------------------------------------------------------------------------- 26~29
20141229 V2 3
I. Introduction
ZE6000/ ZE6000 is a Zero Client Audio/Video over Ethernet Adaptor, designed as an endpoint
of a PC sharing solution such as Windows MultiPoint Server 2012 or Userful Multiplatform.
With Windows MultiPoint Server 2012, or with Userful Multiplatform it can work as a
standalone workstation.
The solution enables a host PC(Server) to communicate with multiple and independent stations.
Each station is consisted of one Adaptor (zero client) with a keyboard, mouse, and monitor
connected, allowing multiple users to share the resources/computing of one single server.
By simple Ethernet connection, the server provides each station user with a familiar and
independent Windows® experience.
ZE6000 is a ZE6000 add with embedded access code in order to use Phistek special software
application, such as eSignage
Features
-Si ple Ethernet connection
ZE6000/ ZE6000 connect to Host server through Ethernet cable connection, this type of
connection can exceed the length limit of other signal connection such as VGA, USB. This also
gives the flexibility of system layout.
-Si ple plug and play
Just attach a keyboard, mouse, and monitor to your ZE6000/ ZE6000 , and connect it to the host
server.
A station is set up easily and ready for use right away
-Easy and convenient installation
Designed with VESA standard mounting on the adaptor box;
75mm x 75mm and 100mm x 100mm
-Provides three types of video signals for end user to select
DVI (through a DVI to DVI cable)
VGA (by an attached DVI to VGA dongle)
HDMI (through a DVI to HDMI cable)
-Reset: To reset IP address
-Audio Line out
-Headphone out
-Microphone in/out
Unpack the Adaptor
-Put the AV Adaptor on a clean surface; make sure the box in upright position.
-Remove packing materials from inside of box.
20141229 V2 4
Check accessory
Please make sure the entire accessory is included:
OR
DVI to VGA
Dongle
DC 12V Power Adaptor
ZE6000 User Guide &
Driver CD
ZE6000+User Guide &
Driver CD
20141229 V2 5
II. Reco ended network application and setting:
The Phistek ZE6000/ ZE6000 can be configured to the following modes:
-Basic Extended mode
Multiple extended displays block diagram :
-Zero Client with Userful Multiplatform
-Zero Client With WMS2012 Multipoint
Ethernet( LAN) network connection
Audio
Audio
LAN cable
LAN cable
LAN cable
LAN cable
LAN cable
VGA/ DVI-D/
HDMI
Host PC
Gigabit LAN switch
ZE6000
#1
ZE6000
#2
ZE6000
#3
ZE6000
#4
Monitor
Display 1
Monitor
Display 2
Monitor
Display 3
Monitor
Display 4
Audio
Audio
VGA/ DVI-D/
HDMI
VGA/ DVI-D/
HDMI
VGA/ DVI-D/
HDMI
20141229 V2 6
-ZE6000+ apply with Phistek eSignage+
20141229 V2 7
1. Basic Extended Mode (or Mirror Mode):
Please note that Extended ode only provide extended function of video display, audio,
USB ports.
1.1 Set Up Procedures:
1.1.1 Required Hardware Ingredients
The ZE6000/ ZE6000+ Zero-Client: typically available directly from PHISTEK.
The host co puter: should be scaled according to the usage scenarios
CPU Intel i7 Intel i5 Intel i3 Inel Atom D525
DRAM 8G 8G 4G 2G
OS Win7 64bit Win7 64bit POS Ready7 POS Ready2009
Video 1080p 8 sets(max) 6 sets(max) 0 set 0 sets
Video 720p 8 sets(max) 8 sets(max) 1 sets(max) 0 sets
Photo 1920x1080 8 sets(max) 8 sets(max) 4 sets(max) 4 sets(max)
1.1.2 The LAN network: 10/100M or 1000M Ethernet, recommend Gigabit-Switched,
and ideally having a dedicated switch per each cluster.
1.2 Installation:
Part 1: Host PC Windows OS Preparations
1) Host PC to run Windows-Update and install all available updates.
2) Make sure to install the latest driver for the graphic card (applies to on-board as well).
3) Turn off Windows-Update device driver searching
http://technet.microsoft.com/en-us/library/cc753091.aspx
4) Set Host PC TCP/IPV4 to DHCP
Part 2: Elite Driver installation:
1) Install Elite Driver: (See Page 12, Section III, 1.0)
2) Reboot your computer
Part 3: SMSC Driver Installation & prepare Zero-Client
1) Install SMSC display driver: (See Page 14 Section III, 2.0)
2) Connect all Zero-Clients to Ethernet Switch.
Connect monitors, and sound devices to each client.
3) Launch the Network USB Setting Utility from its desktop shortcut.
Network USB Setting Utility shortcut
20141229 V2 8
4) This program will search for ZE6000/ZE6000 Zero-Clients:
5) Click “Configuration”, tick “DHCP”
6) Per each cluster, per each client terminal:
Click “Assign to this PC”:
7) Windows will identify and install USB sound driver.
8) A dialog may pop up – search for Zero Client software – click cancel.
20141229 V2 9
9) Each client connection will be completed as below:
10) At this stage, you should be able to see all the assigned monitors in active Windows
Desktop mode.
11) Start “ViewSpan Configuration” in the Task-Bar.
Make sure to set all zero client monitors as “Extended”
20141229 V2 10
12). Set up maximum no. zero clients in application
After SMSC driver installation, the system will set number of zero clients in application at”4”
If user wants to connect for more clients, user need to execute “regedit.exe”
Simply input “regedit “to search this application.
Then follow the route:
HKEY_LOCAL_MACHINE/SYSTEM/CurrentControlSet/services/sgfxk :
MAxNumberOfUsbAdapters REG_DWORD 0x00000004 (4)
The default number is 4, click MAxNumberOfUsbAdapters to change number
The numbers of clients to use depend on the Host PC resources,
Recommend maximum number set <10
2. ZE6000+ extended ode with Phistek eSignage+ application software
2.1 With Phistek eSignage , user can broadcast and monitor extended zero clients
display on the Host PC control center ( see details in eSignage application Doc.)
2.2 Drivers:
Follow “Basic extended mode” drivers installation, except Elite Driver is replaced
by “eSignage ” driver
2.3 eSignage driver download ,
code.
3. Zero Client with Userful Multiplatfor
3.1 With Userful Multiplatfor , ultisuers can work independently as a zero
client , standalone workstation.
3.2 Pls visit userful Linux website to get Userful Multiplatform.
http://support.userful.com/Manuals/Userful_Multiplatform/Installation
3.3 Userful reco ended PC Syste equip ent:
For up to 6 stations:
• Dual Core Processor
• 2GB RAM
• 1 high-speed USB controller interface
Andere Handbücher für ZE6000
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
