Phoenix Model Tiger Moth Bedienungsanleitung

Instruction Manual

version EP

version

SPECIFICATION

- Wingspan: 2270mm (89.4in)

- Length: 1870mm (73. 6 in)

- Flying weight: 8.4-8.9 kg

- Wing area: 154 dm2

- Wing loading: 69g/dm2

- Wing type: Naca profile

- Covering type: OraCover

- Spinner size: scale type (not included)

- Radio: 4 channel minimum (not included)

- Servo: 6 standard hi-torque servo: 2 aileron;

2 elevator; 1 rudder; 1 throttle (not included)

- Recommended receiver battery:

4.8-6V / 1200-2000mAh NiMH (not included)

- Propeller: suit with your engine

- Engine: 30-35cc gas engine (not included)

TIGER MOTH

GP/EP Size 30-35CC SCALE 1:6 ¼ ARF

- Motor: brushless outrunner 2500 W,

250 KV (not included)

- Gravity CG: 190 mm (7.5 in) Back from the

leading edge of the upper wing, at the fuselage

- Control throw Ailerons: Low: 15mm up/down,

10% expo; High: 20mm up/down, 10% expo

- Control throw Elevators: Low: 12mm up/down,

12% expo; High: 15mm up/down, 12% expo

- Control throw Rudder: Low: 35mm right/left,

15% expo; High: 45mm right/left, 15% expo

- Experience level: Intermediate

- Plane type: Scale Civilian

RECOMMENDED MOTOR AND BATTERY SET UP

- Motor: RIMFIRE 1.60 (not included)

- Lipo cell: 12 cells / 5000 – 6000mAh (not included)

- Esc: 120-160A (not included)

TOOLS AND SUPPLIES NEEDED.

• Medium C/A glue

• 30 minute epoxy

• 6 minute epoxy

• Hand or electric drill

• Assorted drill bits

• Modeling knife

• Straight edge ruler

• 2 bender plier

• Wire cutters

• Masking tape

• Thread lock

• Paper towels

• Rubbing alcohol

SUGGESTION

To avoid scratching your new airplane, do not unwrap

the pieces until they are needed for assembly. Cover

your workbench with an old towel or brown paper,

both to protect the aircraft and to protect the table.

Keep a couple of jars or bowls handy to hold the

small parts after you open the bag.

NOTE:

Please trial fit all the parts. Make sure you have the

correct parts and that they fit and are aligned properly

before gluing! This will assure proper assembly. The

TIGER MOTH GP/EP Size 30-35CC SCALE 1:6 ¼

ARF is hand made from natural materials, every

plane is unique and minor adjustments may have to

be made. However, you should find the fit superior

and assembly simple.

The painted and plastic parts used in this kit are fuel

proof. However, they are not tolerant of many harsh

chemicals including the following: paint thinner, C/A

glue accelerator, C/A glue debonder and acetone. Do

not let these chemicals come in contact with the

colors on the covering and the plastic parts.

SAFETY PRECAUTION:

• This is not a toy

• Be sure that no other flyers are using your radio

frequency.

• Do not smoke near fuel

• Store fuel in a cool, dry place, away from

children and pets.

• Wear safety glasses.

• The glow plug clip must be securely attached to

the glow plug.

• Do not flip the propeller with your fingers.

• Keep loose clothing and wires away from the propeller.

• Do not start the engine if people are near. Do not

stand in line with the side of the propeller.

• Make engine adjustments from behind the propeller

only. Do not reach around the spinning propeller.

PREPARATIONS

Use a covering iron with a covering sock on

high heat to tighten the covering if necessary.

Apply pressure over sheeted areas to

thoroughly bond the covering to the wood.

INSTALLING THE AILERONS AND Flaps

1. Test fit the ailerons to the wing with the hinges.

If the hinges don’t remain centered, stick a pin

through the middle of the hinge to hold it in

position.

TEMPORARY PIN

TO KEEP HINGE

CENTERED

2. Apply six drops of thin CA to the top and bottom

of each hinge. Do not use CA accelerator. After

the CA has fully hardened, test the hinges by

pulling on the aileron.

TIGER MOTH

Instruction Manual

< Bottom view >

Main Wing

Aileron

INSTALLING THE AILERONs SERVOS

1. Install the rubber grommets and brass eyelets onto

the aileron servo.

2. Using a modeling knife, remove the covering from over

the pre-cut servo arm exit hole on the aileron servo

tray / hatch. This hole will allow the servo arm to pass

through when installing the aileron pushrods.

3. Place the servo into the servo tray. Center the servo

within the tray and drill pilot holes through the block

of wood for each of the four mounting screws

provided with the servo.

4. Using the thread as a guide and using masking

tape, tape the servo lead to the end of the

thread: carefully pull the thread out. When you

have pulled the servo lead out, remove the

masking tape and the servo lead from the

thread.

5. Place the aileron servo tray / hatch into the servo

box on the bottom of the wing and drill pilot

holes through the tray and the servo box for

each of the four mounting screws. Secure the

servo tray in place using the mounting screws

provided .

6. Repeat step # 2 - # 5 to install the second aileron

servo in the opposite wing half.

Make certain the hinges are adequately secured with glue. If

they come loose in flight accidents may result.

Secure nylon hinges with instant glue, being careful

not to glue the wing and airleron together.

Apply instant glue (CA glue, super glue). Align the center line of main wing with aileron.

Cut away film only. here

Supplied with the servo

approx. 13mm

2mm

Must be purchased

separately!

Assemble left and right

sides the same way

TIGER MOTH

Instruction Manual

Cut off shaded portion

< Bottom view >

Aileron

1.5mm

Aileron Servo

TIGER MOTH

Instruction Manual

Assemble left and right

sides the same way

Must be purchased separately!

Set all scerws securely. If they come

off during flight you will lose control

of your aircraft!

Tie the string.

Pull out servo cord with string.

2 x 10mm TP Screw

Warning!

2x10mm

TIGER MOTH

Instruction Manual

Cut off shaded portion

Assemble left and right

sides the same way < Bottom view >

Apply threadlocker

(screw cement).

3x12mm

Aileron

3x12mm

3mm

Aluminum ball

INSTALLING THE AILERONs LINKAGES

Nut

3mm

Nylon Nut

3mm

Aluminum ball

3 x 25mm Cap Screw

80mm Push rod

3 x 12mm Screw

3mm Washer

3x25mm

TIGER MOTH

Instruction Manual

Cut off shaded portion

Assemble left and right

sides the same way

< Bottom view >

Aileron Rod

Neutral

4mm Washer

4mm Spring Washer

4 x 20mm Cap Screw

SECURE The LOW Wing To The Fuselage

Attach the wings to the joiner tube and secure

the wing panels to the fuselage.

TIGER MOTH

Instruction Manual

White glue

4x20mm

4mm

Plastic

Assemble left and right

sides the same way.

Cut off shaded portion

Rubber band

Assemble left and right

sides the same way.

TIGER MOTH

Instruction Manual

3 x 10mm TP Screw

4 x 10mm Button Screw

Plate of plywood

3x10mm

130mm

15mm

10mm

Plate of plywood

4x10mm

Make sure there is

no slack on the wire

and close pipe

Cut off excess.

3mm

Cable rod Cable rod

3 x 10mm TP Screw

4 x 10mm Button Screw

4x10mm

Silicone

Cable

Cut off shaded portion

SECURE The HIGH WING To The Fuselage

Attach the wings to the joiner tube and secure

the wing panels to the fuselage.

Cap screw high wing

TIGER MOTH

Instruction Manual

TIGER MOTH

Instruction Manual

Apply threadlocker

(screw cement).

3 x 15mm TP Screw

Plate of plywood

INSTALLING THE MAIN LANDING GEAR

4mm Spring Washer

4 x 20mm Cap Screw

8mm Collar

8mm

Andere Handbücher für Tiger Moth

Inhaltsverzeichnis

Andere Phoenix Model Spielzeug Handbücher

Phoenix Model

Phoenix Model Tiger 60 Bedienungsanleitung

Phoenix Model

Phoenix Model Extra 300S Bedienungsanleitung

Phoenix Model

Phoenix Model SBD DAUNTLESS Bedienungsanleitung

Phoenix Model

Phoenix Model TUCANO 60CC Bedienungsanleitung

Phoenix Model

Phoenix Model Edge 540 Bedienungsanleitung

Phoenix Model

Phoenix Model LASER Bedienungsanleitung

Phoenix Model

Phoenix Model Extra 330S Bedienungsanleitung

Phoenix Model

Phoenix Model Katana 120 Bedienungsanleitung

Phoenix Model

Phoenix Model Classic Bedienungsanleitung

Phoenix Model

Phoenix Model PC21 PILATUS Bedienungsanleitung

Phoenix Model

Phoenix Model Edge 540 Bedienungsanleitung

Phoenix Model

Phoenix Model Pilatus-PC21 Bedienungsanleitung

Phoenix Model

Phoenix Model A26 INVADER GP Bedienungsanleitung

Phoenix Model

Phoenix Model yak 55 Bedienungsanleitung

Phoenix Model

Phoenix Model Jupiter Ultra Series Pattern Bedienungsanleitung

Phoenix Model

Phoenix Model KATANA-EP Bedienungsanleitung

Phoenix Model

Phoenix Model SBACH 342 Bedienungsanleitung

Phoenix Model

Phoenix Model EXTRA 330SC Bedienungsanleitung

Phoenix Model

Phoenix Model Dolphin 40 Bedienungsanleitung

Phoenix Model

Phoenix Model PA-18 Super Cub Bedienungsanleitung

Phoenix Model

Phoenix Model F4U Corsair Bedienungsanleitung

Phoenix Model

Phoenix Model Extra 300S Bedienungsanleitung

Phoenix Model

Phoenix Model Extra 300 S Bedienungsanleitung

Phoenix Model

Phoenix Model Dolphin 40 Bedienungsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Handbuch

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

Meccano

Meccano 15103 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung