Photoneo PhoXi 3D Scanner M Bedienungsanleitung
PhoXi 3D Scanner M
Quick Start Guide
Scope of Delivery
■PhoXi 3D Scanner M
■Power adapter (90 - 264VAC / 12VDC, 60W) (1)
■Power cable (2)
■Ethernet cable adapter (3)
■L-shaped mounting plate
Operation of the Scanner
The scanner is operated by the PhoXi Control application. PhoXi Control allows the user to
control the scanner either manually through a graphical user interface or programmatically
through the provided API.
All PhoXi Control resources can be found on the following link:
www.photoneo.com/3d-scanning-software/
Read the complete PhoXi 3D Scanner Manual for more details:
www.photoneo.com/support
01/2020 PhoXi 3D Scanner M - Quick Start Guide 1/8
Scanning Parameters - Model M
Parameter
Value
Resolution
Up to 3.2 Million 3D points
Scanning range
458 - 1118mm
Optimal scanning distance (focus)
650mm
Scanning area (at focus distance)
590 x 421mm
Point to point distance (at focus distance)
0.284mm
Calibration accuracy
0.1mm
Temporal noise
0.1mm
Scanning time
250 - 2500ms
Dimensions
77 x 68 x 416mm
Baseline
350mm
Weight
950g
3D point throughput
16 Million points per second
These parameters are valid at 25°C, at focus distance for white objects with 80 % albedo.
01/2020 PhoXi 3D Scanner M - Quick Start Guide 2/8
Scanning Volume - Model M
01/2020 PhoXi 3D Scanner M - Quick Start Guide 3/8
Mounting the Scanner
Mounting options:
■Use 4x M4 screws with the supplied mounting plate.
■Use a M8 screw.
■Use a 3/8 - 16 UNC screw with a tripod.
Installation site restrictions:
■Ensure that mounting construction is rigid enough to avoid vibrations during scanning.
■Allow clearance of 25 mm for natural convection cooling.
■The ambient temperature range for the scanner operation is 0 °C to 30 °C.
■Separate the scanner from high-voltage devices and devices generating high electrical
noise.
The complete environment conditions for installation can be found in the full user manual at
www.photoneo.com/support
01/2020 PhoXi 3D Scanner M - Quick Start Guide 4/8
Connecting to the Scanner
Ethernet port:
■1Gbps ethernet adapter with RJ45
socket
■Category Cat5e or better ethernet
cables
■PoE is not supported
Power + GPIO port:
■12VDC power supply
■Use only the supplied power
adapter
■The I/O ports are reserved for
future use
Ethernet Pinout
Power Pinout
Pin
Pinout
Pin
Pinout
1
MD1_P
1
IN2: laser interlock (5 - 12V)
2
12V_IN
2
IN1
3
MD2_N
3
OUT2
4
MD2_P
4
OUT1
5
MD0_P
5
POWER_+12VDC
6
MD0_N
6
POWER_GND
7
MD3_P
7
GPIO1
8
GND
8
GPIO3
9
MD1_N
9
GPIO2
10
MD3_N
10
IN_GND: laser interlock ground
11
OUT_GND
12
GPIO4
01/2020 PhoXi 3D Scanner M - Quick Start Guide 5/8
Status LEDs
The LEDs indicate the following states of the scanner:
Supported Network Topologies
01/2020 PhoXi 3D Scanner M - Quick Start Guide 6/8
Made-to-Order Cables
The following cables are available for additional purchase in standard or industrial quality:
■Power cable (from power adapter to device)
■Ethernet cable
All cables are available in the following lengths:
■3 m, 5 m, 10 m, 15 m.
Our industrial ethernet cables are sheathed in polyurethane jackets for high flexibility,
durability, and resistance to chemicals, water, and UV.
Our industrial power cables are sheathed in flex polyvinyl chloride jackets for high flexibility
and resistance to oils, water, and UV.
Custom Cables
■In case custom cables are used, the voltage must reach 12 V at the device end.
■Longer custom cables should have wires of a larger diameter to compensate for
voltage losses.
■When using custom cables, any damage caused to the device due to incorrect voltage
is exempt from warranty.
■Powering the device through the ethernet connector (PoE) is not possible.
Operating voltage Ue DC
12V
Residual ripple maximum (% of Ue)
5%
Rated operating current Ie(Imax)
2A (3A)
WARNING
Not ensuring the correct voltage at the device end may negatively influence
the correct functionality of the device or cause permanent damage.
01/2020 PhoXi 3D Scanner M - Quick Start Guide 7/8
Safety
PhoXi 3D Scanner Model M is a laser class 3R device or a laser class 2 device. Class 3R
lasers are considered safe when handled carefully. Class 2 lasers are considered safe for
normal operation. See the label on the back of the device to determine its laser class.
Laser class 3R label
Laser class 2 label
WARNING
Do not deliberately look into the laser beam. This may cause injury
to the retina.
Laser protective eyewear is normally not necessary.
Contact Us
Headquarters
Photoneo s.r.o.
Plynarenska 1
82109 Bratislava
Slovakia
01/2020 PhoXi 3D Scanner M - Quick Start Guide 8/8
Andere Handbücher für PhoXi 3D Scanner M
1
Inhaltsverzeichnis
Andere Photoneo Scanner Handbücher
Photoneo
Photoneo PhoXi Bedienungsanleitung
Photoneo
Photoneo PhoXi XS Bedienungsanleitung
Photoneo
Photoneo PhoXi 3D Scanner XS Bedienungsanleitung
Photoneo
Photoneo MotionCam-3D M Bedienungsanleitung
Photoneo
Photoneo PhoXi Bedienungsanleitung
Photoneo
Photoneo PhoXi 3D Scanner M Bedienungsanleitung
Photoneo
Photoneo PhoXi Bedienungsanleitung
Photoneo
Photoneo PhoXi 3D Scanner S Bedienungsanleitung
Photoneo
Photoneo PhoXi 3D Scanner S Bedienungsanleitung
