Phytec L-1029e.A1 Bedienungsanleitung

L-1029e.A1 phyCAM with phyBOARD-Pollux i.MX 8M

Plus Getting Started Guide

Manuals & Documentation

Exported on 09/15/2022

Manuals & Documentation – L-1029e.A1 phyCAM with phyBOARD-Pollux i.MX 8M Plus Getting Started Guide
– 2
Table of Contents
Introduction ........................................................................................................... 4
SBC Kit Start-Up ..................................................................................................... 5
1 Before You Start ........................................................................................................................... 5
Connecting and Starting the Camera.................................................................... 6
1 Overview....................................................................................................................................... 6
Camera Connectors on the Pollux - Carrier Boards.............................................. 8
1 Connecting the phyCAM-M Camera ............................................................................................ 8
Supported Camera Boards (YOCTO Linux PD21.1.1 and higher)....................... 10
1 Supported Camera Types in Standard Vision Image (phytec-vision-image-phyboard-pollux-
imx8mp-2) .................................................................................................................................. 10
2 Change the Camera Types or Connected Port in Standard Vision Image (phytec-vision-
image-phyboard-pollux-imx8mp-2).......................................................................................... 10
2.1 How to Change the Device Tree ............................................................................................................................... 11
2.2 How to activate the VM-017/VM-117 camera series ................................................................................................ 13
Demo Scripts ........................................................................................................ 14
1 GStreamer Scripts...................................................................................................................... 14
2 Scripts to Call C/C++ files Based on v4l2 Interface ................................................................... 15
3 OpenCV Scripts........................................................................................................................... 16
7Configure Camera and Controller Camera Interface with “media-ctl”............. 17
Camera Features Configuration .......................................................................... 20
1 v4l2-ctl Configuration ................................................................................................................ 20
2 Camera Register Direct Configuration ...................................................................................... 20
De-Bayering (demosaicking) with NEON CoProcessor ...................................... 21
Revision History ................................................................................................... 22

Manuals & Documentation – L-1029e.A1 phyCAM with phyBOARD-Pollux i.MX 8M Plus Getting Started Guide

– 3

L-1029e.A1 phyCAM with phyBOARD-Pollux i.MX 8M Plus Getting Started Guide

Document Title L-1029e.Ax phyCAM with phyBOARD-Pollux i.MX 8M Plus Getting

Started Guide

Document Type Hardware/Software Guide

Article Number L-1029e.A1

Release Date 28.10.2021

Is Branch of L-1029e.Ax phyCAM with phyBOARD-Pollux i.MX 8M Plus Getting

Started Guide Head

Introduction(see page 4)

SBC Kit Start-Up(see page 5)

Before You Start(see page 5)

Connecting and Starting the Camera(see page 6)

Overview(see page 6)

Camera Connectors on the Pollux - Carrier Boards(see page 8)

Connecting the phyCAM-M Camera(see page 8)

Supported Camera Boards (YOCTO Linux PD21.1.1 and higher)(see page 10)

Supported Camera Types in Standard Vision Image (phytec-vision-image-phyboard-pollux-

imx8mp-2)(see page 10)

Change the Camera Types or Connected Port in Standard Vision Image (phytec-vision-image-

phyboard-pollux-imx8mp-2)(see page 10)

How to Change the Device Tree(see page 11)

How to activate the VM-017/VM-117 camera series(see page 13)

Demo Scripts(see page 14)

GStreamer Scripts(see page 14)

Scripts to Call C/C++ files Based on v4l2 Interface(see page 15)

OpenCV Scripts(see page 16)

Configure Camera and Controller Camera Interface with “media-ctl”(see page 17)

Camera Features Configuration(see page 20)

v4l2-ctl Configuration(see page 20)

Camera Register Direct Configuration(see page 20)

De-Bayering (demosaicking) with NEON CoProcessor(see page 21)

Revision History(see page 22)

Manuals & Documentation – L-1029e.A1 phyCAM with phyBOARD-Pollux i.MX 8M Plus Getting Started Guide

Introduction– 4

1 Introduction

The SBC (Single Board Computer) kits from PHYTEC represent an ideal basis for testing and the first design steps

with phyCAM camera modules. The kit forms the starting point for your development project. The kit can be used to

develop and test application software before your own adapted hardware is available. It is also an optimal platform

for testing special hardware extensions before you create a complex application board.

This optional step secures your design while at the same time provides software developers with an opportunity to

adapt newly added hardware components. Extensions can be easily connected via the extension interfaces of the

baseboards included in the kit. In the simplest case, a freely wired hole grid structure is sufficient.

For certain combinations of controller modules, camera modules, and lenses, we offer ready-made kits. If the

combination you require is not available, we recommend that you first put a similarly-equipped kit into operation

and then connect the camera you require to the kit.

We will be happy to advise you on the best way to carry out your project.

Manuals & Documentation – L-1029e.A1 phyCAM with phyBOARD-Pollux i.MX 8M Plus Getting Started Guide

SBC Kit Start-Up– 5

•

2 SBC Kit Start-Up

Before you try out the camera and image processing functions, we recommend that you first familiarize yourself

with the basic functions of the kit and the associated development environment. Each kit contains a Quick Start

Guide that guides you through installing the software on your development PC and configuring the hardware.

2.1 Before You Start

The following components are required for the camera setup:

PHYTEC SBC-Kit with power supply and serial connection (RS232 or USB)

Camera module with camera cable, lens holder, and lens

Network cable

HDMI monitor with an HDMI cable (not included in the kit)

If you have ordered the corresponding kit as an Embedded Imaging Kit, all hardware components required for

installation are already included.

As a rule, both the extension of an existing kit by one camera and the extension of an existing video kit by additional

cameras is possible without problems with an existing phyCAM interface.

Before connecting and starting up the camera, carry out the first steps of the "Quick Start Instructions" of the

respective kit. To start the scripts on the module, follow the steps to establish a serial connection with the module.

You can use the terminal program suggested in the manual or your own terminal program.

To transfer saved image files to a PC (host) via Ethernet, follow the steps to establish an FTP connection. You can

use the FTP server suggested in the manual or your own FTP server.

Manuals & Documentation – L-1029e.A1 phyCAM with phyBOARD-Pollux i.MX 8M Plus Getting Started Guide

Connecting and Starting the Camera– 6

3 Connecting and Starting the Camera

When you purchase an SBC kit, you will receive the PHYTEC guarantee. If you encounter any difficulties during

installation, PHYTEC support will help you!

3.1 Overview

The i.MX 8M Plus Microcontroller supports two MIPI CSI-2 camera interfaces:



Camera Interfaces of i.MX 8M Plus Controller (Quad) Block Diagram

On the phyCORE-i.MX 8M Plus, the CSI1/CAM1 and CSI2/CM2 camera paths go out as CSI-2 MIPI signal:

CAM_1 (CSI1) and CAM_2 (CSI2) Present on Connector X1

Note

Depending on the kernel version, the software installation may differ in some details from the described

procedure.



Manuals & Documentation – L-1029e.A1 phyCAM with phyBOARD-Pollux i.MX 8M Plus Getting Started Guide

1 https://www.phytec.de/produkte/embedded-imaging/

Connecting and Starting the Camera– 7

On PHYTEC or customer carrier boards, the interfaces are led out as phyCAM-M. For more information on phyCAM-

M, see the phyCAM-Manuals on our website1.

On the phyBOARD-Pollux baseboard, the camera interfaces are led out as phyCAM-M (MIPI CSI-2) interfaces. Here

you can connect different phyCAM-M camera modules:

phyCAM-M Camera Interfaces of phyCORE-i.MX 8M Plus (Quad) and the output on the phyBOARD-Pollux-i.MX 8M

Plus

The BSP shipped with the Kit includes the software drivers for the supported phyCAM-M camera modules. The

drivers are compatible with v4l2. GStreamer scripts are also included for the evaluation of the camera modules. If

you need the camera interface to connect to your own camera module, an adapter to phyCAM-M is necessary.

Manuals & Documentation – L-1029e.A1 phyCAM with phyBOARD-Pollux i.MX 8M Plus Getting Started Guide

2 https://www.phytec.de/cdocuments/?doc=fAC7E

Camera Connectors on the Pollux - Carrier Boards– 8

•

4 Camera Connectors on the Pollux - Carrier Boards

The development kits for the i.MX 8M Plus phyBOARD-Pollux contains:

one carrier board (phyBOARD-Pollux)

one phyCORE-i.MX 8M Plus module SOM (phyCORE-i.MX 8M Plus)

The phyCORE-i.MX 8M Plus is plugged into the carrier board.

On the phyBOARD-Pollux baseboard (PBA-C-17), we convert the MIPI CSI-2 interfaces into a phyCAM-M standard.

phyCAM-M camera interface 1 (support on connector X11)

phyCAM-M camera interface 2 (support on connector X12)

Camera Interface on phyBOARD-Pollux up PCB Version PL1552.0

4.1 Connecting the phyCAM-M Camera

A type-A FFC cable (stripped and reinforced on the same side) is supplied with the kit. This ensures the correct

signal assignment between the camera and the baseboard in the kit.

The position of the camera socket on the baseboard can be found in the hardware manual2of the kit. Parallel to the

connector designation (e.g. X100), some basic boards also have "CAM" printed on the board. The phyCAM-M

interface is a 30-pin FFC socket, which can be installed standing or lying on the board.

The FFC cable is plugged in exactly the same way as the cable is plugged into the camera FFC socket.

Note

If you use the phyCAM-M interface, use an FFC cable that is especially suitable for FH41 connectors (e.g.

PHYTEC WF271). Standard FFC cables can cause a short circuit.



Note

In the vertical version of the FFC socket, the contacts are also on the side opposite the bracket.



Manuals & Documentation – L-1029e.A1 phyCAM with phyBOARD-Pollux i.MX 8M Plus Getting Started Guide

Camera Connectors on the Pollux - Carrier Boards– 9

Open the lock of the 30-pin FFC connector on the camera by lifting the lock upwards.

phyCAM-M Flip Lock – FCC Socket Camera Connection

Plug the 30-pin FFC cable into the FFC socket with the contact surfaces facing downwards until you feel the

stop. The reinforcement of the FFC cable (usually highlighted in color) points to the bracket of the socket.

Lock the FFC socket by carefully pressing it down on the bracket.

Manuals & Documentation – L-1029e.A1 phyCAM with phyBOARD-Pollux i.MX 8M Plus Getting Started Guide

3 https://www.phytec.de/cdocuments/?doc=VoXcEQ

4 https://www.phytec.de/cdocuments/?doc=fAC7E

Supported Camera Boards (YOCTO Linux PD21.1.1 and higher)– 10

•

5 Supported Camera Boards (YOCTO Linux PD21.1.1 and higher)

The cameras and the camera interface are supported as sub-devices. To configure the v4l2 framework is the

handler "media-ctl" used, see Configure Camera and Controller Camera Interface with "media-ctl"(see page 17)

5.1 Supported Camera Types in Standard Vision Image (phytec-vision-

image-phyboard-pollux-imx8mp-2)

Per default the following Camera types are supported in the image:

VM-016-BW-M series (VM-016-BW-M, VM-016-BW-M-M12, VM-016-BW-M-H, …) based on camera sensor

“AR0144”

VM-016-COL-M series (VM-016-COL-M, VM-016-COL-M-M12, VM-016-COL-M-H, …) based on camera sensor

“AR0144”

After login, you can start working with the Demo Scripts(see page 14).

Hardware Configuration Possible Parameters Default I²C-address

(default jumper on

camera and boards)

phyCAM Camera

Model (part

number)

Connected to csi_p

ort

cam_bus_ty

cam_i2c_a

ddress

VM-016-__-M (-M12/-

X11 on Pollux

board

1 phyCAM-M 0x10, 0x18 0x10

5.2 Change the Camera Types or Connected Port in Standard Vision

Image (phytec-vision-image-phyboard-pollux-imx8mp-2)

The following camera types are interchangeable in the image:

Tip

The device tree of the camera VM-016 (sensor AR0144) at csi_port_1 is pre-selected in PD21.1.1 To use

other the VM-016 at other port or dual or other cameras (e.g. VM-017/117) the device tree must be

changed. See Change the Camera Types in Standard Vision Image(see page 10)



Note

I²C addresses of the camera are set by hardware configuration (jumper setting on the camera and/or on

the baseboard. Please refer to theL-1018e.A0 phyCAM-M VM-016 1/4“ 1,0 MPixel Global Shutter Camera

Module Guide3and the L-1009e.A0 phyCORE-i.MX 8M Plus / phyBOARD-Pollux (1549.0 / 1552.0) Hardware

Manual4.



Inhaltsverzeichnis

Andere Phytec Computerhardware Handbücher

Phytec

Phytec L-1014e.A4 phyBOARD-Mira Bedienungsanleitung

Phytec

Phytec ATOM phyCORE-Z500P(T) Bedienungsanleitung

Phytec

Phytec phyCORE-i.MX 8M Mini Bedienungsanleitung

Phytec

Phytec phyCORE-TC399 Bedienungsanleitung

Phytec

Phytec phyCORE-i.MX 8M Plus Bedienungsanleitung

Phytec

Phytec eGrabber-4plus Bedienungsanleitung

Phytec

Phytec phyCORE-i.MX RT1170 Bedienungsanleitung

Phytec

Phytec L-1017e.A3 i.MX 8M Plus Bedienungsanleitung

Phytec

Phytec L-1009e.A2 phyCORE-i.MX 8M Plus Bedienungsanleitung

Phytec

Phytec Cosmic-AM335 Series Bedienungsanleitung

Phytec

Phytec PCAN-Dongle PK-001 Programmierhandbuch

Phytec

Phytec phyCORE-i.MX 8M Mini Bedienungsanleitung

Phytec

Phytec phyCORE-LPC3250 Bedienungsanleitung

Phytec

Phytec L-820e.A2 Bedienungsanleitung

Phytec

Phytec PhyBOARD-Mira i.MX6 Bedienungsanleitung

Phytec

Phytec microMODUL-8051 Bedienungsanleitung

Phytec

Phytec phyCORE-LPC3180 Bedienungsanleitung

Phytec

Phytec phyCORE-i.MX 8M Mini Bedienungsanleitung

Phytec

Phytec IoT-Enablement-Kit 4 Bedienungsanleitung

Phytec

Phytec L-843e.A1 Bedienungsanleitung

Phytec

Phytec phyGATE Tauri-L Bedienungsanleitung

Phytec

Phytec L-863e.A2 phyCORE-i.MX 8M Bedienungsanleitung

Phytec

Phytec phyFLEX-i.MX 6 Bedienungsanleitung

Phytec

Phytec phyCORE-PXAG49 Programmierhandbuch

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung