Pickering 40-615A Bedienungsanleitung

pickeringtest.com

Issue 2.3 May 2023

40-615A User Manual

PXI Very High Density Multiplexer Module

Page (II) VERY HIGH DENSITY MULTIPLEXER MODULE 40-615A

pickering

Page (II) REED RELAY MODULE 40-110/115/120/125

pickering

No part of this publication may be reproduced, transmitted, transcribed, translated or stored in any form, or by

any means without the written permission of Pickering Interfaces.

Technical details contained within this publication are subject to change without notice.

ISO 9001

Reg No. FM38792

Page (III)

VERY HIGH DENSITY MULTIPLEXER MODULE 40-615A

pickering

Page (III)

REED RELAY MODULE 40-110/115/120/125

pickering

TECHNICAL SUPPORT

For Technical Support please contact Pickering Interfaces either by phone, the website or via e-mail.

WARRANTY

All products manufactured by Pickering Interfaces are warranted against defective materials and workmanship for a period of

three years, excluding programmable power supplies, from the date of delivery to the original purchaser. Any product found to be

defective within this period will, at the discretion of Pickering Interfaces be repaired or replaced.

Products serviced and repaired outside of the warranty period are warranted for ninety days.

Extended warranty and service are available. Please contact Pickering Interfaces by phone, the website or via e-mail.

ENVIRONMENTAL POLICY

Pickering Interfaces operates under an environmental management system similar to ISO 14001.

Pickering Interfaces strives to full all relevant environmental laws and regulations and reduce wastes and releases to the

environment. Pickering Interfaces aims to design and operate products in a way that protects the environment and the health and

safety of its employees, customers and the public. Pickering Interfaces endeavours to develop and manufacture products that can

be produced, distributed, used and recycled, or disposed of, in a safe and environmentally friendly manner.

Worldwide Technical Support and Product Information

pickeringtest.com

Germany

Tel: +49 89 125 953 160

E-mail: [email protected]

Sweden

Tel: +46 340-69 06 69

E-mail: [email protected]

USA

Tel: (West) +1 541 471 0700

Tel: (East) +1 781 897 1710

E-mail: [email protected]

Czech Republic

Tel: +420 558 987 613

E-mail: [email protected]

France

Tel +33 9 72 58 77 00

E-mail [email protected]

Pickering Interfaces Headquarters

Stephenson Road Clacton-on-Sea CO15 4NL United Kingdom

Tel: +44 (0)1255-687900

E-Mail: [email protected]

China

Tel: +86 4008 799 765

E-mail: [email protected]

Page (IV) VERY HIGH DENSITY MULTIPLEXER MODULE 40-615A

pickering

Page (IV) REED RELAY MODULE 40-110/115/120/125

pickering

MEANING / DESCRIPTION SYMBOL

PROTECTIVE EARTH (GROUND)

To identify any terminal which is intended for connection to an external conductor for

protection against electric shock in case of a fault, or the terminal of a protective earth

(ground) electrode.

DANGEROUS VOLTAGE

To indicate hazards arising from dangerous voltages.

WARNING / CAUTION

An appropriate safety instruction should be followed or caution to a potential hazard

exists.

Refer to the relevant instructions detailed within the product manual.

HEAVY

If this product is heavy reference should be made to the safety instructions for

provisions of lifting and moving.

STATIC SENSITIVE

To indicate that static sensitive devices are present and handling precautions should

be followed.

SAFETY SYMBOLS

PRODUCT SAFETY

The following safety symbols may be used on the product and throughout the product documentation.

Page (V)

VERY HIGH DENSITY MULTIPLEXER MODULE 40-615A

pickering

Technical Support and Warranty................................................III

Product Safety .............................................................................IV

Contents (this page)....................................................................V

Warnings and Cautions ..............................................................VII

Section 1

Technical Specication...............................................................1.1

Section 2

Technical Description .................................................................2.1

Functional Description..........................................................2.1

Section 3

Installation....................................................................................3.1

Pre Operation Checks...........................................................3.1

Hardware Installation ............................................................3.2

Software Installation .............................................................3.2

Testing Operation ..................................................................3.3

Section 4

Programming Guide....................................................................4.1

Programming Options For Pickering PXI Modules ............4.1

Module Architecture - High Density 1-Pole.........................4.2

Sub-unit Cross Reference - High Density 1-Pole ...............4.3

Module Architecture - High Density 2-Pole.........................4.9

Sub-unit Cross Reference - High density 2-Pole................4.10

Module Architecture - Low Density 1-Pole..........................4.16

Sub-unit Cross Reference - Low Density 1-Pole ................4.17

Programming The Module ....................................................4.20

Section 5

Connector Information................................................................5.1

Section 6

Trouble Shooting .........................................................................6.1

Section 7

Maintenance Information............................................................7.1

Switching System Test Tools ...............................................7.1

Relay Lookup Tables.............................................................7.1

Component Layout................................................................7.2

CONTENTS

Page (VI) VERY HIGH DENSITY MULTIPLEXER MODULE 40-615A

pickering

THIS PAGE INTENTIONALLY BLANK

Page (VII)

VERY HIGH DENSITY MULTIPLEXER MODULE 40-615A

pickering

Page (VII)

2 AMP 1-POLE UHD MATRIX MODULES 40-575 / 576 / 577 / 578 / 579

pickering

WARNINGS AND CAUTIONS

WARNING - HAZARDOUS ENVIRONMENTS SYMBOL

This product is not specically designed for use in hazardous environments, for example in explosive

atmospheres. If the product is to be used in hazardous environments we recommend that the user

ensures suitable protective measures are taken.

WARNING - DANGER OF ELECTRIC SHOCK SYMBOL

This module may contain hazardous voltages. Before removing the module from the rack remove all

supplies and disconnect user I/O signals.

Unused slots in the host chassis are populated with blanking plates to prevent access to user I/O

signals that may be present. Blanking panels are available to order from Pickering in a variety of

slot widths. If the product is not used in this manner for example by using an extender card then

additional care must be taken to avoid contact with exposed signals.

Not to be used in safety critical circuits, refer to the Pickering Interfaces’ terms & conditions of sale.

This module must not be used for the switching of Mains Circuits. For the switching of voltages up

to the module’s full specication, Secondary Circuit power supplies and the Device Under Test must

be fully isolated from the Mains Circuit and the safety earth.

The host chassis must be correctly installed and be connected to mains or factory safety ground,

please refer to your chassis installation manual.

Diagram Showing Separation Between The Mains Circuit and Secondary Circuit / DUT

For the purposes of this document, a Mains Circuit is an installation classied as Overvoltage

Category II up to 300V. Separation between the Secondary Circuit and Mains Circuit is achieved

by a transformer in which the primary windings are separated from the secondary windings by

reinforced insulation, double insulation, or a screen connected to the protective conductor terminal.

CAUTION - HANDLING OF ELECTROSTATIC-SENSITIVE DEVICES SYMBOL

Certain semiconductor devices used in this equipment are liable to damage due to static voltage.

Observe the following precautions when handling these devices in their unterminated state, or

sub-assemblies containing these devices:

1. Persons removing sub-assemblies from equipment using these devices must be earthed by a

wrist strap and a resistor at the point provided on the equipment.

2. Soldering irons used during the repair operations must be low voltage types with earthed tips and

isolated from the mains voltage by a double insulated transformer.

3. Outer clothing worn must be unable to generate static charges.

4. Printed Circuit Boards (PCBs) tted with these devices must be stored and transported in

anti-static bags.

PXI Switching

Module

Device

Under Test

Power

Supply

Power

Supply

Host Chassis

Secondary Circuit

Mains

Circuit

Mains

Circuit

Mains/Factory

Safety Ground

Page (VIII) VERY HIGH DENSITY MULTIPLEXER MODULE 40-615A

pickering

Page (VIII) 2 AMP 1-POLE UHD MATRIX MODULES 40-575 / 576 / 577 / 578 / 579

pickering

CAUTION - PRODUCT DOCUMENTATION SYMBOL

Suitably qualied & trained users should ensure that the accompanying documentation is fully read

and understood before attempting to install or operate the product.

SAFETY INSTRUCTIONS

All cleaning and servicing requires the equipment to be isolated and disconnected from the power source and user I/O

signals (refer to the Maintenance Section).

• Appropriate manual handling procedures should be followed as dictated by the weight of the individual module or

the combined weight of the modules & chassis.

• Should a fault occur with the module or chassis, immediately isolate and disconnect the incoming power to the

chassis and the user I/O signals.

• Ensure the equipment is installed, operated and maintained by trained and authorised personnel.

• For suitably equipped products in the event of an emergency press the red “emergency stop” button situated on

the front of the unit.

Page 1.1

VERY HIGH DENSITY MULTIPLEXER MODULE 40-615A

pickering SECTION 1 - TECHNICAL SPECIFICATION

SECTION 1 - TECHNICAL SPECIFICATION

pickeringtest.com

PXI Very High Density Multiplexer 40-615A

ISSUE 2.4 APR 2023

Supported by

eBIRST

These test tools simplify fault-ﬁnding by quickly testing the

system and graphically identifying the faulty relay.

For more information go to: pickeringtest.com/ebirst

yVery High Density Multi-Banked Multiplexer

yChoice of 20, 10, 5, 4, 2 or 1 Multiplexers Per

Module

yUp to 168 Switch Points Available with 1 or

2-Pole Switching Formats

yUses High Reliability Pickering Reed Relays

yFast Operating Speed <500 µs

ySwitch up to 150 VDC/100 VAC, 1.0 A with 20 W

Max Power

yVersions Available With Automatic Isolation

Switches To Reduce Capacitive Loading in

Large Systems

yDrivers Supplied for Windows & Linux,

Plus Support for Real-time Systems

ySupported by PXI or LXI Chassis

ySupported by

eBIRST

™

y3 Year Warranty

Available Multiplexer Formats

20 Banks, 8 Channels, 1-Pole

20 Banks, 4 Channels, 2-Pole

10 Banks, 16 Channels, 1-Pole

10 Banks, 8 Channels, 2-Pole

5 Banks, 32 Channels, 1-Pole

5 Banks, 16 Channels, 2-Pole

4 Banks, 40 Channels, 1-Pole

4 Banks, 20 Channels, 2-Pole

2 Banks, 80 Channels, 1-Pole

2 Banks, 40 Channels, 2-Pole

1 Bank, 160 Channels, 1-Pole

1 Bank, 80 Channels, 2-Pole

6 Lower Density Versions

Custom Sizes (100s of combinations)

The 40-615A series of high density multiplexers feature a wide

range of switching conﬁgurations. It is especially useful where

a large number of small multiplexers are required. Typical

applications include signal routing in ATE and data acquisition

systems. User connections are made via a front panel 200-pin

connector.

The 40-615A can be operated as a conventional multiplexer

with break-before-make action when a new channel is selected.

Alternatively, product variants can be supplied that allow

multiple channels to be simultaneously selected.

Model 40-615A channel selection conﬁgurations have been

revised from model 40-615. The 40-615A family defaults to

single channel selection with multiple channel selection

variants deﬁned by use of a sufﬁx.

The 40-615A single pole high density versions include

automatic isolation switching. This connects only the currently

active multiplexer bank to the common terminal, keeping

capacitive loading and leakage current to a minimum in large

multiplexer systems. Larger multiplexers may be constructed

by daisy chaining the common signals from multiple modules.

Automatic isolation switching only applies to single channel

selection mode, for versions with multi channel selection, the

isolation relays are controlled separately from the channel

relays. To prolong contact life of the isolation relays it is

strongly advised that they are cold switched.

The 40-615A is part of a family of high density PXI multiplexer

modules all sharing similar architecture and the same 200-pin

connector, other members include the 40-610 and 40-670A

High Density Multiplexer series.

Front Panel Connector

This product is based on the obsolete Molex LFH series

connector that has been superseded by a Pickering

commissioned form, ﬁt, function equivalent. The new

connector series is 100% compatible with the Molex

connectors allowing either gender of Pickering connector to

mate with the corresponding Molex part without issue.

Page 1.2 VERY HIGH DENSITY MULTIPLEXER MODULE 40-615A

pickering

SECTION 1 - TECHNICAL SPECIFICATION

Very High Density MUX, 40-615A

pickeringtest.com

Overview

• 20 Banks of 4 Channels

• 10 Banks of 8 Channels

• 5 Banks of 16 Channels

• 4 Bank of 20 Channels

• 2 Banks of 40 Channels

• 1 Bank of 80 Channels

• Custom Conﬁgurations

• 20 Banks of 4 Channels

• 10 Banks of 8 Channels

• 5 Banks of 16 Channels

• 4 Banks of 20 Channels

• 2 Banks of 40 Channels

• 1 Bank of 80 Channels

• Custom Conﬁgurations

• 20 Banks of 8 Channels

• 10 Banks of 16 Channels

• 5 Banks of 32 Channels

• 4 Banks of 40 Channels

• 2 Banks of 80 Channels

• 1 Bank of 160 Channels

• Custom Conﬁgurations

Note: Multi-channel selection not available in this

mode

Com

1.1

2.1

Com 1

N.1

1.2

2.2

Com 2

N.2

N-1

Isolation

Switches

Com

2-Pole MUX Mode (high density)

– Available Conﬁgurations

1-Pole MUX Mode (low density)

– Available Conﬁgurations

1-Pole MUX Mode (high density)

– Available Conﬁgurations

PCB Layout for the

40-615A Very High

Density Multiplexer

Module

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Pickering Multiplexer Handbücher

Pickering

Pickering PXI 40-620A Bedienungsanleitung

Pickering

Pickering PXI 40-655 Bedienungsanleitung

Pickering

Pickering SYSTEM 10 Bedienungsanleitung

Pickering

Pickering 60-590 Bedienungsanleitung

Pickering

Pickering PXI Power MUX BRIC 40-571 Bedienungsanleitung

Pickering

Pickering 40-612A Bedienungsanleitung

Pickering

Pickering 40-682A Bedienungsanleitung

Pickering

Pickering 40-658A Bedienungsanleitung

Pickering

Pickering 40-320A Bedienungsanleitung

Pickering

Pickering 40-614C Bedienungsanleitung

Pickering

Pickering 40-850 Bedienungsanleitung

Pickering

Pickering PXI 40-882B Bedienungsanleitung

Pickering

Pickering 40-760 Bedienungsanleitung

Pickering

Pickering 40-655A Bedienungsanleitung

Pickering

Pickering SYSTEM 10 Bedienungsanleitung

Pickering

Pickering 40-756 Bedienungsanleitung

Pickering

Pickering PXI Power MUX BRIC 40-571A Bedienungsanleitung

Pickering

Pickering 40-659A Bedienungsanleitung

Pickering

Pickering PXI 40-883A Bedienungsanleitung

Pickering

Pickering 40-619 Bedienungsanleitung

Pickering

Pickering PXI 40-748 1 Series Bedienungsanleitung

Pickering

Pickering 40-657A Bedienungsanleitung

Pickering

Pickering 40-660A-001 Bedienungsanleitung

Pickering

Pickering 40-616A Bedienungsanleitung

Beliebte Multiplexer Handbücher anderer Marken

Campbell

Campbell AM416 Bedienungsanleitung

Paradyne

Paradyne SIM2000 Bedienungsanleitung

Panasonic

Panasonic WJFS616 - SWITCHER Bedienungsanleitung

Lanex

Lanex TM-77 Bedienungsanleitung

Bosch

Bosch VSS8394/01T Bedienungsanleitung

Quark-Elec

Quark-Elec QK-A035 Bedienungsanleitung

ADTRAN

ADTRAN Frameport 768 Bedienungsanleitung

Elo TouchSystems

Elo TouchSystems E247 Bedienungsanleitung

Paradyne

Paradyne Hotwire 8786 Bedienungsanleitung

RFL Electronics

RFL Electronics 9508D UCC Bedienungsanleitung

Miranda

Miranda AMX-101i Bedienungsanleitung

ShipModul

ShipModul MiniPlex-AIX NMEA-0183 Bedienungsanleitung

GE StoreSafe SDVR-10 Bedienungsanleitung

American Fibertek

American Fibertek MTX-8410C Bedienungsanleitung

ADC

ADC HiGain ELU-319 5E Bedienungsanleitung

Paradyne

Paradyne Hotwire 8774 Bedienungsanleitung

American Fibertek

American Fibertek MTX-8810C-SL Bedienungsanleitung

Viessmann

Viessmann 5229 Bedienungsanleitung