Pilz PNOZ mmc11p Bedienungsanleitung

PNOZ mmc11p

Operating Manual 1002697-EN-03

}Configurable compact control systems PNOZmulti Mini

Preface

This document is a translation of the original document.

All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made

for internal purposes. Suggestions and comments for improving this documentation will be

gratefully received.

Source code from third-party manufacturers or open source software has been used for

some components. The relevant licence information is available on the Internet on the Pilz

homepage.

Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,

SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks

of Pilz GmbH & Co. KG in some countries.

SD means Secure Digital

Contents

Operating Manual PNOZ mmc11p

1002697-EN-03 3

Section 1 Introduction 4

1.1 Validity of documentation 4

1.2 Using the documentation 4

1.3 Definition of symbols 4

Section 2 Overview 6

2.1 Scope of supply 6

2.2 Unit features 6

2.3 Front view 7

Section 3 Safety 8

3.1 Intended use 8

3.2 System requirements 8

3.3 Safety regulations 9

3.3.1 Use of qualified personnel 9

3.3.2 Warranty and liability 9

3.3.3 Disposal 9

3.3.4 For your safety 9

Section 4 Function description 10

4.1 Operation 10

4.2 Input and output data 10

4.3 Assigning the inputs/outputs in the PNOZmulti Configurator to the Ether-

CAT inputs/outputs

4.4 Block diagram 11

Section 5 Installation 12

5.1 General installation guidelines 12

5.2 Dimensions in mm 12

5.3 Connect the base unit and expansion modules 13

Section 6 Commissioning 14

6.1 General wiring guidelines 14

6.2 Connecting the supply voltage 14

6.3 Interface assignment 15

6.4 Download modified project to the PNOZmulti safety system 15

6.5 Preparing for operation 15

6.6 Connection example 16

Section 7 Operation 17

7.1 Messages 17

Section 8 Technical details 18

Section 9 Order reference 20

9.1 Product 20

9.2 Accessories 20

Introduction

Operating Manual PNOZ mmc11p

1002697-EN-03 4

1 Introduction

1.1 Validity of documentation

This documentation is valid for the product PNOZ mmc11p. It is valid until new documenta-

tion is published.

This operating manual explains the function and operation, describes the installation and

provides guidelines on how to connect the product.

1.2 Using the documentation

This document is intended for instruction. Only install and commission the product if you

have read and understood this document. The document should be retained for future ref-

erence.

1.3 Definition of symbols

Information that is particularly important is identified as follows:

DANGER!

This warning must be heeded! It warns of a hazardous situation that poses

an immediate threat of serious injury and death and indicates preventive

measures that can be taken.

WARNING!

This warning must be heeded! It warns of a hazardous situation that could

lead to serious injury and death and indicates preventive measures that can

be taken.

CAUTION!

This refers to a hazard that can lead to a less serious or minor injury plus

material damage, and also provides information on preventive measures

that can be taken.

NOTICE

This describes a situation in which the product or devices could be dam-

aged and also provides information on preventive measures that can be

taken. It also highlights areas within the text that are of particular import-

ance.

Introduction

Operating Manual PNOZ mmc11p

1002697-EN-03 5

INFORMATION

This gives advice on applications and provides information on special fea-

tures.

Overview

Operating Manual PNOZ mmc11p

1002697-EN-03 6

2 Overview

2.1 Scope of supply

}Expansion module PNOZ mmc11p

}Jumper

2.2 Unit features

Using the product PNOZ mmc11p:

Expansion module for connection to a base unit from the configurable control system

PNOZmulti Mini .

The product has the following features:

}Can be configured in the PNOZmulti Configurator

}Network protocols: EtherCAT

}Supports CANopen over EtherCAT (DS301 V4.02 compliant)

}Status indicators for communication with EtherCAT and for errors

}24 virtual inputs and outputs on the control system PNOZmulti can be defined in the

PNOZmulti Configurator for communication with the fieldbus EtherCAT . The number of

inputs and outputs can be extended to 128. Please note that when the extended inputs

and outputs 24 - 127 are used they have different properties (see document entitled

"Communication Interfaces").

}Max. 1 PNOZ mmc11p can be connected to the base unit

}Plug-in connection terminals:

either spring-loaded terminal or screw terminal available as an accessory (see order

reference)

}For details of the PNOZmulti Mini base units that can be connected, please refer to the

document "PNOZmulti System Expansion".

Overview

Operating Manual PNOZ mmc11p

1002697-EN-03 7

2.3 Front view

Legend:

}X1: EtherCAT IN

}X2: EtherCAT OUT

}X4: 0 V, 24 V:

Supply connections

}: Functional earth

}LEDs:

– Power

– Run

– Error

– L/A 1

– L/A 2

is registered trademark and patented technology, licensed by Beckhoff

Automation GmbH, Germany

Safety

Operating Manual PNOZ mmc11p

1002697-EN-03 8

3 Safety

3.1 Intended use

The expansion module PNOZ mmc11p is used for communication between the configur-

able control system PNOZmulti with EtherCAT.

EtherCAT is designed for fast data exchange at field level. The expansion module PNOZ

mmc11p is a passive EtherCAT subscriber (Slave). The basic communication functions

with EtherCAT conform to the system description published by the EtherCAT User Group.

The central controller (master) reads input information from the slaves and writes output in-

formation to the slaves as part of each cycle.

The expansion module may only be connected to a base unit from the configurable control

system PNOZmulti (please refer to the document "PNOZmulti System Expansion" for de-

tails of the base units that can be connected)

The configurable control system PNOZmulti is used for the safety-related interruption of

safety circuits and is designed for use in:

}E-STOP equipment

}Safety circuits in accordance with VDE0113 Part 1 and EN60204-1

The expansion module may not be used for safety-related functions.

Intended use includes making the electrical installation EMC-compliant. The product is de-

signed for use in an industrial environment. It is not suitable for use in a domestic environ-

ment, as this can lead to interference.

The following is deemed improper use in particular:

}Any component, technical or electrical modification to the product

}Use of the product outside the areas described in this manual

}Use of the product outside the technical details (see chapter entitled “Technical De-

tails”)

3.2 System requirements

Please refer to the "Product Modifications PNOZmulti" document in the "Version overview"

section for details of which versions of the base unit and PNOZmulti Configurator can be

used for this product.

Safety

Operating Manual PNOZ mmc11p

1002697-EN-03 9

3.3 Safety regulations

3.3.1 Use of qualified personnel

The products may only be assembled, installed, programmed, commissioned, operated,

maintained and decommissioned by competent persons.

A competent person is someone who, because of their training, experience and current pro-

fessional activity, has the specialist knowledge required to test, assess and operate the

work equipment, devices, systems, plant and machinery in accordance with the general

standards and guidelines for safety technology.

It is the company’s responsibility only to employ personnel who:

}Are familiar with the basic regulations concerning health and safety / accident preven-

tion

}Have read and understood the information provided in this description under "Safety"

}And have a good knowledge of the generic and specialist standards applicable to the

specific application.

3.3.2 Warranty and liability

All claims to warranty and liability will be rendered invalid if

}The product was used contrary to the purpose for which it is intended

}Damage can be attributed to not having followed the guidelines in the manual

}Operating personnel are not suitably qualified

}Any type of modification has been made (e.g. exchanging components on the PCB

boards, soldering work etc.).

3.3.3 Disposal

}When decommissioning, please comply with local regulations regarding the disposal of

electronic devices (e.g. Electrical and Electronic Equipment Act).

3.3.4 For your safety

The unit meets all the necessary conditions for safe operation. However, you should always

ensure that the following safety requirements are met:

}This operating manual only describes the basic functions of the unit. The expanded

functions are described in the PNOZmulti Configurator's online help. Only use these

functions once you have read and understood the documentations.

}Do not open the housing or make any unauthorised modifications.

}Please make sure you shut down the supply voltage when performing maintenance

work (e.g. exchanging contactors).

Function description

Operating Manual PNOZ mmc11p

1002697-EN-03 10

4 Function description

4.1 Operation

The virtual inputs and outputs that are to be transferred via EtherCAT are selected and con-

figured in the PNOZmulti Configurator. The base unit and the expansion module PNOZ

mmc11p are connected via a jumper. After the supply voltage is switched on or the

PNOZmulti control system is reset, the expansion module PNOZ mmc11p is configured and

started automatically.

The connection to EtherCAT is made via the two RJ45 sockets.

LEDs indicate the status of the expansion module on EtherCAT.

The configuration is described in detail in the PNOZmulti Configurator's online help.

4.2 Input and output data

The data is structured as follows:

}Input area

The inputs are defined in the master and transferred to the PNOZmulti. Each input has

a number, e.g. input bit 4 of byte 1 has the number i12.

}Output range

The outputs are defined in the PNOZmulti Configurator. Each output that is used is

given a number there, e.g. o0, o5... The status of output o0 is stored in bit 0 of byte 0;

the status of output o5 is stored in bit 5 of byte 0 etc.

}Output range only: Byte 3

Bits 0 … 4: Status of LEDs on the PNOZmulti

– Bit 0: OFAULT

– Bit 1: IFAULT

– Bit 2: FAULT

– Bit 3: DIAG

– Bit 4: RUN

Bit 5: Data is being exchanged.

Detailed information on data exchange (tables, segments) is available in the document

"Communication Interfaces" in the section entitled "Fieldbus modules".

4.3 Assigning the inputs/outputs in the PNOZmulti Configurator

to the EtherCAT inputs/outputs

Virtual inputs on PNOZmulti Configurator i0 ... I7 i8 ... i15 i16 ... i23

Input data EtherCAT Byte 0: Bits 0 … 7 Byte 1: Bits 0 … 7 Byte 2: Bits 0 … 7

Virtual outputs on PNOZmulti Configurator o0 ... o7 o8 ... o15 o16 ... o23

Output data EtherCAT Byte 0: Bits 0 … 7 Byte 1: Bits 0 … 7 Byte 2: Bits 0 … 7

The number of virtual inputs and outputs can be extended to 128 (see document "Commu-

nication Interfaces" in the section entitled "Fieldbus modules")

Inhaltsverzeichnis

Andere Pilz Steuerungssystem Handbücher

Pilz

Pilz PNOZ mmc2p Bedienungsanleitung

Pilz

Pilz PNOZ m ES 14DO Bedienungsanleitung

Pilz

Pilz PSSu WB S IDN Bedienungsanleitung

Pilz

Pilz PSSu H PLC1 FS SN SD Series Bedienungsanleitung

Pilz

Pilz PSSu E S 2AI I se-T Bedienungsanleitung

Pilz

Pilz PMCprimo C Bedienungsanleitung

Pilz

Pilz PNOZmulti Series Bedienungsanleitung

Pilz

Pilz PSSu H m F DP ETH SD Bedienungsanleitung

Pilz

Pilz PNOZmulti Mini Bedienungsanleitung

Pilz

Pilz PSS u2 ES 4DI Bedienungsanleitung

Pilz

Pilz PNOZmulti Bedienungsanleitung

Pilz

Pilz PSS 3032 Bedienungsanleitung

Pilz

Pilz PNOZ m ES Profinet Bedienungsanleitung

Pilz

Pilz PNOZ ml1p Bedienungsanleitung

Pilz

Pilz PSSuniversal multi PSSu H m F DPsafe SN SD Bedienungsanleitung

Pilz

Pilz PNOZ m ES CC-Link Bedienungsanleitung

Pilz

Pilz PMCprimo MC Bedienungsanleitung

Pilz

Pilz PSS u2 ES 4DO R 8A Bedienungsanleitung

Pilz

Pilz PMCprimo C2 Bedienungsanleitung

Pilz

Pilz PNOZ m ES Profibus Bedienungsanleitung

Pilz

Pilz PSS u2 ES 16DOD 0.5A Bedienungsanleitung

Pilz

Pilz PNOZ m B0 Bedienungsanleitung

Pilz

Pilz PSSu E F 2DOR 8 Bedienungsanleitung

Pilz

Pilz PNOZ mm0.1p Bedienungsanleitung

Beliebte Steuerungssystem Handbücher anderer Marken

Pentair Pool Products

Pentair Pool Products Compool Bedienungsanleitung

ComfortNET

ComfortNET CTK04 Bedienungsanleitung

CAME

CAME G3000 Bedienungsanleitung

Idemia

Idemia MorphoAccess VP MD Bedienungsanleitung

Axis

Axis P1445-LE-3 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN TNC 150 B Bedienungsanleitung

CNC-Step

CNC-Step High-Z T-Series Bedienungsanleitung

Doosan

Doosan DVF Series Bedienungsanleitung

Honeywell

Honeywell KAP 140 Bedienungsanleitung

Honeywell

Honeywell vk41 series Bedienungsanleitung

Cypress

Cypress HHR-3160 Bedienungsanleitung

CAME

CAME GLT40AOS Bedienungsanleitung

Zonex

Zonex GEN II -VVT Benutzerhandbuch

Altronics

Altronics K 9650 Bedienungsanleitung

micro-trak

micro-trak RoadMaster Bedienungsanleitung

micro-trak

micro-trak Calc-An-Acre II Bedienungsanleitung

EMKO

EMKO TRANS-SYNCRO Bedienungsanleitung

Dover

Dover TWG GC ELEMENT II Programmierhandbuch