Pilz PSEN cs1.1n Bedienungsanleitung
PSEN cs1.1n
Operating Manual-22178-EN-05
}PSEN sensor technology
Preface
This document is a translation of the original document.
All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made
for internal purposes. Suggestions and comments for improving this documentation will be
gratefully received.
Source code from third-party manufacturers or open source software has been used for
some components. The relevant licence information is available on the Internet on the Pilz
homepage.
Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,
SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks
of Pilz GmbH & Co. KG in some countries.
SD means Secure Digital
Contents
Operating Manual PSEN cs1.1n
22178-EN-05 3
Introduction 4
Validity of documentation 4
Using the documentation 4
Definition of symbols 4
Safety 5
Intended use 5
Safety regulations 5
Safety assessment 5
Use of qualified personnel 6
Warranty and liability 6
Disposal 6
For your safety 7
Unit features 7
Function description 7
Block diagram 8
Operating distances 8
Lateral and vertical offset 9
Wiring 9
Pin assignment, connector and cable 10
Connection to evaluation devices 10
Teaching in the actuator 12
Installation 12
Adjustment 14
Operation 14
Error display through flashing codes 14
Dimensions in mm 16
Technical details 16
Safety characteristic data 19
Supplementary data 19
Radio approval 19
Order reference 20
System 20
Accessories 20
EC declaration of conformity 21
PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-05 4
Introduction
Validity of documentation
This documentation is valid for the product PSEN cs1.1n. It is valid until new documentation
is published.
This operating manual explains the function and operation, describes the installation and
provides guidelines on how to connect the product.
Using the documentation
This document is intended for instruction. Only install and commission the product if you
have read and understood this document. The document should be retained for future ref-
erence.
Definition of symbols
Information that is particularly important is identified as follows:
DANGER!
This warning must be heeded! It warns of a hazardous situation that poses
an immediate threat of serious injury and death and indicates preventive
measures that can be taken.
WARNING!
This warning must be heeded! It warns of a hazardous situation that could
lead to serious injury and death and indicates preventive measures that can
be taken.
CAUTION!
This refers to a hazard that can lead to a less serious or minor injury plus
material damage, and also provides information on preventive measures
that can be taken.
NOTICE
This describes a situation in which the product or devices could be dam-
aged and also provides information on preventive measures that can be
taken. It also highlights areas within the text that are of particular import-
ance.
PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-05 5
INFORMATION
This gives advice on applications and provides information on special fea-
tures.
Safety
Intended use
Safety function of safety switch:
}2 safety outputs, each of which supply a high signal when the actuator is in the safety
switch's response range.
The safety switch meets the requirements in accordance with:
}EN 60947-5-3 with the actuator PSEN cs1.1 : PDDB
}EN 62061: SIL CL 3
}EN ISO 13849-1: PL e (Cat. 4)
}ENISO14119: Coding level Low, Type4
The safety switch may only be used with the corresponding actuator PSEN cs1.1.
The safety level PL e (Cat. 4 )/SIL CL 3 is only achieved if
}the safety outputs use 2-channel processing.
The following is deemed improper use in particular:
}Any component, technical or electrical modification to the product
}Use of the product outside the areas described in this manual
}Use of the product outside the technical details (see Technical details [ 16]).
NOTICE
EMC-compliant electrical installation
The product is designed for use in an industrial environment. The product
may cause interference if installed in other environments. If installed in other
environments, measures should be taken to comply with the applicable
standards and directives for the respective installation site with regard to in-
terference.
Safety regulations
Safety assessment
Before using a unit it is necessary to perform a safety assessment in accordance with the
Machinery Directive.
PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-05 6
Functional safety is guaranteed for the product as a single component. However, this does
not guarantee the functional safety of the overall plant/machine. In order to achieve the re-
quired safety level for the overall plant/machine, define the safety requirements for the
plant/machine and then define how these must be implemented from a technical and organ-
isational standpoint.
Use of qualified personnel
The products may only be assembled, installed, programmed, commissioned, operated,
maintained and decommissioned by competent persons.
A competent person is a qualified and knowledgeable person who, because of their train-
ing, experience and current professional activity, has the specialist knowledge required. To
be able to inspect, assess and operate devices, systems and machines, the person has to
be informed of the state of the art and the applicable national, European and international
laws, directives and standards.
It is the company’s responsibility only to employ personnel who
}Are familiar with the basic regulations concerning health and safety / accident preven-
tion,
}Have read and understood the information provided in this description under "Safety"
}Have a good knowledge of the generic and specialist standards applicable to the spe-
cific application.
Warranty and liability
All claims to warranty and liability will be rendered invalid if
}The product was used contrary to the purpose for which it is intended
}Damage can be attributed to not having followed the guidelines in the manual
}Operating personnel are not suitably qualified
}Any type of modification has been made (e.g. exchanging components on the PCB
boards, soldering work etc.).
Disposal
}In safety-related applications, please comply with the mission time TM in the safety-re-
lated characteristic data.
}When decommissioning, please comply with local regulations regarding the disposal of
electronic devices (e.g. Electrical and Electronic Equipment Act).
PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-05 7
For your safety
WARNING!
Loss of safety function due to manipulation of the interlocking device
Manipulation of the interlocking device may lead to serious injury and death.
– You should prevent any possibility of the interlocking device being
manipulated through the use of a spare actuator.
– Keep the substitute actuator in a safe place and protect it from unau-
thorised access.
– If spare actuators are used, these must be installed as described in
Installation [ 12].
– If the original actuators are replaced with substitute actuators, the ori-
ginal actuators must be destroyed before disposal.
}Do not remove the connector's protective cap until you are just about to connect the
unit. This will prevent potential contamination.
Unit features
}Transponder technology for presence detection
}Pilz coding type: Coded
}Dual-channel operation
}2 safety outputs
}LED display for:
– State of the actuator
– Supply voltage/fault
}4 directions of actuation
Function description
The safety outputs may have a high or low signal, depending on the position of the actu-
ator.
In a safe condition there is a low signal at the safety outputs.
State of the outputs:
Actuator in the response
range Safety output 12 Safety output 22
Yes High High
No Low Low
PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-05 8
Block diagram
A1 A2
Power
12 22
Receiver Actuator
Operating distances
On
Off
Legend:
}Sao Assured operating distance: 15 mm
}So Typical operating distance: 21 mm
}Sr Typical release distance: 32 mm
}Sar Assured release distance: 40 mm
PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-05 9
Lateral and vertical offset
Lateral offset Vertical offset
[1]
[2]
[3]
[4] [4]
[5]
[6]
Power / Fault
Safety Gate
Input
[4]
[4]
0 10 20
0 10 20
40
-20
-40
20
10
30
-10
-30
0
Legend
[1] Hysteresis
[2] Typical operating distance SO
[3] Typical release distance Sr
[4] Offset in mm
[5] Operating distance in mm
[6] Response range
Wiring
Please note:
}Information given in the "Technical details" must be followed.
}The power supply must meet the regulations for extra low voltages with protective sep-
aration (SELV, PELV).
}The inputs and outputs of the safety switch must have a protective separation to
voltages over 60 VDC.
PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-05 10
INFORMATION
Only use safety relays with a 24 VDC supply voltage. Safety relays with a
wide-range power supply or in AC device versions have internal potential
isolation and are not suitable as evaluation devices.
}The supply voltage to the safety switch must be protected with a 2 A to 4A quick-acting
fuse.
}Ensure the wiring and EMC requirements of IEC 60204-1 are met.
Pin assignment, connector and cable
12
3
5
4
5-pin M12 male connector
PIN
Pin
designation Function Wire colour
1 A1 +24 UB Brown
2 12 Output, channel1 White
3 A2 0 V UB Blue
4 22 Output, channel2 Black
5 - Do not connect Grey
The wire colour also applies for the cable available from Pilz as an accessory.
Connection to evaluation devices
Make sure that the selected evaluation device has the following property:
}OSSD signals are evaluated through 2 channels with feasibility monitoring
Please note:
}Information given in the Technical details [ 16] must be followed.
Andere Handbücher für PSEN cs1.1n
1
Inhaltsverzeichnis
Andere Pilz Sicherheitssensor Handbücher
Pilz
Pilz PSEN ma1.1p-12 Bedienungsanleitung
Pilz
Pilz PSEN cs3.1a/b Bedienungsanleitung
Pilz
Pilz PSEN ma1.4-51 M12/8-0.15m Bedienungsanleitung
Pilz
Pilz PSEN 2.1p-20 Bedienungsanleitung
Pilz
Pilz PNOZ m1p Bedienungsanleitung
Pilz
Pilz PSEN ma1.3a-27 VA Bedienungsanleitung
Pilz
Pilz PSEN 1.2p-20 Bedienungsanleitung
Pilz
Pilz PSEN ma1.3n-20 Bedienungsanleitung
Pilz
Pilz PSEN cs2.2n Bedienungsanleitung
Pilz
Pilz PSEN ma2.1p-10 Bedienungsanleitung
Pilz
Pilz PSEN 1.1b-23 Bedienungsanleitung
Pilz
Pilz PSEN opII3F Series Bedienungsanleitung
Pilz
Pilz PSEN ml b 1.1 Bedienungsanleitung
Pilz
Pilz PSEN cs2.1n Bedienungsanleitung
Pilz
Pilz PSEN 2.2p-21 Bedienungsanleitung
Pilz
Pilz PSEN ma1.3-20 M12/8 VA Bedienungsanleitung
Pilz
Pilz PSEN opII mirror column Series Bedienungsanleitung
Pilz
Pilz PSEN sl-0.5n 2.2 Bedienungsanleitung
Pilz
Pilz PSEN ml sa 1.1 Bedienungsanleitung
Pilz
Pilz PSEN 1.1p-20 Bedienungsanleitung
