Pioneer AVIC-880DVD Bedienungsanleitung

MANUEL D’INSTALLATION

AVIC-880DVD

INSTALLATION MANUAL

ENGLISH FRANÇAIS DEUTSCH ITALIANO NEDERLANDS

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit est

conforme à CEMA.

ENG/MASTER COVER 98 INST

<CRD3982A> 1

CRD3982A_inst_cover 1/6/05 14:28 Page 3

IMPORTANT INFORMATION

ABOUT YOUR NEW NAVIGATION SYSTEM AND THIS MANUAL

• The navigation features of this unit is intended solely as an aid to you in the oper-

ation of your vehicle. It is not a substitute for your attentiveness, judgment and

care when driving.

• Never use this Navigation System to route to hospitals, police stations, or similar

facilities in an emergency. Please call 911.

•Do not operate this Navigation System if doing so in any way will divert your

attention from the safe operation of your vehicle. Traffic restrictions and advi-

sories currently in force should always take precedence over guidance given by

this product. Always obey current traffic restrictions, even if this product pro-

vides contrary advice.

• Certain government laws may restrict the placement and use of navigation sys-

tems in your vehicle. Please comply with all applicable laws and regulations in

the installation and operation of your navigation system.

• This manual explains how to install this Navigation System in your vehicle.

Operation of this Navigation System is explained in the separate “Operation

Manual” or “Hardware Manual” for Navigation System.

• Do not install the display and the navigation unit where it may (i) obstruct the dri-

ver’s vision, (ii) impair the performance of any of the vehicle’s operating systems

of safety features, including airbags, hazard lamp buttons or (iii) impair the dri-

ver’s ability to safely operate the vehicle. In some cases, it may not be possible to

install this unit because of the vehicle type or the shape of the vehicle interior.

ENG/MASTER 96

<CRD3982A> 2

CRD3982A_inst_001_030_Eng 1/6/05 14:33 Page 2

<CRD3982A> 3

IMPORTANT INFORMATION......................1

ABOUT YOUR NEW NAVIGATION

SYSTEM AND THIS MANUAL................1

IMPORTANT SAFEGUARDS .................... 3

PLEASE READ ALL OF THESE

INSTRUCTIONS REGARDING YOUR

NAVIGATION SYSTEM AND RETAIN

THEM FOR FUTURE REFERENCE ...... 3

Connecting the System ............................ 4

WARNING ........................................................ 4

CAUTION ........................................................ 4

-Before installing the unit

-To prevent damage

-Parts supplied

Connecting the system ...................................... 8

-Connecting to the display with 26-pin

input (e.g. AVH-P7600DVD,

AVH-P5700DVD, etc.)

Connecting the power cord (1) .......................... 9

Connecting the power cord (2) ........................ 11

Installation ................................................ 12

WARNING ...................................................... 12

CAUTION ...................................................... 12

To guard against electromagnetic

interference ................................................14

Before installing and fixing ............................ 14

Before using the adhesive tape ........................ 14

Installing the main unit .................................... 15

-Installation notes

-Parts supplied

-CAUTION

-If you install with the left and right sides

of the Navigation Unit parallel to your

vehicle’s forward / backward direction

-When installing the main unit inside the

trunk, on the floor under a seat, etc., using

tapping screws

-CAUTION

-DIN Rear-mount: Installation using the

screw holes on the side of the unit

Installing the GPS antenna .............................. 22

-CAUTION

-Installation notes

-Parts supplied

-When installing the antenna inside the

vehicle (on the rear shelf)

-When installing the antenna outside the

vehicle (on the body)

Installing the Steering remote control ............ 25

-Parts supplied

-Loading the battery

-WARNING

-CAUTION

-WARNING

-Remote control handling notes

-Installing the holders and the steering remote

control

Installing the microphone ................................ 27

-Installation notes

-Parts supplied

-When installing the microphone on the

sun visor

-When installing the microphone on the

steering column

-CAUTION

After installing the unit .......................... 30

ENGLISH ESPAÑOL DEUTSCH FRANÇAIS ITALIANO NEDERLANDS

ENG/MASTER 96

Contents

CRD3982A_inst_001_030_Eng 1/6/05 14:33 Page 3

<CRD3982A> 4

ENG/MASTER 96

IMPORTANT SAFEGUARDS

PLEASE READ ALL OF THESE INSTRUCTIONS REGARDING YOUR NAVIGA-

TION SYSTEM AND RETAIN THEM FOR FUTURE REFERENCE

1. Read this manual fully and carefully before installing your Navigation System.

2. Keep this manual handy for future reference.

3. Pay close attention to all warnings in this manual and follow the instructions care-

fully.

4. This Navigation System may in certain circumstances display erroneous informa-

tion regarding the position of your vehicle, the distance of objects shown on the

screen, and compass directions. In addition, the system has certain limitations,

including the inability to identify one-way streets, temporary traffic restrictions

and potentially unsafe driving areas. Please exercise your own judgment in the

light of actual driving conditions.

5. As with any accessory in your vehicle’s interior, the Navigation System should

not divert your attention from the safe operation of your vehicle. If you experi-

ence difficulty in operating the system or reading the display, please make adjust-

ments while safely parked.

6. Please remember to wear your seat belt at all times while operating your vehicle.

If you are ever in an accident, your injuries can be considerably more severe if

your seat belt is not properly buckled.

• Do not attempt to install or service your Navigation System by yourself.

Installation or servicing of the Navigation System by persons without train-

ing and experience in electronic equipment and automotive accessories may

be dangerous and could expose you to the risk of electric shock or other haz-

ards.

CRD3982A_inst_001_030_Eng 1/6/05 14:33 Page 4

<CRD3982A> 5

ENGLISH ESPAÑOL DEUTSCH FRANÇAIS ITALIANO NEDERLANDS

ENG/MASTER 96

Connecting the System

• Pioneer does not recommend that you install your Navigation System your-

self. We recommend that only authorized Pioneer service personnel, who

have special training and experience in mobile electronics, set up and install

the unit. NEVER SERVICE THE UNIT YOURSELF. Installing or servicing

the unit and its connecting cables may expose you to the risk of electric shock

or other hazards, and can cause damage to the Navigation System that is not

covered by warranty.

• If you decide to perform the installation yourself, and have special training

and experience in the mobile electronics installations, please carefully follow

all of the steps in the Installation Manual.

• Secure all wiring with cable clamps or electrical tape. Do not allow any bare

wiring to remain exposed.

• Do not directly connect the yellow lead of the unit to the vehicle battery. If

the lead is directly connected to the battery, engine vibration may eventually

cause the insulation to fail at the point where the wire passes from the pas-

senger compartment into the engine compartment. If the yellow lead’s insu-

lation tears as a result of contact with metal parts, short-circuiting can occur,

resulting in considerable danger.

• It is extremely dangerous to allow the GPS antenna cable or microphone

cable to become wound around the steering column or shift lever. Be sure to

install the unit, its cables, and wiring away in such a way that they will not

obstruct or hinder driving.

• Make sure that the cables and wires are routed and secured so they will not

interfere with or become caught in any of the vehicle’s moving parts, espe-

cially the steering wheel, shift lever, parking brake, sliding seat tracks, doors,

or any of the vehicle’s controls.

• Do not route wires where they will be exposed to high temperatures. If the

insulation heats up, wires may become damaged, resulting in a short circuit

or malfunction and permanent damage to the product.

• Do not cut the GPS antenna cable to shorten it or use an extension to make it

longer. Altering the antenna cable could result in a short circuit or malfunc-

tion.

CRD3982A_inst_001_030_Eng 1/6/05 14:33 Page 5

Connecting the System

• Do not shorten any leads. If you do, the protection circuit (fuse holder, fuse

resister or filter, etc.) may fail to work properly.

• Never feed power to other electronic products by cutting the insulation of the

power supply lead of the Navigation System and tapping into the lead. The

current capacity of the lead will be exceeded, causing overheating.

ENG/MASTER 96

<CRD3982A> 6

CRD3982A_inst_001_030_Eng 1/6/05 14:33 Page 6

<CRD3982A> 7

Connecting the System

ENGLISH ESPAÑOL DEUTSCH FRANÇAIS ITALIANO NEDERLANDS

ENG/MASTER 96

Before installing the unit

• This unit is for vehicles with a 12-volt battery and negative grounding. Check the battery

voltage of your vehicle before installation.

To prevent damage

• When disconnecting a connector, pull the connector itself. Do not pull the lead, as you

may pull it out of the connector.

• If this unit is installed in a vehicle that does not have an ACC (accessory) position on the

ignition switch, the red lead of the unit should be connected to a terminal coupled with

ignition switch ON/OFF operations. If this is not done, the vehicle battery may be

drained when you are away from the vehicle for several hours.

• To avoid short-circuiting, cover the disconnected lead with insulating tape.

• Attach the connectors of the same color to the corresponding colored port, i.e., yellow

connector to the yellow port, black to black, etc.

• The black lead is ground. Please ground this lead separately from the ground of highcur-

rent products such as power amps.

Do not ground more than one product together with the ground from another product.

For example, you must separately ground any amplifier unit away from the ground of

this unit. Connecting grounds together can cause a fire and/or damage the products if

their grounds became detached.

• When replacing the fuse, be sure to only use a fuse of the rating prescribed on the fuse

holder.

No ACC positionACC position

• To avoid shorts in the electrical sys-

tem, be sure to disconnect the (–) bat-

tery cable before beginning installa-

tion.

CRD3982A_inst_001_030_Eng 1/6/05 14:33 Page 7

Connecting the System

Parts supplied

MicrophoneGPS antenna

26-pin cableConnectorPower cord

ENG/MASTER 96

<CRD3982A> 8

CRD3982A_inst_001_030_Eng 1/6/05 14:33 Page 8

Power cord

Black

This product

Microphone

Yellow

GPS antenna

☞ See page 22.

☞ See page 27.

(e.g. AVH-P7600DVD, AVH-P5700DVD,

AVH-P6600DVD, AVH-P7500DVD,

AVH-P6500DVD, AVD-W6210, AVX-P8DVD)

Not used.

26-pin cable (supplied)

6m (19 ft. 8 in.)

☞ See pages 9-11.

When resetting AV Head Unit or AV

system display

When pressing the reset button of AV Head

Unit or AV system display while Navigation

System and AV Head Unit or AV system dis-

play (AVH-P7600DVD, AVH-P5700DVD,

AVH-P7500DVD, AVH-P6500DVD, AVH-

P6600DVD, AVX-P8DVD) are combined,

make sure that ACC is turned OFF. If the

reset button is pressed while ACC is ON, it

may not work properly.

Display Unit

There may be no voice guidance depending on a com-

bined display unit. In that case, an external speaker

(commercially available) must be connected to the SP-

OUT jack (3.5 ø MINI JACK, 1 W max [8 Ω]) on this

unit’s back.

When combining multi-channel processors, Pioneer

external speaker must be connected to the SP-OUT jack

on the navigation’s back. However, if your display has

the GUIDE SP OUT jack that can output the voice guid-

ance, connect the external speaker to the display.

Connecting the system

Connecting to the display with 26-pin input (e.g. AVH-P7600DVD, AVH-P5700DVD, etc.)

ENGLISH ESPAÑOL DEUTSCH FRANÇAIS ITALIANO NEDERLANDS

ENG/MASTER 96

<CRD3982A> 9

6m (19 ft. 8 in.)

5m (16 ft. 5 in.)

CRD3982A_inst_001_030_Eng 1/6/05 14:33 Page 9

<CRD3982A> 10

Connecting the System

ENG/MASTER 96

Connecting the power cord (1)

Connector

Speed detection circuit lead

Vehicle injection computer

Connection method

Pass the extension cord

and the lead for the

speed detection circuit

through this hole.

Clamp firmly with

needle-nosed pliers.

Close the cover.

Note: The position of the speed

detection circuit depends on the

vehicle model. For details, consult

your authorized Pioneer dealer or

an installation professional. If con-

nection to the speed detection cir-

cuit is too difficult, connect the

separately sold ND-PG1 speed

pulse generator to the pink lead.

Note: The position of the parking

brake switch depends on the vehi-

cle model. For details, consult the

vehicle owner’s manual or dealer.

Connection method

Clamp the parking brake

switch power supply side lead.

Clamp firmly with

needle-nosed pliers.

Power supply side

Ground side

Parking brake switch

Pink (CAR SPEED SIGNAL INPUT)

The navigation system is connected here to detect the dis-

tance the vehicle travels. Always connect the vehicle’s

speed detection circuit or the ND-PG1 speed pulse genera-

tor, sold separately. Failure to make this connection will

increase in the location display.

IMPROPER CONNECTION MAY RESULT IN SERI-

OUS DAMAGE OR INJURY INCLUDING ELECTRI-

CAL SHOCK, AND INTERFERENCE WITH THE

OPERATION OF THE VEHICLE’S ANTILOCK

BRAKING SYSTEM, AUTOMATIC TRANSMIS-

SION AND SPEEDOMETER INDICATION.

Light green

Used to detect the ON/OFF status of the parking brake.

This lead must be connected to the power supply side of

the parking brake switch. If this connection is made

incorrectly or omitted, certain functions of your naviga-

tion system will be unusable.

LIGHT GREEN LEAD AT POWER CON-

NECTOR IS DESIGNED TO DETECT

PARKED STATUS AND MUST BE CON-

NECTED TO THE POWER SUPPLY

SIDE OF THE PARKING BRAKE

SWITCH. IMPROPER CONNECTION

OR USE OF THIS LEAD MAY VIOLATE

APPLICABLE LAW AND MAY RESULT

IN SERIOUS INJURY OR DAMAGE.

CRD3982A_inst_001_030_Eng 1/6/05 14:33 Page 10

Andere Handbücher für AVIC-880DVD

Inhaltsverzeichnis

Sprachen:

Andere Pioneer Auto-Navigationssystem Handbücher

Pioneer

Pioneer AVIC-F9880BT Bedienungsanleitung

Pioneer

Pioneer AVIC-Z1 Bedienungsanleitung

Pioneer

Pioneer AVIC-U250 Bedienungsanleitung

Pioneer

Pioneer AVIC-Z120BT Bedienungsanleitung

Pioneer

Pioneer AVIC-F980DAB-C Gebrauchs- und Pflegehandbuch

Pioneer

Pioneer AVIC-Z810DAB Bedienungsanleitung

Pioneer

Pioneer AVIC-Z1000DAB Bedienungsanleitung

Pioneer

Pioneer AVIC-Z1 Bedienungsanleitung

Pioneer

Pioneer AVIC-9DVD Bedienungsanleitung

Pioneer

Pioneer AVIC Z3 - Navigation System With DVD player Bedienungsanleitung

Pioneer

Pioneer AVIC-Z110BT Bedienungsanleitung

Pioneer

Pioneer AVIC-HD3 Bedienungsanleitung

Pioneer

Pioneer AVIC-F30BT Betriebsanleitung

Pioneer

Pioneer F500BT - AVIC - Navigation System Bedienungsanleitung

Pioneer

Pioneer AVIC N2 - Navigation System With DVD player Bedienungsanleitung

Pioneer

Pioneer AVIC-D3 - Navigation System With DVD Player Bedienungsanleitung

Pioneer

Pioneer AVIC-EV01 Bedienungsanleitung

Pioneer

Pioneer CNDV-50MTP Bedienungsanleitung

Pioneer

Pioneer AVIC U310BT - Navigation System With CD... Bedienungsanleitung

Pioneer

Pioneer AVIC-Z910DAB Bedienungsanleitung

Pioneer

Pioneer AVIC-F80BT Bedienungsanleitung

Pioneer

Pioneer AVIC-EVO1-OC2-MTB Bedienungsanleitung

Pioneer

Pioneer AVIC-Z150BH Betriebsanleitung

Pioneer

Pioneer AVIC-F220 Bedienungsanleitung

Beliebte Auto-Navigationssystem Handbücher anderer Marken

Clarion

Clarion Navigation In-Car Entertainment Bedienungsanleitung

Rosen

Rosen DP-1001 Bedienungsanleitung

Alpine

Alpine INE-W970HD Bedienungsanleitung

Blaupunkt

Blaupunkt TravelPilot DX-N Bedienungsanleitung

Sanyo

Sanyo NVM-4030 - Easy Street - Automotive GPS... Bedienungsanleitung

AvMap

AvMap Geosat 2C Bedienungsanleitung

Eonon

Eonon GE01B Bedienungsanleitung

Nextar

Nextar M3-MX - Automotive GPS Receiver Bedienungsanleitung

Furrion

Furrion NV2200 Bedienungsanleitung

Mio

Mio MOOV 200-Series Bedienungsanleitung

Prestigio

Prestigio GeoVision 5150 Bedienungsanleitung

Magellan

Magellan Maestro 4210 - Automotive GPS Receiver Konfigurationshandbuch

Garmin

Garmin StreetPilot c510 Bedienungsanleitung

Garmin

Garmin nüvi 2200 Bedienungsanleitung

Garmin

Garmin 2610/2650 Bedienungsanleitung

Mazda

Mazda 107006AN Bedienungsanleitung

Toyota

Toyota TNS600 Bedienungsanleitung

Toyota

Toyota TNS 200 Bedienungsanleitung