Pioneer AVIC-D1 Bedienungsanleitung
ENG/MASTER COVER 98 INST
AVIC-D1
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est
conforme à CEMA.
INSTALLATION MANUAL
MANUEL D’INSTALLATION
English Français
<CRD3983A> 1
1
IMPORTANT INFORMATION
ABOUT YOUR NEW NAVIGATION SYSTEM AND THIS MANUAL
• The navigation features of this product (and rear view camera option if pur-
chased) is intended solely as an aid to you in the operation of your vehicle. It is
not a substitute for your attentiveness, judgment and care when driving.
• Never use this navigation system to route to hospitals, police stations, or similar
facilities in an emergency, Please call 911.
• Do not operate this navigation system (or the rear view camera option if pur-
chased) if doing so in any way will divert your attention from the safe operation
of your vehicle. Traffic restrictions and advisories currently in force should
always take precedence over guidance given by this product. Always obey current
traffic restrictions, even if this product provides contrary advice.
• Certain government laws may restrict the placement and use of navigation sys-
tems in your vehicle. Please comply with all applicable laws and regulations in
the installation and operation of your navigation system.
• This manual explains how to install this navigation system in your vehicle.
Operation of this navigation system is explained in the separate “Operation
Manual” or “Hardware Manual” for navigation system.
• Do not install this product where it may (i) obstruct the driver’s vision, (ii) impair
the performance of any of the vehicle’s operating systems of safety features,
including airbags, hazard lamp buttons or (iii) impair the driver’s ability to safely
operate the vehicle. In some cases, it may not be possible to install this product
because of the vehicle type or the shape of the vehicle interior.
ENG/MASTER 96
<CRD3983A> 2
<CRD3983A> 3
English Español Deutsch Français Italiano Nederlands
IMPORTANT INFORMATION .................... 1
ABOUT YOUR NEW NAVIGATION
SYSTEM AND THIS MANUAL .............. 1
IMPORTANT SAFEGUARDS .................... 3
PLEASE READ ALL OF THESE
INSTRUCTIONS REGARDING
YOUR NAVIGATION
SYSTEM AND RETAIN THEM
FOR FUTURE REFERENCE .................... 3
Connecting the System ............................ 4
-Before installing this product
-To prevent damage
-Parts supplied
Connecting the system ...................................... 7
Connecting the power cord (1) .......................... 9
Connecting the power cord (2) ........................ 11
When connecting to separately sold power
amp .......................................................... 13
When connecting a Rear view camera ............ 15
When connecting the external video component
and the display .......................................... 16
-When using a display connected to rear video
output
Installation ................................................ 17
To guard against electromagnetic
interference .............................................. 18
Before installing .............................................. 18
Installing this product ...................................... 19
-Installation notes
-Parts supplied
-DIN Front/Rear-mount
-DIN Front-mount
-DIN Rear-mount
Installing the GPS antenna .............................. 23
-Installation notes
-Parts supplied
-When installing the antenna inside the vehi-
cle (on the rear shelf)
-When installing the antenna outside the vehi-
cle (on the body)
After Installing this product.................... 26
2
ENG/MASTER 96
Contents
<CRD3983A> 4
ENG/MASTER 96
IMPORTANT SAFEGUARDS
3
PLEASE READ ALL OF THESE INSTRUCTIONS REGARDING YOUR
NAVIGATION SYSTEM AND RETAIN THEM FOR FUTURE REFERENCE
1. Read this manual fully and carefully before installing your navigation system.
2. Keep this manual handy for future reference.
3. Pay close attention to all warnings in this manual and follow the instructions care-
fully.
4. This navigation system may in certain circumstances display erroneous informa-
tion regarding the position of your vehicle, the distance of objects shown on the
screen, and compass directions. In addition, the system has certain limitations,
including the inability to identify one-way streets, temporary traffic restrictions
and potentially unsafe driving areas. Please exercise your own judgment in the
light of actual driving conditions.
5. As with any accessory in your vehicle’s interior, the navigation system should not
divert your attention from the safe operation of your vehicle. If you experience
difficulty in operating the system or reading the display, please make adjustments
while safely parked.
6. Please remember to wear your seat belt at all times while operating your vehicle.
If you are ever in an accident, your injuries can be considerably more severe if
your seat belt is not properly buckled.
Do not attempt to install or service your navigation system by yourself.
Installation or servicing of the navigation system by persons without training and
experience in electronic equipment and automotive accessories may be dangerous
and could expose you to the risk of electric shock or other hazards.
<CRD3983A> 5
English Español Deutsch Français Italiano Nederlands
4
ENG/MASTER 96
Connecting the System
• Pioneer does not recommend that you install your navigation system yourself. We
recommend that only authorized Pioneer service personnel, who have special train-
ing and experience in mobile electronics, set up and install this product. NEVER
SERVICE THIS PRODUCT YOURSELF. Installing or servicing this product and
its connecting cables may expose you to the risk of electric shock or other hazards,
and can cause damage to the navigation system that is not covered by warranty.
• If you decide to perform the installation yourself, and have special training and
experience in the mobile electronics installations, please carefully follow all of the
steps in the Installation Manual.
• Secure all wiring with cable clamps or electrical tape. Do not allow any bare wiring
to remain exposed.
• Do not directly connect the yellow lead of this product to the vehicle battery. If the
lead is directly connected to the battery, engine vibration may eventually cause the
insulation to fail at the point where the wire passes from the passenger compart-
ment into the engine compartment. If the yellow lead’s insulation tears as a result
of contact with metal parts, short-circuiting can occur, resulting in considerable
danger.
• It is extremely dangerous to allow the GPS antenna cable to become wound around
the steering column or shift lever. Be sure to install this product, its cables, and
wiring away in such a way that they will not obstruct or hinder driving.
• Make sure that the cables and wires are routed and secured so they will not inter-
fere with or become caught in any of the vehicle’s moving parts, especially the
steering wheel, shift lever, parking brake, sliding seat tracks, doors, or any of the
vehicle’s controls.
• Do not route wires where they will be exposed to high temperatures. If the insula-
tion heats up, wires may become damaged, resulting in a short circuit or malfunc-
tion and permanent damage to this product.
• Do not cut the GPS antenna cable to shorten it or use an extension to make it
longer. Altering the antenna cable could result in a short circuit or malfunction.
• Do not shorten any leads. If you do, the protection circuit (fuse holder, fuse resister
or filter, etc.) may fail to work properly.
• Never feed power to other electronic products by cutting the insulation of the
power supply lead of the navigation system and tapping into the lead. The current
capacity of the lead will be exceeded, causing overheating.
• The black lead is ground. Please ground this lead separately from the ground of
high-current products such as power amps.
Do not ground more than one product together with the ground from another
product. For example, you must separately ground any amplifier unit away from
the ground of this product. Connecting grounds together can cause a fire and/or
damage the products if their grounds became detached.
5
Connecting the System
Before installing this product
• This product is for vehicles with a 12-volt battery and negative grounding. Check the
battery voltage of your vehicle before installation.
To prevent damage
When replacing the fuse, be sure to only use a fuse of the rating prescribed on the fuse holder.
• When disconnecting a connector, pull the connector itself. Do not pull the lead, as you
may pull it out of the connector.
• This product cannot be installed in a vehicle that does not have an ACC (accessory)
position on the ignition switch.
• To avoid short-circuiting, cover the disconnected lead with insulating tape. It is especial-
ly important to insulate all unused speaker leads, which if left uncovered may cause a
short circuit.
• Attach the connectors of the same color to the corresponding colored port, i.e., blue con-
nector to the blue port, black to black, etc.
• Refer to the owner’s manual for details on connecting the power amp and other units,
then make connections accordingly.
• Since a unique BPTL circuit is employed, do not directly ground the ≠side of the
speaker lead or connect the ≠sides of the speaker leads together. Be sure to connect the
≠side of the speaker lead to the ≠side of the speaker lead on this product.
• If the RCA pin jack on this product will not be used, do not remove the caps attached to
the end of the connector.
• When connecting the blue lead to the auto antenna and using the auto antenna function,
the vehicle’s antenna can be stowed by following the instructions below.
– In the INITIAL menu, select “RADIO” for “AUTO ANTENNA” and change the
source from radio to another source
– Turn the source off
– Turn off the ignition switch (ACC OFF)
For more detailed information on changing the “AUTO ANTENNA” mode, refer to
“Switching the auto antenna setting” in the “Operation Manual”.
No ACC positionACC position
O
N
S
T
A
R
T
O
F
F
A
C
C
O
N
S
T
A
R
T
O
F
F
• To avoid shorts in the electrical sys-
tem, be sure to disconnect the (–)
battery cable before beginning
installation.
ENG/MASTER 96
<CRD3983A> 6
<CRD3983A> 7
English Español Deutsch Français Italiano Nederlands
6
ENG/MASTER 96
• Never connect speakers with an output rating of less than 50 W channel or impedance
outside of the 4 ohms to 8 ohms specifications to your navigation system. Connecting
speakers with output and/or impedance values other than those noted here may result in
the speakers catching fire, emitting smoke, or becoming damaged.
• When the ignition switch is turned on (ACC ON), a control signal is output through the
blue/white lead. Connect to an external power amp’s system remote control terminal
(max. 300 mA 12 V DC). The control signal is output through the blue/white lead, even
if the audio source is switched off.
• When an external power amp is being used with this system, be sure not to connect the
blue lead to the amp’s power terminal. Likewise, do not connect the blue lead to the
power terminal of the auto antenna. Such connection could cause excessive current drain
and malfunction as well as damage to the auto antenna of the vehicle.
Parts supplied
RCA connector
GPS antennaExtension lead
(for speed signal)
Extension lead
(for reverse signal)
ConnectorPower cordThis product
<CRD3983A> 8
7
Connecting the System
ENG/MASTER 96
Connecting the system
Blue
Blue
*1
Hide-away XM tuner
(GEX-P10XMT)
(sold separately)
Light gray
5 m (16 ft. 5 in.)
GPS antenna
Blue
IP-BUS cable
(supplied with XM tuner)
Black
*2
Black
Black
XM DATA cable
(supplied with XM tuner)
•When combining this product with GEX-P10XMT
(sold separately), this connection must be required.
•When installing the XM tuner in the trunk, etc.,
the optional cable (e.g. CD-600DC) (sold separately)
is required.
Black
Antenna jack
WIRED REMOTE
Please see the Instruction Manual for
the Wired Remote Control (sold separately).
Power cord
RCA connector
This product
Note:
The XM tuner will not receive XM Radio
service when you drive outside of the XM’s
coverage area. When the XM tuner is not
used, connect the IP-BUS cable*1 directly
to this product*2.
☞ See Page 9 to 12.
☞ See Page 13 to 16.
8
ENG/MASTER 96
English Español Deutsch Français Italiano Nederlands
<CRD3983A> 9
Multi-CD player
AV-BUS cable
(supplied with TV tuner)
IP-BUS cable
IP-BUS cable
(supplied with TV tuner)
(sold separately)
Black
Blue
*1
Blue
Hide-away TV tuner
(e.g. GEX-P6400TV)
(sold separately)
ner
)
)
Black
• To avoid the risk of accident and the potential
violation of applicable laws, this product
should never be used while the vehicle is being
driven except for Navigation purposes. And,
also Rear Displays should not be in a location
where it is a visible distraction to the driver.
• In some countries or states the viewing of
images on a display inside a vehicle, even by
persons other than the driver, may be illegal.
Where such regulations apply, they must be
obeyed, and this product’s rear video output
features should not be used.
9
Connecting the System
ENG/MASTER 96
<CRD3983A> 10
Connecting the power cord (1)
Fuse holder
Yellow
To terminal always supplied
with power regardless of
ignition switch position.
Red
To electric terminal controlled
by ignition switch (12 V DC)
ON/OFF.
Black (ground)
To vehicle (metal) body.
Orange/white
To lighting switch terminal.
Fuse resistor
Fuse resistor
With a 2 speaker system, do not connect
anything to the speaker leads that are not
connected to speakers.
This product
White
White/black
Gray
Gray/black
Green
Green/black
Violet
Violet/black
Front speaker
Rear speaker
Front speaker
Rear speaker
Left Right
+
≠
+
≠
+
≠
+
≠
Note:
When a subwoofer is connected to this product instead
of a rear speaker, change the rear output setting in
the Initial Setting. (Refer to the Operation Manual.)
The subwoofer output of this product is monaural.
Andere Handbücher für AVIC-D1
3
Inhaltsverzeichnis
Sprachen:
Andere Pioneer Auto-Navigationssystem Handbücher
Pioneer
Pioneer AVIC-HD3 Bedienungsanleitung
Pioneer
Pioneer AVIC-U260 Bedienungsanleitung
Pioneer
Pioneer AVIC-N3 Bedienungsanleitung
Pioneer
Pioneer AVIC-HD1BT Bedienungsanleitung
Pioneer
Pioneer AVIC-F940BT Bedienungsanleitung
Pioneer
Pioneer AVIC-F80BT Bedienungsanleitung
Pioneer
Pioneer AVIC-N3 Bedienungsanleitung
Pioneer
Pioneer AVIC-Z1 Gebrauchs- und Pflegehandbuch
Pioneer
Pioneer AVIC-F40BT Bedienungsanleitung
Pioneer
Pioneer AVIC-HD3 Bedienungsanleitung
Pioneer
Pioneer T1000-20496 Bedienungs- und Wartungshandbuch
Pioneer
Pioneer CA-R-CG.001 Bedienungsanleitung
Pioneer
Pioneer AVIC-80DVD Bedienungsanleitung
Pioneer
Pioneer AVIC-Z6110BT Bedienungsanleitung
Pioneer
Pioneer AVIC-Z2 - Navigation System With DVD player Bedienungsanleitung
Pioneer
Pioneer AVIC-Z610BT Bedienungsanleitung
Pioneer
Pioneer AVIC N2 - Navigation System With DVD player Bedienungsanleitung
Pioneer
Pioneer CNDV-40R Bedienungsanleitung
Pioneer
Pioneer AVIC N1 - Navigation System With DVD player Bedienungsanleitung
Pioneer
Pioneer AVIC-F8430BT Bedienungsanleitung
Beliebte Auto-Navigationssystem Handbücher anderer Marken
Clarion
Clarion Navigation In-Car Entertainment Bedienungsanleitung
Rosen
Rosen DP-1001 Bedienungsanleitung
Alpine
Alpine INE-W970HD Bedienungsanleitung
Skoda
Skoda AMUNDSEN+ Bedienungsanleitung
Blaupunkt
Blaupunkt TravelPilot DX-N Bedienungsanleitung
Sanyo
Sanyo NVM-4030 - Easy Street - Automotive GPS... Bedienungsanleitung
Prestigio
Prestigio GeoVision 5150 Bedienungsanleitung
Hummer
Hummer 2006 H3 Bedienungsanleitung
Magellan
Magellan Maestro 4210 - Automotive GPS Receiver Konfigurationshandbuch
Garmin
Garmin StreetPilot c510 Bedienungsanleitung
Garmin
Garmin nüvi 2200 Bedienungsanleitung
Garmin
Garmin 2610/2650 Bedienungsanleitung