Pioneer AVIC-HD1BT Bedienungsanleitung

MANUEL D’INSTALLATION

INSTALLATION MANUAL

AVIC-HD1BT

This product conforms to new cord colours.

Los colores de los cables de este producto se confor-

man con un nuevo código de colores.

Dieses Produkt entspricht den neuen kabelfarben.

Le code de couleur des câbles utilisé pour ce produit est

nouveau.

Questo prodotto è conforme ai nuovi codici colori.

De kleuren van de snoeren van dit toestel zijn gewijzigd.

English Español Deutsch Français Italiano Nederlands

IMPORTANT INFORMATION

ABOUT YOUR NEW NAVIGATION SYSTEM AND THIS MANUAL

• The navigation features of this navigation system (and rear view camera option if

purchased) is intended solely as an aid to you in the operation of your vehicle. It

is not a substitute for your attentiveness, judgement and care when driving.

• Never use this navigation system to route to hospitals, police stations, or similar

facilities in an emergency. Please call the appropriate emergency number.

• Do not operate this navigation system (or the rear view camera option if pur-

chased) if doing so in any way will divert your attention from the safe operation

of your vehicle. Traffic restrictions and advisories currently in force should

always take precedence over guidance given by this navigation system. Always

obey current traffic restrictions, even if this navigation system provides contrary

advice.

• This manual explains how to install this navigation system in your vehicle.

Operation of this navigation system is explained in the separate Operation

Manual or Hardware Manual for the navigation system.

• Do not install the navigation system where it may (i) obstruct the driver’s vision,

(ii) impair the performance of any of the vehicle’s operating systems of safety

features, including airbags, hazard lamp buttons or (iii) impair the driver’s ability

to safely operate the vehicle. In some cases, it may not be possible to install this

navigation system because of the vehicle type or the shape of the vehicle interior.

English Español Deutsch Français Italiano Nederlands

IMPORTANT INFORMATION .................... 1

ABOUT YOUR NEW NAVIGATION

SYSTEM AND THIS MANUAL .............. 1

IMPORTANT SAFEGUARDS .................... 3

PLEASE READ ALL OF THESE

INSTRUCTIONS REGARDING

YOUR NAVIGATION

SYSTEM AND RETAIN THEM

FOR FUTURE REFERENCE .................... 3

Connecting the System ............................ 4

-Before installing this navigation system

-To prevent damage

-Parts supplied

Connecting the system ...................................... 7

Connecting the power cord (1) .......................... 9

Connecting the power cord (2) ........................ 11

When connecting to separately sold power

amp .......................................................... 13

When connecting a rear view camera ............ 15

When connecting the external video component

.................................................................. 16

When connecting the external unit featuring video

source ........................................................16

When connecting the rear display ....................17

-When using a rear display connected to rear

video output

Installation ................................................ 18

To guard against electromagnetic

interference .............................................. 19

Before installing .............................................. 19

Installing this navigation system...................... 20

-Installation notes

-Parts supplied

-Installation using the screw holes on the side

of the navigation unit

Installing the GPS aerial .................................. 23

-Installation notes

-Parts supplied

-When installing the aerial inside the vehicle

(on the rear shelf)

-When installing the aerial outside the vehicle

(on the body)

Installing the microphone..................................26

-Parts supplied

-Mounting on the sun visor

-Installation on the steering column

Adjusting the microphone angle ......................27

After Installing this Navigation System

.............................................................. 28

Contents

IMPORTANT SAFEGUARDS

PLEASE READ ALL OF THESE INSTRUCTIONS REGARDING YOUR

NAVIGATION SYSTEM AND RETAIN THEM FOR FUTURE REFERENCE

1. Read this manual fully and carefully before installing your navigation system.

2. Keep this manual handy for future reference.

3. Pay close attention to all warnings in this manual and follow the instructions care-

fully.

4. This navigation system may in certain circumstances display erroneous informa-

tion regarding the position of your vehicle, the distance of objects shown on the

screen, and compass directions. In addition, the system has certain limitations,

including the inability to identify one-way streets, temporary traffic restrictions

and potentially unsafe driving areas. Please exercise your own judgement in the

light of actual driving conditions.

5. As with any accessory in your vehicle’s interior, the navigation system should not

divert your attention from the safe operation of your vehicle. If you experience

difficulty in operating the system or reading the display, please make adjustments

while safely parked.

6. Please remember to wear your seat belt at all times while operating your vehicle.

If you are ever in an accident, your injuries can be considerably more severe if

your seat belt is not properly fastened.

7. Certain countries laws may restrict the placement and use of navigation systems

in your vehicle. Please comply with all applicable laws and regulations in the

installation and operation of your navigation system.

Do not attempt to install or service your navigation system by yourself. Installation or

servicing of the navigation system by persons without training and experience in elec-

tronic equipment and automotive accessories may be dangerous and could expose you

to the risk of electric shock or other hazards.

English Español Deutsch Français Italiano Nederlands

Connecting the System

Pioneer does not recommend that you install your navigation system yourself. We

recommend that only authorised Pioneer service personnel, who have special training

and experience in mobile electronics, set up and install this navigation system.

NEVER SERVICE THIS NAVIGATION SYSTEM YOURSELF. Installing or ser-

vicing this navigation system and its connecting cables may expose you to the risk of

electric shock or other hazards, and can cause damage to the navigation system that

is not covered by warranty.

• If you decide to perform the installation yourself, and have special training and

experience in the mobile electronics installations, please carefully follow all of the

steps in the Installation Manual.

• Secure all wiring with cable clamps or electrical tape. Do not allow any bare wiring

to remain exposed.

• Do not directly connect the yellow lead of this navigation system to the vehicle bat-

tery. If the lead is directly connected to the battery, engine vibration may eventual-

ly cause the insulation to fail at the point where the wire passes from the passenger

compartment into the engine compartment. If the yellow lead’s insulation tears as a

result of contact with metal parts, short-circuiting can occur, resulting in consider-

able danger.

• It is extremely dangerous to allow the GPS aerial cable or microphone cable to

become wound around the steering column or gearstick. Be sure to install this navi-

gation system, its cables, and wiring away in such a way that they will not obstruct

or hinder driving.

• Make sure that the cables and wires are routed and secured so they will not inter-

fere with or become caught in any of the vehicle’s moving parts, especially the

steering wheel, gearstick, handbrake, sliding seat tracks, doors, or any of the vehi-

cle’s controls.

• Do not route wires where they will be exposed to high temperatures. If the insula-

tion heats up, wires may become damaged, resulting in a short circuit or malfunc-

tion and permanent damage to the navigation system.

• Do not cut the GPS aerial cable to shorten it or use an extension to make it longer.

Altering the aerial cable could result in a short circuit or malfunction.

• Do not shorten any leads. If you do, the protection circuit (fuse holder, fuse resister

or filter, etc.) may fail to work properly.

• Never feed power to other electronic products by cutting the insulation of the

power supply lead of the navigation system and tapping into the lead. The current

capacity of the lead will be exceeded, causing overheating.

• The black lead is earth. Please earth this lead separately from the earth of high-

current products such as power amps. Do not earth more than one product togeth-

er with the earth from another product. For example, you must separately earth

any amplifier unit away from the earth of this navigation system. Connecting

earths together can cause a fire and/or damage the products if their earths became

detached.

Connecting the System

Before installing this navigation system

• This navigation system is for vehicles with a 12-volt battery and negative earthing.

Check the battery voltage of your vehicle before installation.

To prevent damage

• When disconnecting a connector, pull the connector itself. Do not pull the lead, as you

may pull it out of the connector.

• This navigation system cannot be installed in a vehicle that does not have an ACC

(accessory) position on the ignition switch.

• To avoid short-circuiting, cover the disconnected lead with insulating tape. It is especial-

ly important to insulate all unused speaker leads, which if left uncovered may cause a

short circuit.

• Attach the connectors of the same colour to the corresponding coloured port, i.e., blue

connector to the blue port, black to black, etc.

• Refer to the owner’s manual for details on connecting the power amp and other units,

then make connections accordingly.

• Since a unique BPTL circuit is employed, do not directly earth the ≠side of the speaker

lead or connect the ≠sides of the speaker leads together. Be sure to connect the ≠side

of the speaker lead to the ≠side of the speaker lead on this navigation system.

• If the RCA pin jack on this navigation system will not be used, do not remove the caps

attached to the end of the connector.

• When the “Auto ANT” mode is set to “Radio”, the vehicle’s aerial can be stowed by

following the instructions below.

– Change the source from radio (AM or FM) to another source

– Turn the source off

– Turn off the ignition switch (ACC OFF)

• If the “Auto ANT” mode is set to “Power”, the vehicle’s aerial can be stowed only

when the ignition switch is turned off (ACC OFF).

No ACC positionACC position

• To avoid shorts in the electrical sys-

tem, be sure to disconnect the (–)

battery cable before beginning

installation.

English Español Deutsch Français Italiano Nederlands

• Never connect speakers with an output rating of less than 50 W channel or impedance

outside of the 4 ohms to 8 ohms specifications to your navigation system. Connecting

speakers with output and/or impedance values other than those noted here may result in

the speakers catching fire, emitting smoke, or becoming damaged.

• When the ignition switch is turned on (ACC ON), a control signal is output through the

blue/white lead. Connect to an external power amp’s system remote control terminal

(max. 300 mA 12 V DC). The control signal is output through the blue/white lead, even

if the audio source is switched off.

• When an external power amp is being used with this system, be sure not to connect the

blue lead to the amp’s power terminal. Likewise, do not connect the blue lead to the

power terminal of the auto aerial. Such connection could cause excessive current drain

and malfunction as well as damage to the auto aerial of the vehicle.

Parts supplied

MicrophoneRCA connector 2

(CONNECTOR 2)

<☞

See Page 7, 12, 15, 17

RCA connector 1

(CONNECTOR 1)

<☞See Page 10, 13, 16>

GPS aerialExtension lead

(for speed signal)

Extension lead

(for reverse signal)

ConnectorPower cord

<☞See Page 9, 11, 15>

The navigation unit

Connecting the System

Connecting the system

AV-BUS cable

(supplied with TV tuner)

IP-BUS cable

(supplied with TV tuner)

Black

Bluetooth unit (ND-BT1)

Aerial

jack

Vehicle

aerial

The navigation unit

RCA connector 2

20 cm

Red

Hide-away TV tuner

(e.g. GEX-P5700TVP)

(sold separately)

Light grey

GPS aerial

WIRED REMOTE INPUT

Please see the Instruction

Manual for the Wired

Remote Control Adapters

(sold separately).

Blue

Not used.

Microphone input

Microphone

(supplied)

Blue

EXTENSION port

Not used. Not used.

• To avoid the risk of accident and

the potential violation of applicable

laws, this navigation system should

never be used while the vehicle is

being driven except for navigation

purposes. Also Rear Displays should

not be in a location where it is a visi-

ble distraction to the driver.

• In some countries the viewing of

images on a display inside a vehicle

even by persons other than the dri-

ver may be illegal. Where such reg-

ulations apply they must be obeyed

and this navigation system’s video

source or TV features should not be

used.

English Español Deutsch Français Italiano Nederlands

Dock connector port

iPod with

Dock Connector

iPod adapter

(e.g. CD-IB100II)

(sold separately)

Black

IP-BUS cable

(supplied with iPod adapter)

Multi-CD player

(sold separately)

Blue

Connecting the System

Connecting the power cord (1)

Connect leads of the same

colour to each other.

Cap (*1)

When not using this terminal,

do not remove the cap.

ISO connector

Fuse (10 A)

Yellow (*2)

To terminal always supplied

with power regardless of

ignition switch position.

Red (*4)

To electric terminal controlled

by ignition switch (12 V DC)

ON/OFF.

Yellow (*3)

Back-up

(or accessory)

Red (*5)

Accessory

(or back-up)

Black (earth)

To vehicle (metal) body.

Orange/white

To lighting switch terminal.

Note:

In some vehicles, the ISO connector

may be divided into two. In this case,

be sure to connect to both connectors.

Note:

Depending on the kind of vehicle, the

function of *3 and *5 may be different.

In this case, be sure to connect *2 to *5

and *4 to *3.

Speaker leads

White: Front left +

White/black: Front left ≠

Grey: Front right +

Grey/black: Front right ≠

Green: Rear left +or Subwoofer +(*9)

Green/black: Rear left ≠or Subwoofer ≠(*9)

Violet: Rear right +or Subwoofer +(*9)

Violet/black: Rear right ≠or Subwoofer ≠(*9)

Yellow/black

If the vehicle can send a mute signal to this terminal,

the mute function can be activated on this navigation

system when the terminal is connected to *8.

Note:

When a subwoofer (*9) is connected to this naviga-

tion system instead of a rear speaker, change the

rear output setting in the Initial Setting. (Refer to

the Operation Manual.) The subwoofer output of

this navigation system is monaural.

When replacing the fuse, be sure to only use a

fuse of the rating prescribed on the fuse holder.

Andere Handbücher für AVIC-HD1BT

Inhaltsverzeichnis

Sprachen:

Andere Pioneer Auto-Navigationssystem Handbücher

Pioneer

Pioneer CNDV-40MT Bedienungsanleitung

Pioneer

Pioneer AVIC-Z2 - Navigation System With DVD player Bedienungsanleitung

Pioneer

Pioneer CNDV-21 Bedienungsanleitung

Pioneer

Pioneer AVIC-S2 Bedienungsanleitung

Pioneer

Pioneer AVIC-HD3 Bedienungsanleitung

Pioneer

Pioneer AVIC-Z910DAB Bedienungsanleitung

Pioneer

Pioneer AVIC-Z110BT Bedienungsanleitung

Pioneer

Pioneer AVIC-F910BT Betriebsanleitung

Pioneer

Pioneer AVIC-F160-2 Bedienungsanleitung

Pioneer

Pioneer AVIC-EVO1-PL2-VAL Bedienungsanleitung

Pioneer

Pioneer AVIC-F8430BT Bedienungsanleitung

Pioneer

Pioneer AVIC-U260 Bedienungsanleitung

Pioneer

Pioneer AVIC-F220 Betriebsanleitung

Pioneer

Pioneer AVIC-F60BT Bedienungsanleitung

Pioneer

Pioneer AVIC-F88DAB Bedienungsanleitung

Pioneer

Pioneer Super Tuner IIID AVIC-F700BT Bedienungsanleitung

Pioneer

Pioneer AVIC-EV01 Bedienungsanleitung

Pioneer

Pioneer AVIC-F10BT Bedienungsanleitung

Pioneer

Pioneer AVIC-9DVD Bedienungsanleitung

Pioneer

Pioneer AVIC-F20BT Bedienungsanleitung

Pioneer

Pioneer AVIC-F77DAB Bedienungsanleitung

Pioneer

Pioneer AVIC-HD3 Bedienungsanleitung

Pioneer

Pioneer AVIC-Z1 Bedienungsanleitung

Pioneer

Pioneer CNSD-110FM Kurzanleitung

Beliebte Auto-Navigationssystem Handbücher anderer Marken

Clarion

Clarion Navigation In-Car Entertainment Bedienungsanleitung

Rosen

Rosen DP-1001 Bedienungsanleitung

Alpine

Alpine INE-W970HD Bedienungsanleitung

Skoda

Skoda AMUNDSEN+ Bedienungsanleitung

Blaupunkt

Blaupunkt TravelPilot DX-N Bedienungsanleitung

Sanyo

Sanyo NVM-4030 - Easy Street - Automotive GPS... Bedienungsanleitung

Kenwood

Kenwood DNN991HD Bedienungsanleitung

AvMap

AvMap Geosat 2C Bedienungsanleitung

Eonon

Eonon GE01B Bedienungsanleitung

Nextar

Nextar M3-MX - Automotive GPS Receiver Bedienungsanleitung

Furrion

Furrion NV2200 Bedienungsanleitung

Mio

Mio MOOV 200-Series Bedienungsanleitung

Prestigio

Prestigio GeoVision 5150 Bedienungsanleitung

Hummer

Hummer 2006 H3 Bedienungsanleitung

Magellan

Magellan Maestro 4210 - Automotive GPS Receiver Konfigurationshandbuch

Garmin

Garmin StreetPilot c510 Bedienungsanleitung

Garmin

Garmin nüvi 2200 Bedienungsanleitung

Garmin

Garmin 2610/2650 Bedienungsanleitung