Pioneer DEH-P85BT Bedienungsanleitung

MANUEL D’INSTALLATION

DEH-P85BT

INSTALLATION MANUAL

English Español Deutsch Français Italiano Nederlands PyÒÒÍËÈ

This product conforms to new cord colors.

Los colores de los cables de este producto se confor-

man con un nuevo código de colores.

Dieses Produkt entspricht den neuen Kabelfarben.

Le code de couleur des câbles utilisé pour ce produit est

nouveau.

Questo prodotto è conforme ai nuovi codici colori.

De kleuren van de snoeren van dit toestel zijn gewijzigd.

Ñ‡ÌÌÓÂ ÛÒÚÓÈÒÚ‚Ó ÒÓÓÚ‚ÂÚÒÚ‚ÛÂÚ ÌÓ‚˚Ï

ÚÂ·Ó‚‡ÌËﬂÏ Í ˆ‚ÂÚÛ ÔÓ‚Ó‰Ó‚.

Connecting the Units ................................ 1

Power cable connection .................................... 3

Connecting to separately sold power amp ........ 5

Installation .................................................. 7

DIN Front/Rear-mount ...................................... 7

DIN Front-mount .............................................. 7

DIN Rear-mount ................................................ 8

Fastening the front panel .................................. 9

Installing the microphone .................................. 9

Adjusting the microphone angle ......................10

Connecting the Units

Contents

Note:

• When this unit is installed in a vehicle without

ACC (accessory) position on the ignition switch,

red cable must be wired to the terminal that can

detect the operation of the ignition key.

Otherwise, battery drain may result.

• Use this unit in other than the following condi-

tions could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm

to 8 ohm (impedance value).

• To prevent short-circuit, overheating or malfunc-

tion, be sure to follow the directions below.

— Disconnect the negative terminal of the bat-

tery before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap adhe-

sive tape around them where they lie against

metal parts.

— Place all cables away from moving parts,

such as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a

battery.

— Cover any disconnected cable connectors

with insulating tape.

— Do not remove RCA caps if RCA cables are

not used.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power to other

equipment. Current capacity of the cable is

limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable direct-

ly to ground.

— Never band together multiple speaker’s nega-

tive cables.

No ACC positionACC position

English Español Deutsch Français Italiano Nederlands

• Control signal is output through blue/white cable

when this unit is powered on. Connect it to an

external power amp’s system remote control or

the vehicle’s auto-antenna relay control terminal

(max. 300 mA, 12 V DC). If the vehicle is

equipped with a glass antenna, connect it to the

antenna booster power supply terminal.

• Never connect blue/white cable to external power

amp’s power terminal. Also, never connect it to

the power terminal of the auto antenna.

Otherwise, battery drain or malfunction may

result.

• IP-BUS connectors are color-coded. Be sure to

connect connectors of the same color.

• Black cable is ground. This cable and other prod-

uct’s ground cable (especially, high-current prod-

ucts such as power amp) must be wired separate-

ly. Otherwise, fire or malfunction may result if

they are accidentally detached.

• Cord function may differ according to the

product, even if cord color is the same. When

connecting this system, be sure to check all

manuals and connect cords correctly.

FRANÇAIS

Connecting the Units

Connect leads of the same

color to each other.

Yellow (3*)

Back-up

(or accessory)

Red (5*)

Accessory

(or back-up)

Note:

Depending on the kind of vehicle, the function

of 3* and 5* may be different. In this case, be

sure to connect 2* to 5* and 4* to 3*.

Microphone Antenna jack

4 m 15 cm

Cap (1*)

Do not remove cap if this

terminal is not in use.

Yellow (2*)

Connect to the constant 12 V

supply terminal.

Orange/white

Connect to lighting switch terminal.

Red (4*)

Connect to terminal controlled by

ignition switch (12 V DC).

Black (chassis ground)

Connect to a clean, paint-free metal location.

Notes:

•Change the initial setting of this unit (refer to the Operation

Manual). The subwoofer output of this unit is monaural.

•When using a subwoofer of 70 W (2 Ω) , be sure to connect

with Violet and Violet/black leads of this unit. Do not connect

anything with Green and Green/black leads.

ISO connector

Note:

In some vehicles, the ISO connector

may be divided into two. In this

case, be sure to connect to both

connectors.

The pin position of the ISO connector will differ depends on the

type of vehicle. Connect 6* and 7* when Pin 5 is an antenna

control type. In another type of vehicle, never connect 6* and 7*.

iPod with Dock

Connector Dock connector port

Dock connector

2 m

Power cable connection

English Español Deutsch Français Italiano Nederlands

This product

Yellow/black

If you use an equipment with Mute function, wire

this lead to the Audio Mute lead on that equipment.

If not, keep the Audio Mute lead free of any

connections.

Speaker leads

White : Front left +

White/black : Front left ≠

Gray : Front right +

Gray/black : Front right ≠

Green : Rear left +or Subwoofer +

Green/black : Rear left ≠or Subwoofer ≠

Violet : Rear right +or Subwoofer +

Violet/black : Rear right ≠or Subwoofer ≠

Blue/white (6*)

IP-BUS cable

Multi-CD player

(sold separately)

IP-BUS input

(Blue)

Fuse (10 A)

Fuse resistor

Microphone input

14 cm

18 cm

Wired remote input

Hard-wired remote control adaptor can

be connected (sold separately).

Use a stereo mini plug cable

to connect with auxiliary

equipment.

AUX jack (3.5 ø)

Blue/white

Connect to system control terminal of the

power amp (max. 300 mA 12 V DC).

Blue/white (7*)

Connect to auto-antenna relay control

terminal (max. 300 mA 12 V DC).

Interface cable (e.g., CD-I200)

(sold separately)

Gray

Connecting the Units

This product

IP-BUS input

(Blue)

Antenna jack

14 cm

18 cm

15 cm

Refer to page 3 to 4.

Rear output

(REAR OUTPUT)

Subwoofer output

(SUBWOOFER OUTPUT)

Front output

(FRONT OUTPUT)

15 cm

30 cm

15 cm

Wired remote input

Hard-wired remote control adaptor can

be connected (sold separately).

AUX jack

(Refer to page 3 to 4.)

Notes:

•Change the initial setting of this unit

(refer to the Operation Manual). The

subwoofer output of this unit is monaural.

•When using a subwoofer of 70 W (2 Ω) ,

be sure to connect with Violet and

Violet/black leads of this unit. Do not

connect anything with Green and

Green/black leads.

ISO connector

Note:

In some vehicles, the ISO connector may

be divided into two. In this case, be sure

to connect to both connectors.

Speaker leads

White : Front left +

White/black : Front left ≠

Gray : Front right +

Gray/black : Front right ≠

Green : Rear left +or Subwoofer +

Green/black : Rear left ≠or Subwoofer ≠

Violet : Rear right +or Subwoofer +

Violet/black : Rear right ≠or Subwoofer ≠

Refer to page 3 to 4.

Microphone input

(Refer to page 3 to 4.)

IP-BUS cable

Multi-CD player

(sold separately)

Connecting to separately sold power amp

English Español Deutsch Français Italiano Nederlands

≠

Perform these connections when using the

optional amplifier.

Blue/white (6*)

System remote control

Rear speaker

Subwoofer Subwoofer

Rear speaker

Front speaker

Left Right

Power amp

(sold separately)

Power amp

(sold separately)

Power amp

(sold separately)

The pin position of the ISO connector will differ

depending on the type of vehicle. Connect 6* and

7* when Pin 5 is an antenna control type. In

another type of vehicle, never connect 6* and 7*.

Connect with RCA cables

(sold separately)

Blue/white (7*)

Connect to auto-antenna relay control

terminal (max. 300 mA 12 V DC).

Installation

Note:

•Check all connections and systems before final

installation.

•Do not use unauthorized parts. The use of

unauthorized parts may cause malfunctions.

•Consult with your dealer if installation requires

drilling of holes or other modifications of the

vehicle.

•Do not install this unit where:

—it may interfere with operation of the vehicle.

—it may cause injury to a passenger as a result

of a sudden stop.

•The semiconductor laser will be damaged if it

overheats. Install this unit away from hot places

such as near the heater outlet.

•Optimum performance is obtained when the unit

is installed at an angle of less than 60°.

•When installing, to ensure proper heat dispersal

when using this unit, make sure you leave ample

space behind the rear panel and wrap any loose

cables so they are not blocking the vents.

DIN Front/Rear-mount

This unit can be properly installed either from

“Front”(conventional DIN Front-mount) or

“Rear”(DIN Rear-mount installation, utilizing

threaded screw holes at the sides of unit chassis).

For details, refer to the following installation

methods.

DIN Front-mount

Installation with the rubber bush

1. Insert the mounting sleeve into the dashboard.

•When installing in a shallow space, use a sup-

plied mounting sleeve. If there is enough

space behind the unit, use factory supplied

mounting sleeve.

2. Secure the mounting sleeve by using a screwdriv-

er to bend the metal tabs (90°) into place.

3. Install the unit as illustrated.

182182

10 cm

60°

Rubber bush

Screw

Dashboard Mounting sleeve

Leave ample space Dashboard

Removing the Unit

1. Extend top and bottom of the trim ring outwards

to remove the trim ring. When reattaching the

trim ring, push the trim ring onto the unit until it

clicks. (If the trim ring is attached upside down,

the trim ring will not fit properly.)

•It becomes easy to remove the trim ring if the

front panel is released.

2. Insert the supplied extraction keys into both sides

of the unit until they click into place.

3. Pull the unit out of the dashboard.

DIN Rear-mount

1. Extend top and bottom of the trim ring outwards

to remove the trim ring. When reattaching the

trim ring, push the trim ring onto the unit until it

clicks. (If the trim ring is attached upside down,

the trim ring will not fit properly.)

•It becomes easy to remove the trim ring if the

front panel is released.

2. Determine the appropriate position where the

holes on the bracket and the side of the unit

match.

3. Tighten two screws on each side.

•Use either truss screws (5 mm ×8 mm) or

flush surface screws (5 mm ×9 mm), depend-

ing on the shape of screw holes in the

bracket.

Trim ring Trim ring

Screw

Dashboard or Console

Factory radio mounting bracket

English Español Deutsch Français Italiano Nederlands

Fastening the front panel

If you do not plan to detach the front panel, the

front panel can be fastened with supplied screw.

Installing the microphone

Installation notes

Install the microphone in a position and ori-

entation that will enable it to pick up the

voice of the person operating the system.

CAUTION

It is extremely dangerous to allow the

microphone lead to become wound

around the steering column or gearstick.

Be sure to install the unit in such a way

that it will not obstruct driving.

When installing the microphone on

the sun visor

1. Install the microphone on the micro-

phone clip.

Installation

Screw

Microphone

clip

Andere Handbücher für DEH-P85BT

Inhaltsverzeichnis

Sprachen:

Andere Pioneer Autoempfänger Handbücher

Pioneer

Pioneer KEH-P601 Bedienungsanleitung

Pioneer

Pioneer DEH-2950MP Bedienungsanleitung

Pioneer

Pioneer DEH-P4850MP Bedienungsanleitung

Pioneer

Pioneer CDX-P670X1N Bedienungsanleitung

Pioneer

Pioneer AVX-P7650TV Bedienungsanleitung

Pioneer

Pioneer AVD-W1100V Bedienungsanleitung

Pioneer

Pioneer RDS DEH-P40MP Bedienungsanleitung

Pioneer

Pioneer AppRadio SPH-DA100 Bedienungsanleitung

Pioneer

Pioneer AVH-P7650DVD Bedienungsanleitung

Pioneer

Pioneer AVH-P4350DVD Bedienungsanleitung

Pioneer

Pioneer KEH-3930R X1M/EW Bedienungsanleitung

Pioneer

Pioneer AVIC-Z720DAB Gebrauchs- und Pflegehandbuch

Pioneer

Pioneer Super Tuner IIID DEH-3250UB Bedienungsanleitung

Pioneer

Pioneer DEH-P9400BH Bedienungsanleitung

Pioneer

Pioneer DEH-P690UB - Premier Radio / CD Bedienungsanleitung

Pioneer

Pioneer FX-MG9106ZT/EW Bedienungsanleitung

Pioneer

Pioneer DEH-P65BT Bedienungsanleitung

Pioneer

Pioneer DEH-7300BT Bedienungsanleitung

Pioneer

Pioneer DEH-945UB Bedienungsanleitung

Pioneer

Pioneer AVH3850DVD Bedienungsanleitung

Pioneer

Pioneer RS-D7R Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Pioneer

Pioneer 2-DIN Bedienungsanleitung

Pioneer

Pioneer Super Tuner IIID DEH-P4200UB Bedienungsanleitung

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

JVC

JVC KD-AHD69 Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung

Medion

Medion Car Audio Bedienungsanleitung

Philips

Philips CEM5000 Bedienungsanleitung