Pioneer Pure Vision PDP-425CMX Installationshandbuch

PDP-425CMX

Plasma Display Panel

RS-232C Commands

COMMAND REFERENCE MANUAL

Manual Version 1.00

March 1, 2006

Pioneer Corporation

Pioneer Electronics (USA) Inc.

Industrial Solutions Business Group

RS-232C Adjustment

This display has an RS-232C terminal. It is possible to use a PC to make various adjustments and settings.

1.1 About the RS-232C Adjustment

Adjustments using the RS-232C:

• The adjustments are written to the same memory area as for the integrator mode (refer to section 5.4.4, “PICTURE,

White Balance and SCREEN Position Adjustment Values Memory Area Tables” pg. 187 in the Technical Manual).

(1) Assign an ID before using the RS-232C adjustment. Include the panel ID in the RS-232C command.

Refer to the next section “Interface” for details.

(2) Of the adjustment values and setting items set by RS-232C commands, there are some items that are

stored in memory and some that are not. For details, refer to section 5.5.5, “List of RS-232C Commands”

(pg. 197). Also, when storing values in “last” memory, the conditions described in section 5.1.5, “Last

Memory” (pg. 111 in the Technical Manual), must be satisfied.

(3) <OSDS00>/<OSDS01> (OSD display disable/enable setting)

Regardless of the setting, the following items can be displayed.

• Menu display (menu mode, integrator mode)

• Warnings before Auto Power OFF or Power Management operation

• Warning of high temperature inside the panel

• Display announcing that the FUNCTIONAL LOCK is set and the FUNCTIONAL LOCK setting display

• Display call (including holding a button down)

(4) When using RS-232C commands, control the input signal as well as the power. If the power is ON when

there is no signal, the display continues to have a weak discharge. This activity can affect the life of the

display.

Notes

PDP-425CMX

RS-232C Adjustment

1.2 Interface

1) Connector

D-sub 9 pins (male/straight)

2) Pin layout

3) Baud Rate

9600 bps (standard)

(switch-able to 1200, 2400, 4800, 19200, 38400 bps)

Note

The baud rate of this display should be set to match the baud rate of the PC.

Also, when the RS-232C cable is extended over a long distance, use a slower baud rate.

4) Data format

Start bit: 1 bit

Data bit: 8 bit

Parity: no

Stop bit: 1 bit

5) Connection

6) Protocol

From the PC to the display

Straight Cable

* D-sub 9-pin/D-sub 25-pin conversion tables are now available on the market.

Control PC Plasma Display Control PC Plasma Display

(with D25 serial port ) (PDP-425CMX/PDP-42MXE10) (with D9 serial port) (PDP-425CMX/PDP-42MXE10)

RXD 3 2 TXD RXD 2 2 TXD

TXD 2 3 RXD TXD 3 3 RXD

CTS 5 8 RTS CTS 8 8 RTS

GND 7 5 GND GND 5 5 GND

Pin No.

Signal

1 NC (not connected)

2 TxD (Transmit Data)

3 RxD (Receive Data)

4 NC (not connected)

5 GND

Pin No.

Signal

6 NC (not connected)

7 NC (not connected)

8 RTS (Request To Send)

9 NC (not connected)

(1) Sending one command at a time:

STX (02 hex) ID (2 Byte) COMMAND (3 Byte or 6 Byte) ETX (03 hex)

(2) Sending numerical direct commands:

STX (02 hex) ID (2 Byte) COMMAND (3 Byte) ARGUMENT (3 Byte) ETX (03 hex)

ID, COMMAND, ARGUMENT are transmitted as ASCII characters.

From the display to a PC

(1) Echo back (Normal response)

Command received and returned but the ID is not returned.

STX (02 hex) COMMAND (3 Byte or 6 Byte) ETX (03 hex)

Received command is a numerical direct effect command and numerical data is returned:

STX (02 hex) COMMAND (3 Byte) ARGUMENT (3 Byte) ETX (03 hex)

(2) Error (Abnormal response)

Received command is a non-corresponding command, ‘ERR’is returned:

STX (02 hex) ERR (3 Byte) ETX (03 hex)

Received command cannot be processed (when PON is received when the power is already ON, etc.), ‘XXX’is

returned:

STX (02 hex) XXX (3 Byte) ETX (03 hex)

RS-232C Adjustment

1.3 Combination Connection

When controlling/adjusting panels, it is convenient to connect several displays to one PC.

By performing a combination connection and assigning IDs to the panels, it is possible to control and adjust several

displays at the same time or separately.

Connection method:

Connect the panels as shown in the figure below.

Only the combination IN terminal or the RS-232C terminal can be used at the same time. Connecting them at the

same time could cause errors. Also, do not pair combination IN terminals or combination OUT terminals. Doing so

could cause communication to fail.

It is possible to use a general-purpose mini DIN 6-pin (straight) cable for the combination cable.

Note

To output RS-232C signals from the combination OUT terminal, an ID must be assigned.

Refer to the next section “ID Assignment”for details.

Note

IN OUT

RS-232C

IN OUT IN OUT

RS-232C

COMBINATION

RS-232C

COMBINATIONCOMBINATION

First Panel Second Panel Third Panel

Combination cable

OUT IN IN

OUT

RS-232C Adjustment

1.4 ID Assignment

The ID is assigned from the PC.

Commands: <IDC> (ID CLEAR) ........ Clears the assigned ID

<IDS> (ID SET) ............. Assigns an ID

IDS is only effective when an ID is not assigned.

IDs are assigned starting from the panel closest to the PC.

Example: Case of 4 displays (assigning IDs with the PC for the first time)

First, connect an RS-232C and combination cables. Refer to section “Combination cables” for details.

By sending RS-232C commands in this order, it is possible to assign an ID for each panel.

When a panel has a PC-assigned ID, it can only receive commands containing the ID. Assign an ID before sending a

command.

Characters that can be used for an ID include, 0 - 9 and A - F (there is not distinction between upper case and lower case

letters).

An ∗(asterisk) can be used as follows:

<∗∗IDC>: Clear the IDs assigned for all panels

<2∗IN1>: The input for which the first digit is 2 is set to INPUT1

Precautions when assigning IDs

Panels connected after a display’s ID has been cleared cannot be operated with RS-232C commands.

When the <∗∗IDC> command is sent, the IDs for all the sets from Set #1 to Set #4 are cleared. Only the first panel,

which is directly connected to the PC, can be controlled.

Send the command <01 IDS> to control the next panel. Continue setting IDs in this way for the remaining panels to

once again control the displays.

Note

When the IDs are set, when one or both of the IDs before a command is sent from the PC is an ∗, there is no echo.

When sending more commands, wait 6 seconds before sending the next command.

Example) When ∗∗OOO and ∗1OOO or 1∗OOO (OOO is the command) are sent from the PC, operation is performed

but there is no echo.

Set #4

ID = 04

Set #1 Set #2 Set #3

ID = 01

Sent commands:

1<01 IDS>

2<02 IDS>

3<03 IDS>

4<04 IDS>

ID = 02 ID = 03

OUT IN OUT IN OUT IN

‘

RS-232C connection

Under the connection conditions shown below, use a combination cable for up to 16 panels.

Conditions: 1Length of RS-232C cable connecting PC to PDP-425CMX/PDP-42MXE10: 5 m

2Combination cable length: 5 m each

3Wire specifications for linking cable: Mini Din 6-pin straight (7 strand cable)

For 1 strand, suitable for AWG28:

Cross-section area = 0.08 mm2

≠

7 strands ×πr2= 7 ×3.14 ×0.062= 0.079 mm2≠0.08 mm2

Note

For details on the number of displays that can be connected in series using the video OUT terminal (INPUT1, 4), refer to

section 2.3, “Controls and Connectors”(pg. 10) in the Technical Manual.

RS-232C

Combination cable 5m

PDP-425CMX

PDP-42MXE10

OUT

RS-232C Adjustment

1.5 List of RS-232C Commands

7Normal Operation Related Commands

Command Function Number direct Last

Effective Minimum Maximum memory

POWER

POF Turns the power OFF. 

PON Turns the power ON. 

INPUT SELECT

INPS01 Switches the main screen to INPUT1. 

INPS02 Switches the main screen to INPUT2. 

INPS03 Switches the main screen to INPUT3. 

INPS04 Switches the main screen to INPUT4. 

INPS05 Switches the main screen to INPUT5. 

IN1 Switches the main screen to INPUT1. 

IN2 Switches the main screen to INPUT2. 

IN3 Switches the main screen to INPUT3. 

IN4 Switches the main screen to INPUT4. 

IN5 Switches the main screen to INPUT5. 

SSIS01 Switches the sub screen to INPUT1. 

SSIS02 Switches the sub screen to INPUT2. 

SSIS03 Switches the sub screen to INPUT3. 

SSIS04 Switches the sub screen to INPUT4. 

SSIS05 Switches the sub screen to INPUT5. 

SWM Outputs main input to the full screen. 

SWS Outputs sub input to the full screen. 

SCREEN SIZE

AST Executes auto-setup. 

SZMS00 Sets SCREEN SIZE to DOT BY DOT. 

SZMS01 Sets SCREEN SIZE to 4 :3. 

SZMS02 Sets SCREEN SIZE to FULL. 

SZMS03 Sets SCREEN SIZE to ZOOM. 

SZMS05 Sets SCREEN SIZE to WIDE. 

SZMS06 Sets SCREEN SIZE to 14:9. 

SZMS09 Sets SCREEN SIZE to UNDERSCAN. 

SZMS10 Sets SCREEN SIZE to 2.35:1. 

VIDEO

PMTS00 Turns video mute to OFF.

PMTS01 Turns video mute to ON.

STLS00 Cancels FREEZE.

STLS01 Sets FREEZE.

AUDIO

VOL Adjusts audio volume. 000 042 

AMTS00 Turns audio mute to OFF.

AMTS01 Turns audio mute to ON.

AUSS01 Sets the audio source to main. 

AUSS02 Sets the audio source to sub. 

MULTI SCREEN

MSCS00 Turns MULTI SCREEN to OFF. 

MSSS01 Sets the PinP subscreen size to 1. 

MSSS02 Sets the PinP subscreen size to 2. 

MSSS03 Sets the PinP subscreen size to 3. 

MSSS04 Sets the PinP subscreen size to 4. 

MSTS01 Sets the MULTI SCREEN to 2 SCREEN (side by side 1) 

MSTS02 Sets the MULTI SCREEN to PinP (lower right). 

MSTS03 Sets the MULTI SCREEN to PinP (upper right). 

MSTS04 Sets the MULTI SCREEN to PinP (upper left). 

MSTS05 Sets the MULTI SCREEN to PinP (lower left). 

MSTS06 Sets the MULTI SCREEN to PoutP (side by side, 2-L). 

RS-232C Adjustment

7“MENU”–“SET UP”related commands

Command Function Number direct Last

Effective Minimum Maximum memory

COLOR TEMP.

CTPS01 Sets the color temperature to LOW. 

CTPS02 Sets the color temperature to MID LOW. 

CTPS03 Sets the color temperature to MIDDLE. 

CTPS04 Sets the color temperature to MID HIGH. 

CTPS05 Sets the color temperature to HIGH. 

DNR

DNRS00 Sets digital NR to OFF. 

DNRS01 Sets digital NR to LOW. 

DNRS02 Sets digital NR to MIDDLE. 

DNRS03 Sets digital NR to HIGH. 

MPEG NR

MNRS00 Sets MPEG NR to OFF. 

MNRS01 Sets MPEG NR to LOW. 

MNRS02 Sets MPEG NR to MIDDLE. 

MNRS03 Sets MPEG NR to HIGH. 

CTI

CTRS00 Sets CTI to OFF. 

CTRS01 Sets CTI to ON. 

PURE CINEMA

PUCS00 Sets PURE CINEMA to OFF. 

PUCS01 Sets PURE CINEMA to STANDARD. 

COLOR DECORDING

MCDS01 Sets COLOR DECORDING to RGB (VIDEO). 

MCDS02 Sets COLOR DECORDING to COMPONENT1 (YCbCr). 

MCDS03 Sets COLOR DECORDING to COMPONENT2 (YPbPr). 

COLOR SYSTEM

CLSS01 Sets color system to AUTO. 

CLSS02 Sets color system to NTSC. 

CLSS03 Sets color system to PAL. 

CLSS04 Sets color system to SECAM. 

CLSS05 Sets color system to 4.43NTSC. 

CLSS06 Sets color system to PAL M. 

CLSS07 Sets color system to PAL N. 

SIGNAL FORMAT

SFTS01 Sets SIGNAL FORMAT to Type1. 

SFTS02 Sets SIGNAL FORMAT to Type2. 

SFTS03 Sets SIGNAL FORMAT to Type3. 

SFTS04 Sets SIGNAL FORMAT to Type4. 

Command Function Number direct Last

Effective Minimum Maximum memory

MSTS08 Sets MULTI SCREEN to SWAP (switches between main and sub screens). 

MSTS09 Sets MULTI SCREEN to PoutP (side by side 2-R). 

MSTS10 Sets MULTI SCREEN to 2-SCREEN (side by side 3). 

MSTS11 Sets MULTI SCREEN to PoutP (side by side 4-L). 

MSTS12 Sets MULTI SCREEN to PoutP (side by side 4-R). 

FUNCTIONAL LOCK

FCLS00 Cancels FUNCTIONAL LOCK. 

FCLS01 Prohibits operation of buttons on the display. 

FCLS02 Prohibits operation of buttons on the remote control. 

FCLS03 Prohibits operation of buttons on the display/remote control. 

FCLS04 Sets the memory lock. 

OSD

DOF Turns off the OSD display that is now displayed.

RS-232C Adjustment

7“MENU”–“OPTION”related commands

Command Function Number direct Last

Effective Minimum Maximum memory

ENERGY SAVE

ESVS00 Sets ENERGY SAVE to standard. 

ESVS01 Sets ENERGY SAVE to save energy. 

ESVS02 Sets ENERGY SAVE to fixed brightness. 

ESVS03 Sets ENERGY SAVE to mode 3 (long service life). 

ESVS04 Sets ENERGY SAVE to AUTO. 

TIMER

TSMS00 Turns summer time to OFF. 

TSMS01 Turns summer time to ON. 

TPH Sets the hour of the present time. 000 023 

TPM Sets the minute of the present time. 000 059 

TPW Sets the day of week of the present time. 001 007 

TPTS00 Sets PROGRAM TIMER to OFF. 

TPTS01 Sets PROGRAM TIMER to ON. 

ORBITER

ORBS00 Sets the ORBITER to OFF. 

ORBS01 Sets the ORBITER to ON (AUTO1). 

ORBS02 Sets the ORBITER to ON (AUTO2). 

ORBS03 Sets the ORBITER to ON (AUTO3). 

SOFT FOCUS

SOFS00 Sets SOFT FOCUS to OFF. 

SOFS01 Sets SOFT FOCUS to 1. 

SOFS02 Sets SOFT FOCUS to 2. 

SOFS03 Sets SOFT FOCUS to 3. 

SOFS04 Sets SOFT FOCUS to 4. 

SUB SCREEN FREEZE

SSTS00 Sets SUB SCREEN FREEZE to OFF. 

SSTS01 Sets SUB SCREEN FREEZE to SIDE BY SIDE. 

SSTS02 Sets SUB SCREEN FREEZE to PinP. 

Command Function Number direct Last

Effective Minimum Maximum memory

SFTS05 Sets SIGNAL FORMAT to Type5. 

SFTS06 Sets SIGNAL FORMAT to Type6. 

SFTS07 Sets SIGNAL FORMAT to Type7. 

SFTS08 Sets SIGNAL FORMAT to Type8. 

SFTS10 Sets SIGNAL FORMAT to AUTO. 

DVI

DSGS01 Sets the DVI connection signal to PC. 

DSGS02 Sets the DVI connection signal to STB/DVD. 

DBLS01 Sets the DVI BLACK LEVEL to LOW. 

DBLS02 Sets the DVI BLACK LEVEL to HIGH. 

7“INTEGRATOR”–“PICTURE”related commands

Command Function Number direct Last

Effective Minimum Maximum memory

VIDEO QUALITY

CNT Adjusts the contrast. 000 255 

BRT Adjusts the brightness. 000 255 

ENH Adjusts the horizontal enhance. 000 015 

ENV Adjusts the vertical enhance. 000 015 

COL Adjusts the color. 000 127 

TNT Adjusts the tint. 000 060 

SHP Adjusts the sharpness. 000 015 

RS-232C Adjustment

Command Function Number direct Last

Effective Minimum Maximum memory

WHITE BALANCE

RHI Adjusts R.HIGH of the white balance. 000 255 

GHI Adjusts G.HIGH of the white balance. 000 255 

BHI Adjusts B.HIGH of the white balance. 000 255 

GLW Adjusts G.LOW of the white balance. 000 255 

RLW Adjusts R.LOW of the white balance. 000 255 

BLW Adjusts B.LOW of the white balance. 000 255 

COLOR DETAIL

CGR Adjusts color detail red. 000 060 

CGY Adjusts color detail yellow. 000 060 

CGG Adjusts color detail green. 000 060 

CGC Adjusts color detail cyan. 000 060 

CGB Adjusts color detail blue. 000 060 

CGM Adjusts color detail magenta. 000 060 

GAMMA

GRAS18 Sets gradation GAMMA 1.8. 

GRAS19 Sets gradation GAMMA 1.9. 

GRAS20 Sets gradation GAMMA 2.0. 

GRAS21 Sets gradation GAMMA 2.1. 

GRAS22 Sets gradation GAMMA 2.2. 

GRAS23 Sets gradation GAMMA 2.3. 

GRAS24 Sets gradation GAMMA 2.4. 

PRESET

STD Restores the PICTURE, W/B adjustment value of the integrator to the initial values. 

7“INTEGRATOR”–“SCREEN”related commands

Command Function Number direct Last

Effective Minimum Maximum memory

POSITION

HPS Adjusts the horizontal position. 000 255 

VPS Adjusts the vertical position. 000 255 

CLOCK/PHASE

CFR Adjusts the CLOCK (PLL frequency). 000 255 

CPH Adjusts the PHASE (PLL phase). 000 031 

SIZE

HSI Adjusts the horizontal size. 000 064 

VSI Adjusts the vertical size. 000 064 

PRESET

FRP Restores the SCREEN adjustment value of the integrator to the initial values. 

7“NTEGRATOR”–“SET UP”related commands

Command Function Number direct Last

Effective Minimum Maximum memory

SUB VOLUME

SVL Adjusts the SUB VOLUME. 000 020 

Andere Handbücher für Pure Vision PDP-425CMX

Inhaltsverzeichnis

Andere Pioneer Monitor Handbücher

Pioneer

Pioneer Elite PRO-1120HD Bedienungsanleitung

Pioneer

Pioneer PDP 433CMX Bedienungsanleitung

Pioneer

Pioneer PDK-5008FT Bedienungsanleitung

Pioneer

Pioneer PDP-505PE Bedienungsanleitung

Pioneer

Pioneer Elite PureVision PRO 940HD Bedienungsanleitung

Pioneer

Pioneer Elite PRO-1010HD Bedienungsanleitung

Pioneer

Pioneer PDP-42MXE10 Benutzerhandbuch

Pioneer

Pioneer PDP-5016 Bedienungsanleitung

Pioneer

Pioneer PDU-50WX2 Bedienungsanleitung

Pioneer

Pioneer PDP-505HD Bedienungsanleitung

Pioneer

Pioneer pdp-506hdg Bedienungsanleitung

Pioneer

Pioneer PDP-614MX Bedienungsanleitung

Pioneer

Pioneer AVD-W9000 Bedienungsanleitung

Pioneer

Pioneer PDP-4270HD Bedienungsanleitung

Pioneer

Pioneer PDP-436RXE Bedienungsanleitung

Pioneer

Pioneer Pure Vision PDP-425CMX Bedienungsanleitung

Pioneer

Pioneer PDP5030HD - PDP - 503OHD Einrichtungshandbuch

Pioneer

Pioneer PDP-5040HD Montageanleitung

Pioneer

Pioneer PDP 507CMX Bedienungsanleitung

Pioneer

Pioneer Elite PRO-FHD1 Bedienungsanleitung

Pioneer

Pioneer PDP 424MV Bedienungsanleitung

Pioneer

Pioneer PureVision PDP-427XG Bedienungsanleitung

Pioneer

Pioneer PDP-4360HD Bedienungsanleitung

Pioneer

Pioneer PDP-505PG Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung