Pioneer SX-950 Referenzhandbuch

SX-950 ALIGNMENT PROCEDURES

9.1 AM SECTION

1. Set function switch to AM.

2. Connect AM signal generator through 1k-ohm

resistor to AM antenna terminal.

3. Set DUPLICATE switch to OFF and connect

an AC voltmeter to TAPE 1 REC jacks.

4. Set AM SG for 400Hz 30% modulation 100dB

output.

5. Set SX-950 dial indication and AM SG

frequency for 600kHz.

6. Adjust T8 core for maximum reading on AC

voltmeter.

7. Set SX-950 dial indication and AM SG

frequency for 1,400kHz.

8. Adjust TC5 for maximum reading on AC

voltmeter.

9. Set AM SG for 30dB output.

10. Set SX-950 dial indication and AM SG

frequency for 600kHz.

11. Adjust T7, T8 and bar antenna core for

maximum reading on AC voltmeter.

12. Set SX-950 dial indication and AM SG

frequency for 1,400kHz.

13. Adjust TC5, TC6 and TC7 for maximum

reading on AC voltmeter.

14. Repeat steps 10-13 to eliminate variations in

AC voltmeter readings.

9.2 FM TUNER

1. Set function switch to FM.

2. Set FM MUTING switch to OFF.

3. Connect FM signal generator through 300-ohm

dummy load to 300 ohm FM antenna terminals.

4. Set DUPLICATE switch to OFF and connect

AC voltmeter to TAPE 1 REC jacks.

5. Set FM SG for 100dB output at 400Hz and

100% modulation.

6. Set SX-950 dial indication and FM SG

frequency for 87.4MHz.

7. Adjust T4 core for maximum indication on

SIGNAL meter.

8. Adjust T6 lower core for center of scale

indication on TUNING meter.

9. Set FM SG for 8dB output and adjust cores of

T1, T2, and T3 for maximum reading on AC

voltmeter.

10. Set FM SG for 100dB output.

11. Set SX-950 dial indication and FM SG

frequency for 106MHz.

12. Adjust TC4 for maximum indication on

SIGNAL meter.

13. Set FM SG for 8dB output and adjust TC1,

TC2 and TC3 for maximum reading on AC

voltmeter.

14. Set FM SG for 100dB output.

15. Set SX-950 dial indication and FM SG

frequency for 87.4MHz.

16. Adjust T4 core for maximum indication on

SIGNAL meter.

17. Set FM SG for 8dB output and adjust cores of

T1, T2 and T3 for maximum reading on AC

voltmeter.

18. Repeat steps 10-17 to eliminate variations in

AC voltmeter readings.

19. After completing above adjustments, adjust T5

core for maximum reading on AC voltmeter.

20. Detune SX-950 to where only noise is

received and adjust T6 lower core for center of

scale indication on TUNING meter.

21. Set FM SG for 98MHz 60dB output.

22. Tune SX-950 for exact center of scale

indication on TUNING meter.

23. Adjust T6 upper core for minimum distortion.

24. Repeat steps 20- 23 to eliminate variations in

point of minimum distortion.

25. Set FM SG for 100dB output and adjust VR3

so that SIGNAL meter indicates 5 of the scale.

Multiplex Decoder

26. Connect MPX SG (multiplex signal generator)

to the external modulator terminals of the FM

SG and set the FM SG for external

modulation.

27. Connect PILOT OUT terminal of MPX SG to

horizontal input terminal of oscilloscope.

28. Through probe, connect oscilloscope vertical

input terminal to terminal No. 19.

29. Set FM SG for 98MHz 60dB output

unmodulated.

30. Tune SX-950 for exact center of scale

indication on TUNING meter.

31. Adjust VR1 so that 4:1 frequency ratio

Lissajous' (see note below) figure becomes

stationary.

32. Set FM SG for 1kHz (L or R), ?67.5kHz

deviation, 19kHz (pilot signal) and +7.5kHz

modulation.

33. Adjust VR2 for minimum L-R crosstalk.

Note:

Signal at terminal No. 19 is 76kHz sawtooth wave

and MPX SG pilot out is a 19kHz sine wave.

These form a Lissajous figure as shown in Fig.

23.

FM Alignment

If FM stations have drifted in their indicated positions on the dial you might be able to get the FM

Local Oscillator back to where it belongs with a bit of luck and careful adjustment.

Set the SX-950 tuning pointer to about 98 MHz, at the indicated frequency of a known station very

close to 98. Then get another FM receiver tuned to this station to hear the audio content. Verify that

the movable fins of the SX-950 tuning variable capacitor are at their approximate midpoint as well.

This is critical.

Attempt to adjust TC4to locate and tune the known station. Basically you are going to walk the tuning

to the correct indicated position. This adjustment will be extremely sensitive. Ideally a plastic tool

with a metal blade would be used to trim this adjustment (such as a trimpot tool) but a micro

screwdriver may suffice. Be aware the metal screwdriver shaft can affect the capacitance or

inductance of the device being adjusted. Anticipate this factor to get it close once the tool is moved

away from the device.

IF YOU GET LOST, stop at a station, then use the other FM receiver to match the audio and read the

frequency.

Alternately, you can also begin with the tuner set to 98MHz, tune TC4to the first audio you can find,

then find the station frequency with the other receiver. Adjust the SX-950 to the next station's audio,

determine where you are at and keep on repeating until the station is located.

9.3 POWER AMPLIFIER SECTION

1. Turn VR3 and VR4 fully counter-clockwise before

turning on the power.

2. Remove jumper plugs connecting POWER IN and PRE

OUT jacks.

3. Connect 5.1 K-ohm resistor to POWER IN jacks.

4. Set power amplifier for no load.

5. Set POWER switch to ON.

6. Adjust VR1 for 0V between terminals No. 10 and No. 9.

7. Adjust VR2 for 0V between terminals No. 25 and No.

24.

8. Adjust VR3 for 20mV between terminals No. 12(+) and

No. 13(-).

9. Adjust VR4 for 20mV between terminals No. 27(+) and

No. 28(-).

10. Allow set to warm up for at least 10 minutes, then

readjust.

Andere Handbücher für SX-950

Andere Pioneer Stereo-Receiver Handbücher

Pioneer

Pioneer VSX-D704S Bedienungsanleitung

Pioneer

Pioneer MVH-A219BT Bedienungsanleitung

Pioneer

Pioneer SX-3500 Bedienungsanleitung

Pioneer

Pioneer SX303R Bedienungsanleitung

Pioneer

Pioneer DMH-WT38NEX Bedienungsanleitung

Pioneer

Pioneer VSX-1015TX Bedienungsanleitung

Pioneer

Pioneer vsx-9900s Bedienungsanleitung

Pioneer

Pioneer AVH-P7950DVD/RC Bedienungsanleitung

Pioneer

Pioneer SX-580 Bedienungsanleitung

Pioneer

Pioneer VSX-D514 Bedienungsanleitung

Pioneer

Pioneer VSX-3300 Bedienungsanleitung

Pioneer

Pioneer XR-P560F Bauanleitung

Pioneer

Pioneer SX-1500T Bedienungsanleitung

Pioneer

Pioneer VSX-532 Bedienungsanleitung

Pioneer

Pioneer sx-550 Bedienungsanleitung

Pioneer

Pioneer SX-2700 Bedienungsanleitung

Pioneer

Pioneer SX-525 FVZW Bedienungsanleitung

Pioneer

Pioneer SX-2900 Bedienungsanleitung

Pioneer

Pioneer VSX-824-K Bedienungsanleitung

Pioneer

Pioneer DMH-G220BT Bedienungsanleitung

Pioneer

Pioneer XR-P370C Bedienungsanleitung

Pioneer

Pioneer VSX-454 Bedienungsanleitung

Pioneer

Pioneer SPH-EVO82DAB Bedienungsanleitung

Pioneer

Pioneer ELITE VSX-LX305 Handbuch

Beliebte Stereo-Receiver Handbücher anderer Marken

Marantz

Marantz CINEMA 70S Bedienungsanleitung

Kenwood

Kenwood KMDX92 Bedienungsanleitung

Yamaha

Yamaha RX-830 Bedienungsanleitung

Yamaha

Yamaha RX-750 Bedienungsanleitung

Denon

Denon AVR-1311 Bedienungsanleitung

Denon

Denon AVR-S760H Bedienungsanleitung

Denon

Denon AVR-X7200W Bedienungsanleitung

Sony

Sony XAV-1500 Bedienungsanleitung

Radio Shack

Radio Shack DX-399 Bedienungsanleitung

Sony

Sony STR-DE535 - Fm Stereo/fm-am Receiver Bedienungsanleitung

Yamaha

Yamaha MusicCast TSR-5B3D Bedienungsanleitung

Sony

Sony STR-DE335 - Fm Stereo/fm-am Receiver Bedienungsanleitung

Sony

Sony STR-DG500 - Multi Channel Av Receiver Bedienungsanleitung

Panasonic

Panasonic AJSD955B - DVCPRO50 STUDIO DECK Bedienungsanleitung

Sherwood

Sherwood S-2660CP Technisches Handbuch

Sony

Sony STR-K790 - Lifier Bedienungsanleitung

Denon

Denon DRA-697CI Bedienungsanleitung

SMART-AVI

SMART-AVI HDX-PRO Series Bedienungsanleitung