Pizzi instruments Water Level Meter Bedienungsanleitung

Pizzi Instruments S.r.l.

Via del Fornaccio, 46 –50012 Bagno a Ripoli (FI) Italy

Tel.0039 0556810722 –Fax 0039 (0)55 6584923 –

email: info@pizzi-instruments.it - web: www.pizzi-instruments.it 1

Water Level Meter

Instruction Manual

Pizzi Instruments S.r.l.

Via del Fornaccio, 46 –50012 Bagno a Ripoli (FI) Italy

Tel.0039 0556810722 –Fax 0039 (0)55 6584923 –

email: info@pizzi-instruments.it - web: www.pizzi-instruments.it 2

Pizzi Instruments S.r.l. reserves the right to change the information contained in this document without

notice.

No part of this document may be reproduced without the prior written consent of Pizzi Instruments S.r.l.

The instruments supplied by Pizzi Instruments S.r.l. are designed and optimized to be used and installed

with simplicity.

However, since they are performed at a high technical level, they must be installed and used by a trained

and qualified technical staff.

Before the installation of the supplied instrumentation, it is advisable to carefully read this manual and any

other related documents.

Pizzi Instruments S.r.l.

Warranty

Pizzi Instruments S.r.l. warrants its product against defects in materials for twelve (12) months from the date

of shipment unless otherwise specified on the relevant contract or purchase order.

Products considered to be defective should be returned to Pizzi Instruments factory properly identified,

complete with serial number, Returned Materials Authorization (RMA) and freight prepaid.

Pizzi Instruments’ obligation under this warranty is limited to repairing or replacing (at Pizzi Instruments’

discretion) defective products, which shall be the sole and exclusive solution under this warranty.

The Customer shall assume all costs of removing and shipping defective products to Pizzi Instruments and

the costs of reinstalling the repaired/substituted instruments.

The foregoing warranty shall not apply to any Pizzi Instruments products which have been subjected to

modification, misuse, misapplication, neglect, improper service or maintenance, improper installation.

Pizzi Instruments S.r.l. is not liable for any damage or loss caused to other equipment or person, whether

direct, indirect, incidental, special or consequential which the buyer may experience as a result of the

installation or use of the product.

The amount of any claim is limited to the net invoice value of the item in question.

In no case Pizzi Instruments S.r.l. will recognize and reimburse the costs incurred by the customer for

installations, maintenance, management, as well as for the uninstallation and reinstallation of the instruments

to be repaired or replaced under warranty.

While the information contained in the manual is assumed to be accurate, Pizzi Instruments neither assumes

responsibility for any omission or error that may appear or assumes liability for any damage or loss that

result from the use of products in accordance with the information contained in the manual.

Pizzi Instruments S.r.l.

Document Revision

Date

Revision

Issued

Checked

Authorized

10/01/2013

001

ANP

MPZ

FPZ

08/04/2018

002

ANP

MPZ

FPZ

Pizzi Instruments S.r.l.

Via del Fornaccio, 46 –50012 Bagno a Ripoli (FI) Italy

Tel.0039 0556810722 –Fax 0039 (0)55 6584923 –

email: info@pizzi-instruments.it - web: www.pizzi-instruments.it 3

Table of contents

Symbols and abbreviations ............................................................................................................................... 5

1. Introduction.................................................................................................................................................... 5

2. Initial Inspection............................................................................................................................................. 5

2.1 Damage during shipment ............................................................................................................................ 6

3. Storage .......................................................................................................................................................... 6

4. Description..................................................................................................................................................... 6

4.1 Instrument Components........................................................................................................................... 6

5. Preliminary requirements............................................................................................................................... 7

6.1 Preliminary Operations ............................................................................................................................ 7

7. Taking Measure............................................................................................................................................. 7

8. Technical Assistance..................................................................................................................................... 7

Pizzi Instruments S.r.l.

Via del Fornaccio, 46 –50012 Bagno a Ripoli (FI) Italy

Tel.0039 0556810722 –Fax 0039 (0)55 6584923 –

email: info@pizzi-instruments.it - web: www.pizzi-instruments.it 4

Use of this manual

This manual must be considered for the installation and use of Water Level Meter .

Dangers and safety

Warning for the unpacking of the material:

Be careful when handling the packaging to avoid damage to property and / or people.

Handle with care every package before you open it.

Be sure to open every package without risking damage its contents.

Separate carefully each component of the package.

Warning for the installer:

Be careful in handling the heavy metal parts

Be careful when handling bulky packaging

Caution: Handle with care the bars of stainless steel and the bottom elements

Caution: Always use appropriate Personal Protective Equipment (PPE)

Be careful not to apply any shock to the instrument

Warnings for the disposal of the material

All material must be disposed in accordance with local regulations of the country where the

equipment will be installed and where it will be removed.

Pizzi Instruments S.r.l.

Via del Fornaccio, 46 –50012 Bagno a Ripoli (FI) Italy

Tel.0039 0556810722 –Fax 0039 (0)55 6584923 –

email: info@pizzi-instruments.it - web: www.pizzi-instruments.it 5

Symbols and abbreviations

Highlights important information

The Caution Symbol highlights the presence of a potential danger.

CAUTION: of instrument damage. All conditions specified in the associated text must be

fully known and understood before proceeding

This symbol indicates that the product at the end of its useful life must be collected

separately from other waste. The operator must therefore send the equipment to the

appropriate centers for collection of electronic and electrotechnical waste

1. Introduction

This instrument is used for the measurement of water levels in wells or in piezometric pipes.

The instrument is easy to use and has a rugged and robust design.

The principle of measurement is simple; an electric cable with two conductors is lowered into a well or

borehole until it enters into contact with the water surface to be measured.

On the head is the probe which acts as a weighting body for the cable and the element that touches the

water.

Once contact has occurred, the water short circuits the two final pins of the probe.

This short circuit is detected by an acoustic device with suitable battery located at the other end of the cable,

housed in the cable reel.

The connection cable is inextensible and graduated in centimeters (or in millimeters for the model with flat

cable tape).

When the probe head enters into contact with the water, an acoustic signal warns the operator and at that

moment, it is possible to detect by direct reading of the cable, the depth at which contact occurred,

determining the depth of the water surface and thus its level.

2. Initial Inspection

All the instruments have been carefully inspected, both mechanically and electrically, before they leave the

factory.

Please check if all received items correspond with the packing list, your order confirmation and if the list of

components (chapter 4.1) corresponds to the material effectively present.

In case of discrepancy, please contact Pizzi Instruments or your local Representative.

NOTE: All instruments are thoroughly checked both electrically and mechanically before leaving the

factory.

Pizzi Instruments S.r.l.

Via del Fornaccio, 46 –50012 Bagno a Ripoli (FI) Italy

Tel.0039 0556810722 –Fax 0039 (0)55 6584923 –

email: info@pizzi-instruments.it - web: www.pizzi-instruments.it 6

2.1 Damage during shipment

If requested at the moment of the order, all instruments can be insured prior to shipment. If you receive a

damaged shipment and shipping insurance was previously arranged you should:

Report the damage to your shipper immediately

Inform Pizzi Instruments or your local representative immediately

Keep all packaging and shipping documents

NOTE: All shipments must immediately opened upon delivery and the content must be

checked, in quality and quantity, on the base of the packing list sent together with the goods.

No claims for shortages, damages or errors will be considered valid if no writing form to our

office within 3 days of receipt of goods will be sent.

Attention: insurance claims may be void if the above procedure is not followed.

3. Storage

Keep the material in a proper site to avoid its deterioration before the installation and to protect it

from any possibility of shocks.

Do not place weights on top of the instrumentation

Do not store the equipment in places where it could cause damage to persons or property

Be careful during the storage not to bend or crush the steel parts

4. Description

4.1 Instrument Components

The system includes :

A probe provided with two contacts in conductive material insulated by a special drip edge.

An additional head for the weighting of the probe.

An inextensible cable with flat or round shape (flat with millimeter or centimeter graduation,

according to model).

The model with flat cable has a maximum external diameter of 12 mm and can be used together with all

piezometric pipes normally in use.

Smaller diameter head(10mm) can only be supplied with the circular cable model.

Pizzi Instruments S.r.l.

Via del Fornaccio, 46 –50012 Bagno a Ripoli (FI) Italy

Tel.0039 0556810722 –Fax 0039 (0)55 6584923 –

email: info@pizzi-instruments.it - web: www.pizzi-instruments.it 7

5. Preliminary requirements

Before using the instrument, it is a good rule to check the suitable conditions in the area where the

instrument is used.

A very important procedure for the correct use and the following operation of the instrument is the elimination

of any deposits of any material both on the probe head and on the cable.

6.1 Preliminary Operations

Check the correct operation of the instrument by setting the switch on "ON" position and immerse the head in

a container with water, if everything properly works you will hear the "beep" and the "LED" will light up; failure

to operate may depend either on damage to the cable or on the exhaustion of the battery ("9V") housed on

the front panel.

7. Taking Measure

1. Lower the head into the hole where the measurement is to be made, on contact with the water the

instrument will emit a "beep" and the "LED" will light up.

2. Raise the probe until the sound stops and then re-trace it again to find the contact point for subsequent

approximations

3. Read the measurement directly on the cable and write it down on a previously prepared table

4. At the end of the measurements, clean the instrument and check it again.

8. Technical Assistance

Pizzi Instruments S.r.l. has a wide range of service as phone assistance, installation, training, calibration,

reparation and maintenance.

For any additional information you can directly contact our technicians at the following addresses:

tec@pizzi-instruments.it

T: +39055 6810722

F: +39055 6584923

Inhaltsverzeichnis

Andere pizzi instruments Messgerät Handbücher

pizzi instruments

pizzi instruments PNT-G2 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung

pizzi instruments Water Level Meter Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken