Planet GRT-101 Bedienungsanleitung

G.SHDSL Bridge Router

GRT-101/GRT-401/GRT-402

Quick Installation Guide

Table of Contents

Chapter 1 Before Starting Up............................................................................ 3

Chapter 2 Quick Installation ............................................................................. 4

2.1 Bridge Mode ............................................................................. 4

2.2 Routing Mode for PPPoA and PPPoE with IP Sharing ..................... 6

2.3 Routing Mode for IPoA or EoA .................................................... 9

2.4 LAN-to-LAN Connection with Bridge Mode...................................13

Chapter 1 Before Starting Up

Before proceeding any further, please make sure correct Ethernet cable is used

for connecting the LAN port of your computer to GRT-101/401/402. The LAN LNK

indicator on the front panel will light up if a correct cable is used.

By default, the GRT-101/401/402 is shipped with its DHCP Server function enabled.

This means the client computers on the LAN network including the Administrator

PC can set their TCP/IP settings to automatically obtain an IP address from the

GRT-101/401/402.

■Start your web browser and type http://192.168.0.1 in the browser’s address

box, and wait for the login screen appears. The default user name and pass-

word are “root”. Click OK button and you will login the management of

GRT-101/401/402.

Note

The factory default management IP and subnet mask of GRT-

101/401/402 is 192.168.0.1 and 255.255.255.0 respectively. And

the default user name and password are “root”.

This quick installation guide is intended to help to install the G.SHDSL Bridge

Router to the network through the management interface. For more detailed

settings, please also refer to the user’s manual.

Chapter 2 Quick Installation

This chapter provides quick setup procedures for four major connection modes:

Section 2.1: Bridge Mode

Section 2.2: Routing Mode for PPPoA and PPPoE

Section 2.3: Routing Mode for IPoA or EoA

Section 2.4: LAN to LAN Bridge Mode

Please verify your connection mode and check the corresponding section to quickly

install your GRT-101/401/402.

2.1 Bridge Mode

GRT-101

LAN IP 192.168.0.1

Mask 255.255.255.0

IP 192.168.0.31

Mask 255.255.255.0

Gateway 192.168.0.254

VPI = 0, VCI = 32

Encapsulation = LLC

BAS

IP 192.168.0.254

DSLAM

Bridge Mode

ISP

Web UI Conguration

After connection via web browser, click and to set up Bridging

mode of GRT-101/401/402 and then click for the next setting.

1. Enter WAN1 VPI: 0and VCI: 32.

2. Select WAN1 AAL5 Encap:

3. Enter LAN IP: 192.168.0.1

4. Enter LAN Sub-net Mask: 255.255.255.0

5. Enter Gateway: 192.168.0.254

The Gateway is directly pointed to the BAS IP.

6. Enter DNS Server : 168.95.1.1 and 168.95.192.1

7. Click

8.The screen will prompt the new congured parameters. Check the parameters

and click

. The router will reboot with the new setting or click

tocongureotherparameters.

Console Conguration

Do the following steps:

1. User: admin password: admin 

2. enable supervisor password: root 

3. setup mode Bridge 

4. wan Interface number (1~8): 1 

Protocol : Ethernet 

vpi_vci: 0 

32 

encap: LLC 

5. bridge gateway 192.168.0.254 

6. lan Interface number: 1 

7 address 192.168.0.1 

255.255.255.0 

8. (back to root) write y 

y (reboot)

2.2 Routing Mode for PPPoA and PPPoE with IP Sharing

GRT-101

LAN IP 192.168.0.1

Mask 255.255.255.0

IP 192.168.0.2

Mask 255.255.255.0

Gateway 192.168.0.1

DNS 192.168.0.1

VPI = 0, VCI = 32

Encapsulation = LLC

BAS

DSLAM

Router Mode

usrname: user1@net

password: user

ISP

WANLAN

Web UI Conguration

For Route Mode with Point-to-Point Protocol over ATM and Ethernet, follow the

following settings. First select and

, and then click for

setting other parameters.

1. Enter LAN IP: 192.168.0.1

2. Enter LAN Sub-net Mask: 255.255.255.0

3. Host Name: SOHO

4. DHCP Server: Enable

5. Click

6. Enter DHCP Client Start IP: 192.168.0.2

7. Enter DHCP Client End IP: 192.168.0.51

8. Enter DNS Server: 192.168.0.1

9. The DNS server is embedded in GRT-101/401/402.

10.Click to write the new setting.

11.Enter WAN1 VPI: 0and VCI: 32.

12.Select WAN1 AAL5 Encap:

13.Select: or

14.Click

15.Enter User Name provided by ISP: user1@net

16.Enter Password provided by ISP: user1

17.Re-enterPasswordforconrmation:user1

18.The screen will prompt the new congured parameters. Check the param-

eters and click

. The router will reboot with the new setting or click

tocongureotherparameters.

Console Conguration

Do the following steps:

1. User: admin password: admin 

2. enable supervisor password: root 

3. setup mode Route 

4. wan Interface number (1~8): 1 

protocol PPPoA or PPPoE 

vpi_vci: 0 

32 

encap LLC 

isp account: user1@net 

password: user1 

Idle timeout (ENTER for default) <10>: 10

5. lan Interface number: 1 

6. address 192.168.0.1 

255.255.255.0 

attrib Virtual 

7. (back to root) write y 

y (reboot)

2.3 Routing Mode for IPoA or EoA

LAN IP 192.168.0.1

Mask 255.255.255.0

IP 192.168.0.2

Mask 255.255.255.0

Gateway 192.168.0.1

VPI = 0, VCI = 32

Encapsulation = LLC

BAS

DSLAM

ISP

WANLAN

GRT-101

Router Mode

WNA IP 10.1.2.1

Mask 255.255.255.0

Gateway 10.1.2.2

DNS 168.95.1.1

IP 10.1.2.2

Mask 255.255.255.0

Web UI Conguration

For Route Mode with Classical IP over ATM and Ethernet over ATM, follow the

following settings. First select and

, and then click for

setting other parameters.

1. Enter LAN IP: 192.168.0.1

2. Enter LAN Sub-net Mask: 255.255.255.0

3. Host Name: SOHO

4. DHCP Server: Enable

5. Click

Andere Handbücher für GRT-101

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Planet Netzwerk-Router Handbücher

Planet

Planet GS-5220-48T4X Bedienungsanleitung

Planet

Planet ADE-4301A Bedienungsanleitung

Planet

Planet WSD-800 Bedienungsanleitung

Planet

Planet EPN-102 Bedienungsanleitung

Planet

Planet MGSW SERIES Bedienungsanleitung

Planet

Planet GSW-2400HPS Bedienungsanleitung

Planet

Planet ADN-4100 Bedienungsanleitung

Planet

Planet WGSW-2620PV Bedienungsanleitung

Planet

Planet ADN-4100 Bedienungsanleitung

Planet

Planet ADE-4100 Bedienungsanleitung

Planet

Planet VR-100 Series Bedienungsanleitung

Planet

Planet Powerline Ethernet Bridge PL-104E Bedienungsanleitung

Planet

Planet FGSD-1022 Bedienungsanleitung

Planet

Planet FNSW-1600P Bedienungsanleitung

Planet

Planet ISW-802M Bedienungsanleitung

Planet

Planet SW-502 Bedienungsanleitung

Planet

Planet IAD-300 Bedienungsanleitung

Planet

Planet VRT-402N Bedienungsanleitung

Planet

Planet XRT-401F Bedienungsanleitung

Planet

Planet FGSW-2620PVM Series Bedienungsanleitung

Planet

Planet FGSW-2620VM Series Bedienungsanleitung

Planet

Planet ADSL 2/2+ VPN Firewall Router ADE-4300A/B Bedienungsanleitung

Planet

Planet XRT-401C Bedienungsanleitung

Planet

Planet Enterprise WiFi System Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise