Planet SOHOConnect Series Bedienungsanleitung

SOHOConnect Series

SW-500/ SW-800/ FSD-503/ FSD-803

5/8-port 10/100Mbps Fast Ethernet Switch

FCC Warning

This equipment has been tested and found to comply with the

regulations for a Class A digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with this

user’s guide, may cause harmful interference to radio

communications. Operation of this equipment in a residential

area is likely to cause harmful interference, in which case the

user will be required to correct the interference at his own

expense.

CE Mark Warning

In a domestic environment, this product may cause radio

interference, in which case the user may be required to take

adequate measures.

Trademarks

PLANET is a registered trademark of PLANET Technology

Corp. All other trademarks belong to their respective owners.

Contents subject to revision without prior notice.

Revision

User's manual for PLANET SOHOConnect Series Switch

Model: SW-500, SW-800, FSD-503, FSD-803

Rev: 2.0 (January. 2002)

Part No. EM-SW58V3

Table of Contents

About This Guide...........................................................................................4

Purpose...................................................................................................4

Terms/Usage...........................................................................................4

OverviewofthisUser

’s Guide..............................................................5

Chapter 1 Introduction....................................................................................6

Fast EthernetTechnology.......................................................................6

SwitchingTechnology............................................................................6

Features..................................................................................................7

Chapter 2 Unpacking and Setup...................................................................10

Unpacking............................................................................................10

Setup.....................................................................................................10

Chapter 3 Identifying External Components................................................11

Front Panel...........................................................................................11

RearPanel.............................................................................................12

LED Indicators.....................................................................................13

Chapter 4 Connecting The Switch................................................................15

PC to Switch.........................................................................................15

Hubto Switch.......................................................................................15

Hub without Uplink (MDI-II)port.......................................................16

Switch to Switches (other devices)......................................................17

Port Speed & Duplex Mode.................................................................17

Appendix ATechnicalSpecifications..........................................................18

Appendix B RJ-45 Pin Specification............................................................20

Appendix C Switch Operation.....................................................................22

Address Table.......................................................................................22

Learning................................................................................................22

Forwarding & Filtering........................................................................22

Store-and-Forward................................................................................23

Auto-Negotiation..................................................................................23

About This Guide

Congratulations on your purchase of SW-500/SW-800/FSD-503/

FSD-803, 5/8-port 10/100Mbps Fast Ethernet Switch. This device

integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network

capabilities in a highly flexible desktop package.

Purpose

This manual discusses how to install your SW-500/SW-800/

FSD-503 / FSD-803, 5/8-port 10/100Mbps Fast Ethernet

Switch.

Terms/Usage

In this guide, the term “Switch" (first letter upper case) refers

to your 5/8-port 10/100Mbps Ethernet Switch, and "switch"

(first letter lower case) refers to other Ethernet switches.

This guide provides the information you need to install and

configure the following models of the Switch:

•5-port 10/100Mbps Ethernet Switch

•8-port 10/100Mbps Ethernet Switch

Overview of this User’s Guide

Chapter 1, Introduction. Describes the Switch and its

features.

Chapter 2, Unpacking and Setup. Helps you get started with

the basic installation of the Switch.

Chapter 3, Identifying External Components. Describes the

front panel, rear panel and LED indicators of the Switch.

Chapter 4, Connecting The Switch. Tells how you can

connect the Switch to your Ethernet network.

Appendix A, Technical Specifications.Lists the technical

(general, physical and environmental, and performance)

specifications of the Switch.

Appendix B, RJ-45 Pin Specification.Describes the RJ-45

receptacle/connector and the straight and crossover cable

connector.

Appendix C, Switch Operation, Describes how the switch

work in details.

Chapter 1 Introduction

This chapter describes the features of the Switch and some

background information about Ethernet/Fast Ethernet switching

technology.

Fast Ethernet Technology

The growing importance of LANs and the increasing

complexity of desktop computing applications are fueling the

need for high performance networks. A number of high-speed

LAN technologies have been proposed to provide greater

bandwidth and improve client/server response times. Among

them, 100BASE-T (Fast Ethernet) provides a non-disruptive,

smooth evolution from the current 10BASE-T technology. The

non-disruptive and smooth evolution nature, and the

dominating potential market base, virtually guarantee cost

effective and high performance Fast Ethernet solutions in the

years to come.

100Mbps Fast Ethernet is a new standard specified by the

IEEE 802.3 LAN committee. It is an extension of the 10Mbps

Ethernet standard with the ability to transmit and receive data

at 100Mbps, while maintaining the CSMA/CD Ethernet

protocol. Since the 100Mbps Fast Ethernet is compatible with

all other 10Mbps Ethernet environments, it provides a

straightforward upgrade and takes advantage of the existing

investment in hardware, software, and personnel training.

Switching Technology

Another approach to pushing beyond the limits of Ethernet

technology is the development of switching technology. A

switch bridge Ethernet packets at the MAC address level of

the Ethernet protocol transmitting among connected Ethernet

or Fast Ethernet LAN segments.

Switching is a cost-effective way of increasing the total

network capacity available to users on a local area network. A

switch increases capacity and decreases network loading by

dividing a local area network into different segments, which

don’t compete with each other for network transmission

capacity.

The switch acts as a high-speed selective bridge between the

individual segments. The switch, without interfering with any

other segments, automatically forwards traffic that needs to

go from one segment to another. By doing this the total

network capacity is multiplied, while still maintaining the same

network cabling and adapter cards.

For Fast Ethernet networks, a switch is an effective way of

eliminating problems of chaining hubs beyond the

“two-repeater limit." A switch can be used to split parts of the

network into different collision domains, making it possible to

expand your Fast Ethernet network beyond the 205-meter

network diameter limit for 100BASE-TX networks. Switches

supporting both traditional 10Mbps Ethernet and 100Mbps

Fast Ethernet are also ideal for bridging between the existing

10Mbps networks and the new 100Mbps networks.

Switching LAN technology is a marked improvement over the

previous generation of network bridges, which were

characterized by higher latencies. Routers have also been

used to segment local area networks, but the cost of a router,

the setup and maintenance required make routers relatively

impractical. Today switches are an ideal solution to most

kinds of local area network congestion problems.

Features

The Switches were designed for easy installation and high

performance in an environment where traffic on the network

and the number of user increase continuously.

The Switches with their small, compact size were specifically

designed for small to middle workgroups. These Switches can

be installed where space is limited; moreover, they provide

immediate access to a rapidly growing network through a wide

range of user-reliable functions.

The Switches are ideal for deployment with multiple

high -speed servers for shared bandwidth 10Mbps or 100Mbps

workgroups. With the highest bandwidth 200Mbps (100Mbps

full-duplex mode), any port can provide workstations with a

congestion-free data pipe for simultaneous access to the

server.

The Switches are expandable by cascading two or more

switches together. As all ports support 200Mbps, the Switches

can be cascaded from any port and to any number of

switches.

The Switches are a perfect choice for site planning to upgrade

to Fast Ethernet in the future. Ethernet workgroups can

connect to the Switches now, and change adapters and hubs

anytime later without needing to change the Switches or

reconfigure the network.

The Switches combine dynamic memory allocation with

store-and-forward switching to ensure that the buffer is

effectively allocated for each port, while controlling the data

flow between the transmit and receive nodes to guarantee

against all possible packet loss.

The Switches are an unmanaged 10/100 Fast Ethernet Switch

that offers solutions in accelerating small Ethernet workgroup

bandwidth.

Other key features are:

•Uplink/ MDI-II (media dependent interface) port for Uplink

to another switch, hub or repeater.

•Store and forward switching scheme capability. As the

result of complete frame checking and error frame filtering,

this scheme prevents error packages from transmitting

among segments.

•N-Way Auto-negotiation for any port. This allows for

auto-sensing of speed (10/100Mbps) thereby providing

you with automatic and flexible solutions in your network

connections.

•Flow control for any port. This minimizes dropped packets

by sending out collision signals while the port’s receiving

buffer is full. Note that flow control is only available in

half-duplex mode.

•Data forwarding rate per port is at wire-speed for

100Mbps speed.

•Data forwarding rate per port is at wire-speed for 10Mbps

speed.

•Data filtering rate eliminates all error packets, runts, etc.,

per port at wire-speed for 100Mbps speed.

•Data filtering rate eliminates all error packets, runts, etc.,

per port at wire-speed for 10Mbps speed.

•Up to 1K active MAC address entry table per port with

self-learning and table-aging for the Switch

Chapter 2 Unpacking and Setup

This chapter provides unpacking and setup information for the

Switches.

Unpacking

Open the shipping cartons of the Switch and carefully

unpacks its contents. The carton should contain the following

items:

•One 5/8-port 10/100Mbps Ethernet Switch

•One external power adapter

•This User’s Guide

•Quick Installation Guide

If any item is found missing or damaged, please contact your

local reseller for replacement.

Setup

The setup of the Switch can be performed using the following

steps:

•The surface must support at least 1.5 Kg for the Switch.

•The power outlet should be within 1.82 meters (6 feet) of

the Switch.

•Visually inspect the DC power jack and make sure that it

is fully secured to the power adapter.

•Make sure that there is proper heat dissipation from and

adequate ventilation around the Switch. Do not place

heavy objects on the Switch.

Notice: To prevent from device damage, please use the bundled

AC Adapter before power on your Switch.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Planet Netzwerk-Router Handbücher

Planet

Planet PL-802 Bedienungsanleitung

Planet

Planet MGSW-2402 Bedienungsanleitung

Planet

Planet FGSW-2620 Bedienungsanleitung

Planet

Planet WGS3-24000 Bedienungsanleitung

Planet

Planet VDR-300NU Bedienungsanleitung

Planet

Planet VIP-462DG Bedienungsanleitung

Planet

Planet VRT-402N Bedienungsanleitung

Planet

Planet FGSW-2620PVM Series Bedienungsanleitung

Planet

Planet Enterprise WiFi System Bedienungsanleitung

Planet

Planet XRT-401F Bedienungsanleitung

Planet

Planet WDAP-C7210E Bedienungsanleitung

Planet

Planet FNSW-4800 Bedienungsanleitung

Planet

Planet 802.11g Wireless Access Point / Bridge... Bedienungsanleitung

Planet

Planet GSW-1600HP Bedienungsanleitung

Planet

Planet EPN-102 Bedienungsanleitung

Planet

Planet WGSD-10020 Bedienungsanleitung

Planet

Planet WGSW-2620HP Bedienungsanleitung

Planet

Planet Gaw9.2Z18-4 Bedienungsanleitung

Planet

Planet MH-3400 Bedienungsanleitung

Planet

Planet GSW-2400HPS Bedienungsanleitung

Planet

Planet GSW-1602SF Bedienungsanleitung

Planet

Planet GSW-2416 Bedienungsanleitung

Planet

Planet GS-5220-48T4X Bedienungsanleitung

Planet

Planet IGS-20040MT Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise