Planet CV-119/P2000 Bedienungsanleitung
L2 Web Smart Gigabit/10Gigabit Ethernet Switch
GS-2240 Series
Quick Installation Guide
Table of Contents
1. Introduction ............................................................................................... 3
2. Package Contents ....................................................................................... 4
3. Requirements ............................................................................................. 5
4. Terminal Setup ........................................................................................... 6
5. Logon to the Console .................................................................................. 7
6. ConguringIPAddressviatheConsole ........................................................ 8
7. SavingtheCongurationviatheConsole.....................................................10
8. Starting Web Management .........................................................................11
9. SavingCongurationviatheWeb ...............................................................14
10.RecoveringBacktoDefaultConguration ....................................................15
11. Customer Support.....................................................................................16
3
1. Introduction
Thank you for purchasing PLANET L2 Web Smart Gigabit/10Gigabit Ethernet
Switch.Thedescriptionofthismodelisshownbelow:
GS-2240-24T4X24-port10/100/1000T+4-port10GSFP+WebSmartSwitch
GS-2240-48T4X48-port10/100/1000T+4-port10GSFP+WebSmartSwitch
“Managed Switch” is used as an alternative name in this Quick Installation
Guide.
4
2. Package Contents
Open the box of the Managed Switch and carefully unpack it. The box should
containthefollowingitems:
zThe Managed Switch
zQuickInstallationGuide
zRJ45 to RS232 Cable
zRubberFeet
zTwoRack-mountingBracketswithAttachmentScrews
zPower Cord
zSFPDust-proofCaps
If any item is found missing or damaged, please contact your local reseller for
replacement.
5
3. Requirements
zWorkstations running Windows XP/2003/Vista/7/8/10/2008, MAC OS X or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
zSerial Port Connection(Terminal)
TheaboveWorkstationscomewithCOMPort(DB9)orUSB-to-RS232converter.
The above Workstations have been installed with terminal emulator, such as
HyperTerminalincludedinWindowsXP/2003.
Serial cable -- One end is attached to the RS232 serial port, while the other
endtotheconsoleportoftheManagedSwitch.
zEthernet Port Connection
Network cables--Usestandardnetwork(UTP)cableswithRJ45connectors.
The above PC is installed with Web browser and JAVA runtime environment
plug-in.
Note
It is recommended to use Internet Explore 8.0 or above to access
the Managed Switch. If the Web interface of the Managed Switch
is not accessible, please turn off the anti-virus software or firewall
and then try it again.
6
4. Terminal Setup
The GS-2240 switch series is equipped with a console interface for local switch
setup and maintenance. To congure the system, connect a serial cable to a COM
port on a PC or notebook computer and to the RJ45 type of the console port of
the Managed Switch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 4-1: Managed Switch Console Connectivity
A terminal program is required to make the software connection to the Managed
Switch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port should be
conguredas:
Baud: 115200
Databits: 8
Parity: None
Stopbits: 1
Flowcontrol: None
Figure 4-2: COM Port Conguration
7
5. Logon to the Console
Once the terminal is connected to the device, power on the Managed Switch and
the terminal will display “running testing procedures”. Then, the following message
asks to log-in user name and password. The factory default user name and
passwordareshownasfollows,andtheloginscreeninFigure5-1appears.
Username:admin
Password:admin
Figure 5-1: Managed Switch Console Login Screen
The user can now enter commands to manage the Managed Switch. For a detailed
descriptionofthecommands,pleaserefertothefollowingchapters.
Note
1.Forsecurity reason,pleasechange andmemorize the newpass-
wordafterthisfirstsetup.
2. Only accept command in lowercase letter under console inter-
face.
8
6.ConguringIPAddressviatheConsole
TheManagedSwitchisshippedwithdefaultIPaddressshownbelow:
IPAddress:192.168.0.100
SubnetMask:255.255.255.0
To check the current IP address or modify a new IP address for the Switch, please
usetheproceduresasfollows:
Show the current IP address
1.Atthe“GS-2240 Series#”prompt,enter“show ip interface vlan1 brief”.
2.The screen displays the current IP address, subnet mask and gateway as shown
inFigure6-1.
Figure 6-1: IP Information Screen
9
ConguringIPaddress
3.Atthe“GS-2240 Series#”prompt,enter“congure terminal”.
4.At the “GS-2240 Series(cong)#” prompt, enter the following command and
press <Enter>asshowninFigure6-2.
GS-2240Series(cong)# ip route 0.0.0.0/0 192.168.1.254
GS-2240Series(cong)# interface vlan1
GS-2240Series(cong-vlan1)# ip address 192.168.1.100/24
ThepreviouscommandwouldapplythefollowingsettingsfortheSwitch.
IPAddress:192.168.1.100
SubnetMask:255.255.255.0
Gateway:192.168.1.254
Figure 6-2: IP Address Screen
5.RepeatStep1tocheckiftheIPaddressischanged.
If the IP is successfully congured, the Managed Switch will apply the new IP
address setting immediately. You can access the Web interface of the GS-2240
Switch Series through the new IP address.
Note
If you are not familiar with console command or the related
parameter, enter “?” anytime in console to get the help descrip-
tion.
10
7.SavingtheCongurationviatheConsole
In the switch, the running conguration le is stored in the RAM. In the current
version, the running conguration sequence of running-cong can be saved from
the RAM to FLASH by writing the command or copying the running-cong
startup-cong command, so that the running conguration sequence becomes
thestartupcongurationle,whichiscalledcongurationsave.
1.At the “GS-2240 Series#” prompt, enter “copy running-cong startup-
cong” asshowninFigure7-1.
Figure 7-1: The Conguration Screen
Inhaltsverzeichnis
Andere Planet Schalten Handbücher
Planet
Planet MII Series Bedienungsanleitung
Planet
Planet FSD-1008HP Bedienungsanleitung
Planet
Planet NOVA100 Series Bedienungsanleitung
Planet
Planet MGSW-004 Bedienungsanleitung
Planet
Planet IAP-2000PE Bedienungsanleitung
Planet
Planet FNSW-1600 Bedienungsanleitung
Planet
Planet USB 2.0 External Hub UH-421 Bedienungsanleitung
Planet
Planet FNSW-1608PS Bedienungsanleitung
Planet
Planet NOVASwitch FNSW-8086F Bedienungsanleitung
Planet
Planet GSD-1603 Bedienungsanleitung
Planet
Planet WGSW-48040HP Bedienungsanleitung
Planet
Planet WSD-800 Bedienungsanleitung
Planet
Planet WGs-4215-8HP2S Bedienungsanleitung
Planet
Planet GS-5220 Series Bedienungsanleitung
Planet
Planet Palm-Top EH-501 Bedienungsanleitung
Planet
Planet GS-4210-8UP2S Bedienungsanleitung
Planet
Planet GSW-1600HP Bedienungsanleitung
Planet
Planet GSD-805 Bedienungsanleitung
Planet
Planet KVM-U201 Bedienungsanleitung
Planet
Planet Switch Bedienungsanleitung
