Planet IGS-5225-4T2S Bedienungsanleitung

Industrial L2+ Multi-Port Full Gigabit

Managed Ethernet Switch

IGS-5225-4T2S/IGS-5225-4P2S/IGS-5225-4UP1T2S

IGS-5225-8P4S/IGS-5225-8P4S-12V/IGS-5225-8P2T2S

IGS-5225-8P2T4S

Quick Installation Guide

Table of Contents

1. Package Contents................................................................................. 3

2. Requirements....................................................................................... 5

3. Wiring the Power Inputs ....................................................................... 6

3.1 Grounding the Device..................................................................... 8

4. Terminal Setup..................................................................................... 9

4.1. Logging on to the Console............................................................ 10

 4.2 ConguringIPAddress ................................................................. 11

5. Starting Web Management .................................................................. 13

5.1 Logging in to the Industrial Managed Switch .................................. 13

 5.2 SavingCongurationviaWeb ....................................................... 15

6. RecoveringBacktoDefaultConguration ............................................. 16

7. Customer Support .............................................................................. 19

1. Package Contents

Thank you for purchasing PLANET L2+ Industrial Managed Switch, IGS-5225

Series. The number of the ports of these models is as follows:

GbECopper

Ports

PoEPorts GbESFPPorts

at/af bt* 1G 2.5G*

IGS-5225-4T2S 4- - - 2

IGS-5225-4P2S 4 4 -2-

IGS-5225-4UP1T2S 5-4-2

IGS-5225-8P4S 8 8 -2 2

IGS-5225-8P4S-12V 8 8 -2 2

IGS-5225-8P2T2S 10 8- - 2

IGS-5225-8P2T4S 10 8-2 2

*bt:Compatiblewith802.3at/afPoE

*2.5G:Compatiblewith1000BASE-SX/LX/BXSFPtransceiver

“Industrial Managed Switch” mentioned in this Quick Installation Guide

refers to the above models.

Open the box of the Industrial Managed Switch and carefully unpack it.

The box should contain the following items for each model of the Industrial

Managed Switches:

The

Industrial

Managed

Switch

Quick

Installation

Guide

Sheet

Wall

Mounting

Kit

DB9 to

RJ45,

RS232

Console

Cable

RJ45

Dust

Cap

SFP

Dust

Cap

IGS-5225-

4T2S     5 2

IGS-5225-

4P2S     5 2

IGS-5225-

4UP1T2S     6 2

IGS-5225-

8P4S     9 4

IGS-5225-

8P4S-12V     9 4

IGS-5225-

8P2T2S     11 2

IGS-5225-

8P2T4S     11 4

If any of these are missing or damaged, please contact your dealer

immediately. If possible, retain the carton including the original packing

materials to enable you to repack the product in case there is a need to return

it to us for repair.

2. Requirements

The Industrial Managed Switch provides remote login interface for

management purposes. The following equipment is necessary for further

management:

zWorkstations running Windows 10/11, MAC OS 10.15 or later, Linux, UNIX,

or other platforms are compatible with TCP/IP protocols.

zWorkstationsareinstalled withEthernetNIC(NetworkInterfaceCard)

zSerialPortConnection(Terminal)

 The above Workstations come with COM Port (DB9) or USB-to-RS232

converter.

 The above Workstations have been installed with terminal emulator, such

as putty or tera term.

 Serial cable -- one end is attached to the RS232 serial port, while the

other end to the console port of the Industrial Managed Switch.

zEthernetPortConnection

 Network cables -- Use standard network (UTP) cables with RJ45 connec-

tors.

The above PC is installed with Web browser.

It is recommended to use Chrome 98.0.xxx or above to access

the Industrial Managed Switch.

3. Wiring the Power Inputs

The Upper Panel of the Industrial Managed Switch comes with one

6-contact terminal block. Please follow the steps below to insert the power

wire.

1.Insert positive/negative DC power wires into Contacts 1 and 2 for Power 1,

or Contacts 5 and 6 for Power 2.

IGS-5225-8P4S/IGS-5225-8P2T2S/IGS-5225-8P2T4S:DC48~54V

PWR1 PWR2

Alarm

DI1 DO0 DO1DI0 GNDGND

DC Input:

48-54V , 6A max.

Max. Fault Alarm Loading: 24V, 1A

1 2 3 4 5 6

Figure 3-1: IGS-5225-8P4S/IGS-5225-8P2T2S/IGS-5225-8P2T4S Upper Panel

IGS-5225-4UP1T2S:DC48~54V

DI1 DO0 DO1DI0 GNDGND

DC Input:

48-54V , 8.3A max.

Dual power input is required

for maximum PoE loading.

Refer to user’s manual for

more details.

PWR1 Alarm PWR2

V1+ V2+

Max. Fault Alarm Loading: 24V, 1A

1 2 3 4 5 6

Earth Ground

Figure 3-2: IGS-5225-4UP1T2S Upper Panel

IGS-5225-4T2S:DC12~48V,AC24V

Max. Fault Alarm Loading: 24V, 1A

DC Input: 12-48V

, 1.7A max.

AC Input: 24V

, 1A max.

V1+ V2+

PWR1 PWR2Alarm

1 2 3 4 5 6

Figure 3-3: IGS-5225-4T2S Upper Panel

IGS-5225-4P2S:DC48~56V

FaultPWR1

V1+ V2+

PWR2

Max. fault loading: 24V, 1A

DC Input: 48-56V

3.5A max.

1 2 3 4 5 6

Figure 3-4: IGS-5225-4P2S Upper Panel

IGS-5225-8P4S-12V:DC12~54V

PWR1 PWR2

Alarm

DI1 DO0 DO1DI0 GNDGND

DC Input:

12-54V , 6A max.

Max. Fault Alarm Loading: 24V, 1A

1 2 3 4 5 6

Figure 3-5: IGS-5225-8P4S-12V Upper Panel

2.Tightenthewire-clampscrewsforpreventingthewiresfromloosening.

123456

V+ V- V+ V-

Power 1 Power 2

Positive(+)Pin Negative(-)Pin

IGS-5225Series Pin 1/5 Pin 2/6

1. The wire gauge for the terminal block should be in the range

from 12 to 24 AWG.

2.Please check the wire AWG Ampere specification before

connectingPLANETIndustrialManagedSwitch.

PWR1 and PWR2 must provide the same DC voltage for pow-

er load balance while operating with dual power input.

3.1 Grounding the Device

Users MUST complete grounding wired with the device; otherwise, a sudden

lightning could cause fatal damage to the device.

PWR1 PWR2

Alarm

DI1 DO0 DO1DI0 GNDGND

DC Input:

48-54V , 6A max.

Max. Fault Alarm Loading: 24V, 1A

1 2 3 4 5 6

EMD(Lightning)damageisnotcoveredunderwarranty.

4. Terminal Setup

To congure the system, connect a serial cable to a COM port on a PC or

notebook computer and to RJ45 type serial (console) port of the Industrial

Managed Switch. The console port of the Industrial Managed Switch is DCE

already, so that you can connect the console port directly through PC without

the need of null modem.

PC/Workstation with

Terminal Emulation Software

RJ45 to DB9 RS232 Cable

Serial Port

Console Port

115200,N,8,1

IGS Industrial Managed Switch

Console

115200,N,8,1

P1 P2 Fault

DIDO

Ring

R.O.

PoE Usage

ACT1000 LNK

ACT100 LNK

A terminal program is required to make the software connected to the

IGS-5225seriesIndustrialManagedSwitch.

1. Run terminal program on the OS.

2.When the followingscreenappears,makesurethatthe COM port should be

conguredas:

Baud: 115200

Parity:None

Data bits: 8

Stop bits: 1

Flowcontrol:None

4.1. Logging on to the Console

Once the terminal has been connected to the device, power on the Industrial

Managed Switch and the terminal will display “running testing procedures”.

The following console screen is based on the IGS-

5225-4UP1T2S. The display of the other IGS-5225 series is the

sameasthatoftheIGS-5225-4UP1T2S.

Then, the following message asks to log in user name and password. The

default user name and password are shown as follows and the login screen in

Figure4-1appears

Username:admin

Password: admin

Figure 4-1: Console Login Screen

The user can now enter commands to manage the Industrial Managed Switch.

For a detailed description of the commands, please refer to the following

chapters.

1.For security reason, please change and memorize the

new password after this first setup.

2. Only accept command in lowercase letter under console inter-

face.

Andere Handbücher für IGS-5225-4T2S

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Planet Schalten Handbücher

Planet

Planet IGS-501T Bedienungsanleitung

Planet

Planet XGS3-24042 Bedienungsanleitung

Planet

Planet GS-4210-8UP2S Bedienungsanleitung

Planet

Planet WGSW-52040 Bedienungsanleitung

Planet

Planet WGSW-24040 Bedienungsanleitung

Planet

Planet GSD-Series Bedienungsanleitung

Planet

Planet WGS-4215-8P2S Bedienungsanleitung

Planet

Planet Switch Bedienungsanleitung

Planet

Planet KVM-U201 Bedienungsanleitung

Planet

Planet GSW-601S Bedienungsanleitung

Planet

Planet SW-502 Bedienungsanleitung

Planet

Planet GS-5220-8UP2T2X Bedienungsanleitung

Planet

Planet WGSW-2840 Bedienungsanleitung

Planet

Planet WGSD-1022 Bedienungsanleitung

Planet

Planet MGSW-004-12F Bedienungsanleitung

Planet

Planet FNSW-4800 Bedienungsanleitung

Planet

Planet FNSW-1608PS Bedienungsanleitung

Planet

Planet MGSW SERIES Bedienungsanleitung

Planet

Planet IKVM-8000 Bedienungsanleitung

Planet

Planet IPOE-270 Bedienungsanleitung

Planet

Planet WGSW-20160HP Bedienungsanleitung

Planet

Planet IGS-4215-8UP4X Bedienungsanleitung

Planet

Planet GSD-604HP Bedienungsanleitung

Planet

Planet KVM-200 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung