Planet Network Device WAP-4033PE Bedienungsanleitung

54Mbps PoE Access Point

WAP-4033PE

User’s Manual

be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or

computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,

manual or otherwise, without the prior written permission of PLANET.

PLANET makes no representations or warranties, either expressed or implied, with respect to the

contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular

purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove

defective following their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes

the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting

from any defect in the software. Further, PLANET reserves the right to revise this publication and to

make changes from time to time in the contents hereof without obligation to notify any person of such

revision or changes.

All brand and product names mentioned in this manual are trademarks and/or registered trademarks of

their respective holders.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

1.Reorient or relocate the receiving antenna.

2.Increase the separation between the equipment and receiver.

3.Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

4.Consult the dealer or an experienced radio technician for help.

FCC Caution

To assure continued compliance. (example-use only shielded interface cables when connecting to

computer or peripheral devices). Any changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two

conditions: ( 1 ) This device may not cause harmful interference, and ( 2 ) this Device must accept any

interference received, including interference that may cause undesired operation.

Federal Communication Commission (FCC) Radiation Exposure

Statement

This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In

order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to

the antenna shall not be less than 20 cm (8 inches) during normal operation.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN

PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication

terminal Equipment and the mutual recognition of their conformity (R&TTE)

The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal

Equipment and Satellite Earth Station Equipment) As of April 8,2000.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it. However,

special attention must be paid to the dangers of electric shock and static electricity when working with

electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed

at all times to ensure the safe use of the equipment.

EU Countries Not Intended for Use

The ETSI version of this device is intended for home and office use in Austria Belgium, Denmark,

Finland, France (with Frequency channel restrictions). Germany, Greece, Ireland, Italy,

Luxembourg .The Netherlands, Portugal, Spain, Sweden and United Kingdom.

The ETSI version of this device is also authorized for use in EFTA member states Iceland,

Liechtenstein, Norway and Switzerland.

Potential restrictive use

France: Only channels 10,11,12 and 13

WEEE regulation

To avoid the potential effects on the environment and human health as a result of the

presence of hazardous substances in electrical and electronic equipment, end users of

electrical and electronic equipment should understand the meaning of the crossed-out

wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to

collect such WEEE separately.

Revision

User’s Manual for PLANET 54Mbps PoEAccess Point

Model: WAP-4033PE

Rev: 1.0 (Oct, 2006)

Part No. EM-WAP4033PE

TABLE OF CONTENTS

Chapter 1 Introduction ..................................................................................7

1.1 Package Contents.................................................................................................... 7

1.2 System Requirements.............................................................................................. 7

1.3 Features................................................................................................................... 8

1.4 LED Indicators.......................................................................................................... 8

1.5 Wireless Performance.............................................................................................. 8

1.6 Reset Button............................................................................................................. 9

Chapter 2 Hardware Installation.................................................................10

Chapter 3 Web Configuration .....................................................................11

3.1 Home.......................................................................................................................11

3.2 Basic Setting .......................................................................................................... 12

3.2.1 AP Mode.....................................................................................................................12

3.2.2 Station - Ad Hoc Mode................................................................................................14

3.2.3 Station - Infrastructure Mode......................................................................................16

3.2.4 AP Bridge - Point to Point Mode.................................................................................17

3.2.5 AP Bridge - Point to Multipoint Mode..........................................................................18

3.2.6 AP Bridge - WDS Mode..............................................................................................19

3.2.7 Universal Repeater Mode...........................................................................................21

3.2.8 Security setting of bridge mode..................................................................................22

3.3 Advanced Settings ................................................................................................. 24

3.4 Security .................................................................................................................. 25

3.4.1 802.1x.........................................................................................................................26

3.4.2 WEP...........................................................................................................................27

3.4.3 WPA pre-shared key...................................................................................................28

3.4.4 WPA RADIUS.............................................................................................................30

3.5 MAC Filtering.......................................................................................................... 31

3.6 System Utility.......................................................................................................... 32

3.7 Configuration Utility................................................................................................ 33

3.8 Upgrade.................................................................................................................. 34

3.9 Reset...................................................................................................................... 35

Chapter 4 Specification...............................................................................36

Chapter 5 Frequently Ask Question...........................................................37

Chapter 1 Introduction

Thank you for purchasing WAP-4033PE. The WAP-4033PE supports both IEEE 802.11b and IEEE

802.11g standards. You can use it to connect an existing WLAN, or to build up a new wireless LAN.

Except for essential AP mode, WAP-4033PE also provides AP Client/ Bridge/ Repeater and WDS

(Wireless Distributed System) modes to accommodate all kinds of network topology. High data rate (up to

54Mbps) support allows faster communication between LAN and WLAN. Maximize network efficiency

while minimizing your network investment and maintenance costs. With the PoE (IEEE802.3af) interface,

users can easily connect this AP to anywhere.

Supports WPA, WPA2, WEP and MAC address filter function to consolidate the wireless network security,

you can prevent unauthorized wireless stations from accessing your wireless network.

This product provides a friendly user interface and allows users to configuring from web browser. Without

utility install, user doesn’t need to find the utility for this product in lots of program list, it can be configured

in different OS that has provide web browser.

1.1 Package Contents

Make sure that you have the following items:

z1 x WAP-4033PE

z1 x Power Adapter

z1 x User’s Manual CD

z1 x Quick Installation Guide

z1 x External Antenna

Note: If any of the above items are missing, contact your supplier as soon as

possible.

1.2 System Requirements

Before installation, please check the following requirements with your equipment.

zPentium Based (or above) IBM-Compatible PC System

zCD-ROM drive

zWindows 98/Me/NT/2000/XP/Server2003 Operating System with TCP/IP protocol

1.3 Features

zComplies with the IEEE 802.11b/g (DSSS) 2.4GHz specification

zSupports 2.400~2.4835 GHz frequency band

zData rate supports up to 54Mbps

zIEEE 802.3af compliant

zAuto rate fallback in case of obstacles or interferences

zSupports WEP/WPA-PSK/WPA/WPA2 encryption

zSupports AP/ AP Client/ Bridge/ Repeater and WDS (Wireless Distributed System) mode

zSeamlessly integrate wireless and wired Ethernet LAN networks

zProvides MAC Filter function

zBuilt-in DHCP server

zSupport Auto-MDI/MDI-X

zWeb-based configuration

1.4 LED Indicators

LED Color Function

PWR Green Off: Power is not connected

On: Device is ready

Blink: During boot up procedure

WLAN Green Off: Wireless LAN is no function

Blink: Transmitting or receiving data through the Wireless LAN

LAN Green Off: LAN is not connected

On: LAN is connected

Blink: Transmitting or receiving data through the LAN

1.5 Wireless Performance

The following information will help you utilizing the wireless performance and operating coverage of

WAP-4033PE.

1. Site selection

To avoid interferences, please locate WAP-4033PE and wireless client away from transformers,

microwave ovens, heavy-duty motors, fluorescent lights and other industrial equipments. Keep the

number of walls or ceilings between AP and clients as few as possible. Otherwise the signal strength

may be seriously reduced. Place WAP-4033PE in a open space or add additional WAP-4033PE as

needed to improve the coverage.

2. Environmental factors

The wireless network is easily affected by many environment factors. Every environment is unique

with different obstacles, construction materials, weather, etc. It is hard to determine the exact

operation rage of WAP-4033PE in a specific location without testing.

3. Antenna adjustment

The bundle antenna of WAP-4033PE is adjustable. Firstly install the antenna pointing straight up,

then smoothly adjust it if the radio signal strength is poor. But the signal reception is definitely weak

in some certain areas, such as location right down the antenna.

Moreover, the original antenna of WAP-4033PE can be replaced with other external antennas to

extend the coverage. Please check the specification of the antenna you want to use, and make sure

it can be used on WAP-4033PE.

4. WLAN Type

If WAP-4033PE is installed in an 802.11b and 802.11g mixed WLAN, its performance will reduced

significantly. Because every 802.11g OFDM packet needs to be preceded by an RTS-CTS or CTS

packet exchange that can be recognized by legacy 802.11b devices. This additional overhead

lowers the speed. If there are no 802.11b devices connected, or if connections to all 802.11b devices

are denied so that WAP-4033PE can operate in 11g-only mode, then its data rate should actually

54Mbps.

1.6 Reset Button

WAP-4033PE provides a Reset button on the rear panel for user to reset or set WAP-4033PE

configuration to factory default by hardware.

Time Active

Press less than 5 Sec. WAP-4033PE will re-boot itself, keeping your original configurations

Press more than 5 Sec. WAP-4033PE will reset itself to the factory default settings

Chapter 2 Hardware Installation

Before you proceed with the installation, it is necessary that you have enough information about the

WAP-4033PE.

1. Locate an optimum location for the WAP-4033PE. The best place for your WAP-4033PE is

usually at the center of your wireless network, with line of sight to all of your mobile stations.

2. Assemble the antenna to WAP-4033PE. Try to place them to a position that can best cover your

wireless network. The antenna’s position will enhance the receiving sensitivity.

3. Connect RJ-45 cable to WAP-4033PE. Connect this WAP-4033PE to your LAN switch/hub or a

single PC. If the connected device is IEEE802.3af compliant switch, the WAP-4033PE will power

on. You will not need to plug-in the power adapter in next step.

4. Plug in power adapter and connect to power source. After power on, WAP-4033PE will start to

work.

Note: ONLY use the power adapter supplied with the WAP-4033PE. Otherwise, the product may

be damaged. If you want to reset your WAP-4033PE to default settings, press the Reset

button 5 second. Then release the button and wait for 10 seconds for rebooting.

Andere Handbücher für Network Device WAP-4033PE

Inhaltsverzeichnis

Andere Planet Drahtloser Zugangspunkt Handbücher

Planet

Planet WAP-3000 Bedienungsanleitung

Planet

Planet WAP-4000A Bedienungsanleitung

Planet

Planet WDAP-C7200AC Bedienungsanleitung

Planet

Planet WBS-202N Bedienungsanleitung

Planet

Planet WNAP-6305 Bedienungsanleitung

Planet

Planet RTL8812AU-CG Bedienungsanleitung

Planet

Planet MAP-3100 Kurzanleitung

Planet

Planet WNAP-7350 Bedienungsanleitung

Planet

Planet EPN-402NV Bedienungsanleitung

Planet

Planet WNAP-6350 Bedienungsanleitung

Planet

Planet WDAP-C7200AC Bedienungsanleitung

Planet

Planet WNAP-7205 Bedienungsanleitung

Planet

Planet WAP-1965 Bedienungsanleitung

Planet

Planet WAPC-1232HP Bedienungsanleitung

Planet

Planet WAP-252N Bedienungsanleitung

Planet

Planet WAP-4030A Bedienungsanleitung

Planet

Planet WAP-1963 Bedienungsanleitung

Planet

Planet WBS-502AC Bedienungsanleitung

Planet

Planet WAP-4033 Bedienungsanleitung

Planet

Planet IAP-1800AX Bedienungsanleitung

Planet

Planet WDAP-C1750 Bedienungsanleitung

Planet

Planet WAP-4036 Bedienungsanleitung

Planet

Planet WDAP-C1800AX Bedienungsanleitung

Planet

Planet WAP-252N Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung