Planet Network Device WAP5 Bedienungsanleitung

802.11b WLAN Outdoor AP

WAP-5000

User sManual

be reproduced, transmitted, transcribed, stored in aretrieval system, or translated into any language

or computer language,in any form or by any means,electronic, mechanical,magnetic, optical,

chemical, manual or otherwise, without the prior written permission of PLANET.

PLANETmakes no representations orwarranties, either expressed orimplied, with respectto the

contentshereof and specifically disclaims any warranties, merchantability or fitness for any particular

purpose.Any software described in this manual is sold or licensed "as is".Should the programs

prove defective following their purchase, the buyer (and not this company,itsdistributor,or itsdealer)

assumes the entire cost of all necessary servicing, repair,and any incidental or consequential

damages resulting from any defect in the software. Further, this company reserves the right to revise

this publication and to make changes from time totime in the contentshereof withoutobligation to

notify any person ofsuch revision orchanges..

All brand and product names mentioned in this manual are trademarks and/or registered trademarks

of their respective holders.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limitsfor aClass Bdigital device,

pursuant toPart 15 of FCC Rules.These limitsaredesigned toprovide reasonable protection

against harmful interference in aresidential installation. This equipment generates, uses, and can

radiateradio frequency energyand, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However,there is no guarantee that

interference will not occur in aparticularinstallation.If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment offand

on, the user is encouraged to try to correct the interference by one or more of the following measures:

1.Reorientor relocate the receiving antenna.

2.Increase the separation between the equipmentand receiver.

3.Connect the equipment into an outlet on acircuit different from that to which the receiver is

connected.

4. Consult the dealer or an experienced radio technician forhelp.

FCC Caution:

Toassurecontinued compliance.(example-use only shielded interface cables when connecting to

computeror peripheral devices). Any changes or modifications not expressly approved by the party

responsible for compliance could void the user s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject tothe Following two

conditions: (1) This device may not cause harmful interference, and (2 )this Device must accept any

interference received, including interference thatmay cause undesired operation.

Federal Communication Commission(FCC) Radiation Exposure

Statement

This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In

orderto avoid the possibility of exceeding the FCC radio frequency exposure limits,human proximity

to the antenna shall not be less than 20 cm(8 inches) during normal operation.

R&TTE Compliance Statement

This equipmentcomplies with all the requirementsof DIRECTIVE 1999/5/CE OF THE EUROPEAN

PARLIAMENTAND THE COUNCILOF 9March 1999 on radio equipment and telecommunication

terminal Equipment and the mutual recognition of theirconformity (R&TTE)

The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal

Safety

This equipment is designed with the utmost care for the safety of those who install and use it.However,

special attention must be paid to the dangers of electric shock and static electricity when working with

electrical equipment.All guidelines of this and of the computer manufacture must thereforebe allowed

at all times to ensure the safe use of the equipment.

Revision

User s Manual for PLANET802.11b WLAN Outdoor AP

Model: WAP-5000

Rev: 1.0 (January, 2004)

Part No. EM-WAP5K

TABLE OF CONTENTS

CHAPTER 1 INTRODUCTION..................................................................................................1

1.1 PACKAGE CONTENTS .........................................................................................................1

1.2 SYSTEM REQUIREMENTS....................................................................................................1

1.3 FEATURES .........................................................................................................................2

1.4 SPECIFICATION ..................................................................................................................2

1.5 WIRELESS PERFORMANCE .................................................................................................3

CHAPTER 2 HARDWAREINSTALLATION.............................................................................4

CHAPTER 3 PLANETOUTDOOR WLAN MANAGEMENTSYSTEM.....................................7

3.1 INTRODUCTION ..................................................................................................................7

3.2 INSTALLATION ....................................................................................................................7

3.3 USING PLANET OUTDOOR WMS....................................................................................10

3.3.1Kick Start................................................................................................................11

3.3.2Hosts View.............................................................................................................14

3.3.3 Trap View................................................................................................................32

CHAPTER 4 TROUBLESHOOTING.......................................................................................33

- 1 -

Chapter 1 Introduction

WAP-5000 is an IEEE 802.11b Wireless Outdoor Access Point.The special designed housing allows

WAP-5000 tobe installed in exposed locations under the rigorous weather conditions including heavy

rain, wind,and snow.Except for 64/128bit WEPencryption, WAP-5000 also integrates 802.1X

authentication. Cooperating with aRADIUS server can make your wireless LAN more secure than ever.

Provided with SNMP-based utility,WAP-5000 is easy to be installed and managed.The POE (Power

Over Ethernet) design reduces power cables installation cost and offersmore flexibility when selecting

the location of WAP-5000.Withall these advanced features,WAP-5000 is the ideal solution foroutdoor

networks.

1.1 Package Contents

Make sure that you have the following items:

• WAP-5000 x1

• Power Adapter x1

• DC injector x1

• Mounting kit x1

• 25m CAT5 cable with RJ-45 plug and ODU connector x1

• 0.3m N-type to N-type cable x1

• Quick Installation Guide x1

• Utility and User's manual CD x 1

Note:

If any of the above items are missing, contact your supplier as

soon as

possible.

1.2 System Requirements

Before installation, please check the following requirementswith your equipment.

• An x86-based microcomputer running Microsoft Windows 95, 98, Me, NT 4.0, 2000, orXP

• Microsoft Internet Explorer 4.01 or later

• A connection to an Ethernet network

Particular versions of Windows have the following additional requirements:

1. On Windows95,Microsoft DCOM95 must be installed.You can obtain DCOM95 from the

following Microsoft Web page:

http://www.microsoft.com/com/dcom/dcom95/download.asp

DCOM95 can also be found on the Microsoft Visual Basic 5.0 CD-ROM(Enterprise,

Professional,or Standard edition), in the directory \Pro\Tools\DCOM95.

2. On Windows98 (with the exception of Windows98SE,which already includes this

component), Microsoft DCOM98 must be installed. You can use the following link to

download it:

http://www.microsoft.com/com/dcom/dcom98/download.asp

3. On Windows NT 4.0, Service Pack 4 or latermust be installed.

- 2 -

1.3 Features

Wireless LAN IEEE802.11b compliant

Solid housing provides protection against rigorous weatherconditions

Strong network security with 802.1Xauthentication, 64/128-bit WEP encryption, user isolation,

protocol filtering, and MAC access control

One detachable N-type female connectors can connectto external antenna for expanding

connection distance

5 levels of adjustable transmit power control

High speed data transfer rateup to 11Mbps

Auto fall-back data rate forlong-distance communication and noisy environments

Provide powerful Windows-base SNMP utility forinstallation and management

Support DHCPClient

Power over Ethernet design

1.4 Specification

Model WAP-5000

StandardIEEE 802.11b

Signal Type DSSS (Direct Sequence Spread Spectrum)

Modulation BPSK, QPSK, CCK

Port 10Base-TX(RJ-45) * 1

Antenna ConnectorN-type Female * 1

Output Power 5 levels adjustable

100mW,50mW, 30mW,10mW, and 5mW

Sensitivity -84dBm

Operating Mode AP

Security

64/128-bitWEP encryption

Password protect

802.1Xsecurity

MAC filtering

SSID BroadcastDisable function

Protocol filtering

User isolation

Frequency Band 2.4 –2.484GHz

Data Rate Up to 11Mbps (1/2/5.5/11)

Dimensions (L x WxH) 165 x135 x55mm

Weight 1130g

Environmental Specification

Operating temperature: -20 –70 degree C

- 3 -

Storage temperature: -30 –80 degree C

Relative humanity: 5% –95% (non-condensing)

Power Requirement 12V DC, 2.0A

Electromagnetic

Compatibility FCC, CE

1.5 WirelessPerformance

The following information will help you utilizing the wireless performance, and operating coverage of

WAP-5000.

1. Site selection

To avoid interferences,please locate WAP-5000 and wireless clients away from transformers,

microwave ovens, heavy-duty motors, refrigerators, fluorescent lights, and other industrial

equipments.Keep the numberof walls, or ceilings between AP and clients as fewas possible;

otherwise the signal strength may be seriously reduced. Place WAP-5000 in open space or add

additional WAP-5000 as needed to improve the coverage.

2. Environmental factors

The wireless network is easily affected by many environmental factors. Every environment is

unique with different obstacles, construction materials, weather, etc. Itis hard to determine the

exact operating range of WAP-5000 in a specific location without testing.

3. Antenna adjustment

Please check the specification of the antenna you want to use, and make sure it can be used on

WAP-5000.

- 4 -

Chapter 2 Hardware Installation

Before you proceed with the installation, it is necessary that you have enough information about the

WAP-5000.

1. Locate an optimum location for the WAP-5000.

2. Assemble the antennas to WAP-5000.Try to place them toaposition that can best cover your

wireless network. The antenna sposition will enhance the receiving sensitivity.

3. Using provided CAT5 waterproof cable; connect the waterproof connector port of the WAP-5000

to the ODU port ofDC Injector.

4. Using Category 3 orhigher UTPor STPcable, connectthe RJ-45 port of DC Injector to a 10Mbps

or 10/100Mbps Ethernet hub or switch, and connect the management station to ahub or switch on

the same LAN.

5. Connect the output cordof power adapter tothe DC Injector sDC input jack, and plug it into an AC

outlet to power up the WAP-5000.

6. Connect the green grounding wire on WAP-5000 to the same grounding system with the ACwall

outlet. The grounding system mustcomply with the National Electrical Code and safety standards

that apply in your country.Always check with aqualified electrician ifyou are in doubtas to

whether your outdoor installation is properly grounded.

Note: ONLYuse the power adapter supplied with the WAP-5000. Otherwise, the product may be

damaged.

- 5 -

OUTDOOR INSTALLATION WARNING

IMPORTANTSAFETY PRECAUTIONS:

LIVES MAYBE ATRISK! Carefully observe these instructions and any special instructions that are

included with the equipment you are installing.

CONTACTING POWER LINESCANBE LETHAL. Make sure no power lines are anywhere where

possible contact can be made. Antennas, masts, towers,

guy wires orcables may lean or fall and contactthese

limes. People may be injured or killed if they are touching

or holding any partof equipment when it contactselectric

lines. Make sure there is NO possibility that equipment or

personnel can come in contact directly orindirectly with

power lines.

Assume all overhead lines are power lines.

The horizontal distance from a tower, mast or antenna to the nearest power line should be at least twice

the total length of the mast/antenna combination. This will ensure thatthe mast will notcontact power ifit

falls either during installation or later.

TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING ATHEIGHTS ABOVE GROUND.

l Select equipmentlocations that will allowsafe, simple equipment installation.

l Don t work alone.A friend or co-worker can save yourlife ifan accident happens.

l Use approved non-conducting lasersand other safety equipment.Make sure all equipment is in

good repair.

l If a tower or mast begins falling, don t attempt to catch it. Stand back and let it fall.

l If anything such as awire or mastdoes come in contactwith apower line, DON TTOUCH IT

OR ATTEMPT TO MOVE IT. Instead, save your life by calling the power company.

l Don t attempt to erect antennas or towers on windy days.

MAKE SUREALL TOWERS AND MASTS ARE SECURELYGROUNDED, AND ELECTRICAL

CABLES CONNECTED TO ANTENNASHAVE LIGHTNING ARRESTORS. This will help prevent fire

damage or human injury in case oflightning, static build-up,or short circuit within equipment connected

to the antenna.

l The base of the antenna mast or tower must be connected directly to the building protective

ground or to one or more approved grounding rods, using 1OAWGground wire and

- 6 -

corrosion-resistant connectors.

l Refer to the National Electrical Code forgrounding details.

IF APERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND CANNOT MOVE:

l DON T TOUCH THAT PERSON, OR YOU MAYBE ELECTROCUTED.

l Use anon-conductive dry board, stick or rope to push ordrag them so they no longerare in

contact with electrical power.

Once they are no longer contacting electrical power,administer CPR if you are certified, and make sure

that emergency medical aid has been requested.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Planet Drahtloser Zugangspunkt Handbücher

Planet

Planet WNAP-1110 Bedienungsanleitung

Planet

Planet WAP-4060PE Bedienungsanleitung

Planet

Planet WNAP-6305 Bedienungsanleitung

Planet

Planet IAP-1800AX Bedienungsanleitung

Planet

Planet WAP-1965 Bedienungsanleitung

Planet

Planet WAP-4030 Bedienungsanleitung

Planet

Planet EPN-402NV Bedienungsanleitung

Planet

Planet WAP-1963 Bedienungsanleitung

Planet

Planet IAP-2000PS Bedienungsanleitung

Planet

Planet WDAP-850AC Bedienungsanleitung

Planet

Planet WNAP-6305 Bedienungsanleitung

Planet

Planet RTL8812AU-CG Bedienungsanleitung

Planet

Planet WDAP-1750AC Bedienungsanleitung

Planet

Planet WNAP-6350 Bedienungsanleitung

Planet

Planet WNAP-3000PE Bedienungsanleitung

Planet

Planet Wireless Access Point w/Bridge WAP-1963A Bedienungsanleitung

Planet

Planet WAP-2000 Bedienungsanleitung

Planet

Planet WNAP-7320 Bedienungsanleitung

Planet

Planet WAP-4036 Bedienungsanleitung

Planet

Planet MAP-3100 Kurzanleitung

Planet

Planet WAP-1000 WireFree Bedienungsanleitung

Planet

Planet WAP-4033 Bedienungsanleitung

Planet

Planet WDAP-1750AC Bedienungsanleitung

Planet

Planet WAP-1966 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung