Planet WAP-4033 Bedienungsanleitung

54Mbps Wireless Access Point

WAP-4033

User’s Manual

be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or

computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,

manual or otherwise, without the prior written permission of PLANET.

PLANET makes no representations or warranties, either expressed or implied, with respect to the

contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular

purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove

defective following their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes

the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting

from any defect in the software. Further, PLANET reserves the right to revise this publication and to

make changes from time to time in the contents hereof without obligation to notify any person of such

revision or changes.

All brand and product names mentioned in this manual are trademarks and/or registered trademarks of

their respective holders.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

1.Reorient or relocate the receiving antenna.

2.Increase the separation between the equipment and receiver.

3.Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

4.Consult the dealer or an experienced radio technician for help.

FCC Caution

To assure continued compliance. (example-use only shielded interface cables when connecting to

computer or peripheral devices). Any changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two

conditions: ( 1 ) This device may not cause harmful interference, and ( 2 ) this Device must accept any

interference received, including interference that may cause undesired operation.

Federal Communication Commission (FCC) Radiation Exposure

Statement

This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In

order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to

the antenna shall not be less than 20 cm (8 inches) during normal operation.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN

PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication

terminal Equipment and the mutual recognition of their conformity (R&TTE)

The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal

Equipment and Satellite Earth Station Equipment) As ofApril 8,2000.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it. However,

special attention must be paid to the dangers of electric shock and static electricity when working with

electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed

at all times to ensure the safe use of the equipment.

EU Countries Not Intended for Use

The ETSI version of this device is intended for home and office use in Austria Belgium, Denmark,

Finland, France (with Frequency channel restrictions). Germany, Greece, Ireland, Italy,

Luxembourg .The Netherlands, Portugal, Spain, Sweden and United Kingdom.

The ETSI version of this device is also authorized for use in EFTA member states Iceland,

Liechtenstein, Norway and Switzerland.

Potential Restrictive Use

France: Only channels 10,11,12 and 13

WEEE Regulation

To avoid the potential effects on the environment and human health as a result of the

presence of hazardous substances in electrical and electronic equipment, end users of

electrical and electronic equipment should understand the meaning of the crossed-out

wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to

collect such WEEE separately.

Revision

User’s Manual for PLANET Wireless Access Point

Model: WAP-4033

Rev: 1.0 (August, 2005)

Part No. EM-WAP4033

TABLE OF CONTENTS

Chapter 1 Introduction ..................................................................................7

1.1 Package Contents.................................................................................................... 7

1.2 Features................................................................................................................... 7

1.3 LED Indicators.......................................................................................................... 8

1.4 Wireless Performance.............................................................................................. 8

1.5 Reset Button............................................................................................................. 9

Chapter 2 Hardware Installation.................................................................10

Chapter 3 Web Configuration .....................................................................11

3.1 Home.......................................................................................................................11

3.2 Basic Setting .......................................................................................................... 12

3.2.1 AP Mode.....................................................................................................................12

3.2.2 Station - Ad Hoc Mode................................................................................................14

3.2.3 Station - Infrastructure Mode......................................................................................15

3.2.4 AP Bridge - Point to Point Mode.................................................................................16

3.2.5 AP Bridge - Point to Multipoint Mode..........................................................................17

3.2.6 AP Bridge - WDS Mode..............................................................................................18

3.2.7 Universal Repeater Mode...........................................................................................20

3.2.8 Security setting of bridge mode..................................................................................22

3.3 Advanced Settings ................................................................................................. 24

3.4 Security .................................................................................................................. 25

3.4.1 802.1x.........................................................................................................................27

3.4.2 WEP...........................................................................................................................26

3.4.3 WPA pre-shared key...................................................................................................28

3.4.4 WPA RADIUS.............................................................................................................29

3.5 MAC Filtering.......................................................................................................... 30

3.6 System Utility.......................................................................................................... 31

3.7 Configuration Utility................................................................................................ 32

3.8 Upgrade.................................................................................................................. 33

3.9 Reset...................................................................................................................... 33

Chapter 4 Specification...............................................................................35

Chapter 5 Frequently Ask Question...........................................................36

Chapter 1 Introduction

Thank you for purchasing WAP-4033. The WAP-4033 supports both IEEE 802.11b and IEEE 802.11g

standards. You can use it to connect an existing WLAN, or to build up a new wireless LAN. Except for

essential AP mode, WAP-4033 also provides AP Client/ Bridge/ Repeater and WDS (Wireless Distributed

System) modes to accommodate all kinds of network topology. High data rate (up to 54Mbps) support

allows faster communication between LAN and WLAN. Maximize network efficiency while minimizing

your network investment and maintenance costs.

Supports WPA, WPA2, WEP and MAC address filter function to consolidate the wireless network security,

you can prevent unauthorized wireless stations from accessing your wireless network.

This product provides a friendly web interface and allows users to configuring from browser. Without

utility install, user doesn’t need to find the utility for this product in lots of program list; it can be configured

in different OS via web browser.

1.1 Package Contents

Make sure that you have the following items:

 1 x WAP-4033

 1 x Power Adapter

 1 x User’s Manual CD

 1 x Quick Installation Guide

 1 x External Antenna

Note: If any of the above items are missing, contact your supplier as soon as

possible.

1.2 Features

 Complies with the IEEE 802.11b/g (DSSS) 2.4GHz specification

 Data rate supports up to 54Mbps

 Auto rate fallback in case of obstacles or interferences

 Supports WEP/WPA-PSK/WPA/WPA2 encryption

 Supports AP/ AP Client/ Bridge/ Repeater and WDS (Wireless Distributed System) mode

 Seamlessly integrate wireless and wired networks

 Provides MAC Filter function

 Built-in DHCP server

 Web-based configuration

1.3 LED Indicators

LED Color Function

PWR Green Off: Power is not connected

On: Device is ready

Blink: During boot up procedure

WLAN Green Off: Wireless LAN is no function

Blink: Transmitting or receiving data through the Wireless LAN

LAN Green Off: LAN is not connected

On: LAN is connected

Blink: Transmitting or receiving data through the LAN

1.4 Wireless Performance

The following information will help you utilizing the wireless performance and operating coverage of

WAP-4033.

1. Site selection

To avoid interferences, please locate WAP-4033 and wireless client away from transformers,

microwave ovens, heavy-duty motors, fluorescent lights and other industrial equipments. Keep the

number of walls or ceilings between AP and clients as few as possible. Otherwise the signal strength

may be seriously reduced. Place WAP-4033 in an open space or add additional WAP-4033 as

needed to improve the coverage.

2. Environmental factors

The wireless network is easily affected by many environment factors. Every environment is unique

with different obstacles, construction materials, weather, etc. It is hard to determine the exact

operation rage of WAP-4033 in a specific location without testing.

3. Antenna adjustment

The bundle antenna of WAP-4033 is adjustable. Firstly install the antenna pointing straight up, then

smoothly adjust it if the radio signal strength is poor. But the signal reception is definitely weak in

some certain areas, such as location right down the antenna.

Moreover, the original antenna of WAP-4033 can be replaced with other external antennas to extend

the coverage. Please check the specification of the antenna you want to use, and make sure it can

be used on WAP-4033.

4. WLAN Type

If WAP-4033 is installed in an 802.11b and 802.11g mixed WLAN, its performance will reduced

significantly. Because every 802.11g OFDM packet needs to be preceded by an RTS-CTS or CTS

packet exchange that can be recognized by legacy 802.11b devices. This additional overhead

lowers the speed. If there are no 802.11b devices connected, or if connections to all 802.11b devices

are denied, the WAP-4033 can operate in 11g-only mode, and its data rate should actually 54Mbps.

1.5 Reset Button

WAP-4033 provides a Reset button on the rear panel for user to restart or set WAP-4033 configuration to

factory default.

Time Active

Press less than 5 Sec. WAP-4033 will re-boot itself, keeping your original configurations

Press more than 5 Sec. WAP-4033 will reset itself to the factory default settings

Chapter 2 Hardware Installation

Before you proceed with the installation, it is necessary that you have enough information about the

WAP-4033.

1. Locate an optimum location for the WAP-4033. The best place for your WAP-4033 is usually

at the center of your wireless network, with line of sight to all of your mobile stations.

2. Assemble the antenna to WAP-4033. Try to place them to a position that can best cover your

wireless network. The antenna’s position will enhance the receiving sensitivity.

3. Connect RJ-45 cable to WAP-4033. Connect this WAP-4033 to your LAN switch/hub or a single

PC.

4. Plug in power adapter and connect to power source. After power on, WAP-4033 will start to

work.

Note: ONLY use the power adapter supplied with the WAP-4033. Otherwise, the product may be

damaged. If you want to reset your WAP-4033 to default settings, press the Reset button 5

second. Then release the button and wait for 10 seconds for rebooting.

Andere Handbücher für WAP-4033

Inhaltsverzeichnis

Andere Planet Drahtloser Zugangspunkt Handbücher

Planet

Planet WDAP-C3000AX Bedienungsanleitung

Planet

Planet WAP-4035 Bedienungsanleitung

Planet

Planet WDAP-850AC Bedienungsanleitung

Planet

Planet WAP-4000A Bedienungsanleitung

Planet

Planet Wireless Access Point w/Bridge WAP-1963A Bedienungsanleitung

Planet

Planet WNAP-7300 Bedienungsanleitung

Planet

Planet WAP-900 Bedienungsanleitung

Planet

Planet WNAP-6305 Bedienungsanleitung

Planet

Planet IAP-2000PS Bedienungsanleitung

Planet

Planet WAP-4030 Bedienungsanleitung

Planet

Planet WNAP-1110 Bedienungsanleitung

Planet

Planet WNAP-6308 Bedienungsanleitung

Planet

Planet WNAP-7320 Bedienungsanleitung

Planet

Planet WNAP-7205 Bedienungsanleitung

Planet

Planet EPN-402NV Bedienungsanleitung

Planet

Planet WDAP-C1750 Bedienungsanleitung

Planet

Planet WAP-4030A Bedienungsanleitung

Planet

Planet Network Device WAP-5100 Bedienungsanleitung

Planet

Planet WDAP-W7200AC Bedienungsanleitung

Planet

Planet MAP-3100 Kurzanleitung

Planet

Planet WBS-202N Bedienungsanleitung

Planet

Planet WAPC-1232HP Bedienungsanleitung

Planet

Planet WAP-6100 Bedienungsanleitung

Planet

Planet WNAP-6325 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung