PNI ESCORT HP 6500 Bedienungsanleitung

1、Introduction

Thank you for your choose and buy the Nanfone CB Radio. In order

to make your CB Radio to use in the best condition, please read this

manual in detail.PNI Escort HP 6500 is a small, simple

operation and convenient vehicle CB Radio which has good

performance.

Feature：

Up/down keys on the microphone

Scan channel

LCD display

Auto ASQ/SQ adjustable

RF GAIN

External Speaker

2、Installation instructions

Check the materials before the installation, car charger is

connected to the car's 12 v power supply socket，the radio’s positive

and negative electrode connected to the car charger’s. Power

supply support 12 V to 13.8 V. Check all wiring are in good condition

before starting, ensure do not short circuit, ensure the radio can

boot running normally.

User Manual

3、Control panel function

Front view

Name

Short Press

Function

Long Press

Function

①

Microphone

socket

②

A/F

AM/FM Mode

Switch

Scan Function

③

LCD Display

④

Power On/Off

Volume

4、Operation

4.1 Power On/Off the radio

1. Turn VOL switch clockwise to power on the radio, the LCD

full screen display after spectrum model 1 s into the channel

state.

2. Turn the VOL Knob counterclockwise, until it clicks. The

radio is power off.

4.2 Volume Control

Turn clockwise to increase volume, turn counterclockwise to

decreases volume.

4.3 Channel Selection

1. Shortly press microphone【UP】or【DOWN】to change

working channel.

⑤

、

⑥

Channel

UP/DOWN

select

⑦

EMG(Emergen

cy Channel ）

9/19 Channel

Switch

⑧

RFG

Enter RF GAIN

Model

⑨

SQ/ASQ

Function Switch

Enter SQ (ASQ)

Level Switch

Switch To ASQ

Mode

2.Hold microphone 【UP】or【DOWN】to change working

channel fast.

4.4 Squelch level control

1.Shortly press【SQ】,until LCD shortly displays SQ and then

display X.X。X.X stands for the SQ level

0.F

SQ off

0.1

Lowest SQ level

…

2.8

Highest SQ level

2.Press microphone【UP】/【DOWN】shortly to change SQ

level.

3.Hold microphone【UP】/【DOWN】to change the SQ level

fast.

4.Hold【SQ】or wait for 3 seconds to store and exit.

4.5 ASQ control（9 level）

1. Hold【SQ】key，until LCD display AQ，the ASQ function

is turned on. The LCD will display A.X。X stands for the

ASQ level。

A.1

Lowest ASQ level

…

A.9

Highest ASQ level

2. Shortly press microphone【UP】/【DOWN】to change

ASQ level.

3. Hold microphone【UP】/【DOWN】to change ASQ level

fast.

4. Hold【SQ】or wait for 3 seconds to store and exit.

4.6 Modulation Type

Shortly press【A/F】key to switch between AM/FM mode

and the LCD displays the selected mode.

4.7 RF GAIN control

1.Shortly press【RFG】key，LCD displays R and the present

RF GAIN level flashes.

2.Shortly press microphone【UP】/【DOWN】to change the

level.

3.Shortly press【RFG】key to exit RF GAIN level control.

4.8 Emergency Channel

1.Shortly press【EMG】key to choose CH9，the channel

number flashes.

2.Shortly press 【EMG】key again to choose CH19，the

channel number flashes.

3. Shortly press【EMG】key third time to return to last normal

channel.

4.9 Key Lock

1.Hold【EMG】key for over 2 seconds to lock the keys, LCD

displays “LC”.

2.Hold【EMG】for over 2 seconds again to unlock the keys,

LCD displays “OF”.

4.10 Scan Function

1.Hold【A/F】to start scan function，LCD displays“SC”.

2.Press microphone【UP】/【DOWN】can choose scanning

clockwise or counterclockwise.

3.Press【A/F】or【PTT】key to exit scan function.

4.11 Changing the CB-Standard

1. Hold【A/F】while powering the radio on, until LCD

displays the norms.

2.Press microphone【UP】/【DOWN】to choose wanted

Norms.

3.Power off and power on again

Standard

Channels

Fequency Range

40FM/40AM

26.965-27.405MHZ

40 FM

26.965-27.405MHZ

40 FM

27.60125-27.99125MHZ

40FM/40AM

26.960-27.400MHZ

34FM/34AM

26.965-26.865MHZ

40FM/40AM

26.965-27.405MHZ

80FM

26.565-26.955MHZ

27FM/27AM

26.965-27.275MHZ

4.12 Restore factory default

1.Hold【SQ】key while powering the radio on, until the LCD

displays “rt”.

2. All channel and function setting will resume factory default

after above operation.

FCC Statement:This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.—Consult the dealer or an experienced radio/TV technician for help.This equipment complies with FCC radiation exposure limis set forth for an uncontrolled environment.This equipment should be instslles and operated with minimum distance 50cm between the radiator&your bady.

Andere Handbücher für ESCORT HP 6500

Inhaltsverzeichnis

Andere PNI Radio Handbücher