Polaris 7240 Sport Bedienungsanleitung

ENGLISH |FRANÇAIS |ESPAÑOL

H0582000_REVA

Owner's Manual

TYPE EP37--

7240 Sport

P724

WARNING

FOR YOUR SAFETY - For anything other than the routine cleaning and maintenance described in this manual, this product must be

serviced by a contractor who is licensed and qualified in pool equipment by the jurisdiction in which the product will be installed

where such state or local requirements exist. In the event no such state or local requirement exists, the maintainer must be a

professional with sufficient experience in pool equipment installation and maintenance so that all of the instructions in this manual

can be followed exactly. Improper installation and/or operation will void the warranty.

FCC Statement

This device complies with Part 15 of the FCC Rules and IC licence-exempt RSS standard. Operation is subject to

the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct

interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Any changes or modications not expressly approved by by the part responsible for compliance could void the user's

authority to operate the equipment.

NOTE: This device complies with FCC and IC RF radiation exposure limits set forth for general population. This device must be

installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in

conjunction with any other antenna or transmitter.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum

(or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users,

the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more

than that necessary for successful communication.

THANK YOU FOR PURCHASING THE POLARIS CLEANER.

YOUR POLARIS ROBOTIC CLEANER HAS BEEN DESIGNED AND MANUFACTURED TO BE EASILY

INSTALLED AND TO PROVIDE LOW MAINTENANCE OPERATION. PRIOR TO INSTALLING YOUR NEW

POLARIS CLEANER, PLEASE DO THE FOLLOWING:

1) Complete and return the warranty card.

2) Record your purchase information on the spaces provided below.

3) Attach your invoice (or a copy) to this page.

Taking these steps will help ensure prompt warranty service, should it be required. If service is required, please

contact your original dealer. If the original dealer does not perform warranty service, please visit

www.polarispool.com to locate an independent service company near you. If you are unable to locate a service

company, please call our Technical Support department at 1-800-822-7933.

RECORD YOUR POLARIS CLEANER DATA HERE:

Date of Purchase Purchased From Serial Number:

(located on robot- head)

City State/Province Zip/Postal Code

Table of Contents

1Important Safety Instructions ..................... 4

2 Cleaner Specications................................. 5

General Specications.................................................. 5

3Assembly ...................................................... 6

Contents ....................................................................... 6

Connect to a Power Source.......................................... 6

4General Cleaner Operation.......................... 8

Install and Submerge the Cleaner................................ 9

Start / Stop Cleaning .................................................. 10

Remove from the Pool.................................................11

Clean the Filter Canister............................................. 12

Store the Cleaner When Not in Use ........................... 14

5Maintenance ......14

Cord Tangling ............................................................. 14

Replacing Wear Parts................................................. 17

Replacing the Track.................................................... 18

Spare Parts................................................................. 19

6Troubleshooting20

Using the Information LED ......................................... 20

General Troubleshooting ............................................ 21

Page 4

English

WARNING

Failure to comply with the following warnings can result in permanent injury, electrocution or death.

PREVENT ELECTRICAL SHOCK

To reduce risk of electrical shock:

• Connect unit to receptacle protected by a ground fault circuit interrupter (GFCI). Such a GFCI

receptacle should be provided by a qualied installer and should be tested on a routine basis.

To test the GFCI, push the test button. The GFCI should interrupt power. Push the reset button.

Power should be restored. If the GFCI fails to operate in this manner, the GFCI is defective. If

the GFCI interrupts power to the pump without the test button being pushed, a ground current

is owing, indicating the possibility of an electric shock. Do not use this product. Disconnect the

cleaner and have the problem corrected by a qualied service representative before using.

• Per the United States National Electrical Code®(NEC®), keep the control unit at least ve (5) feet

from the edge of the (pool/spa) water. In Canada, the Canadian Electrical Code (CEC) requires

a minimum distance of 3m (10 ft.) to be maintained between the pool edge and the control unit.

Never submerge the control unit.

• Do not enter pool while the Polaris cleaner is in water.

• Do not bury cord. Locate cord so as to prevent it from being damaged by lawn mowers, hedge

trimmers and other equipment.

• To reduce the risk of electrical shock, do not use the Polaris robotic cleaner or control unit if the

cord is worn or damaged. Contact Zodiac Pool Systems, Inc. Technical Support immediately for

proper servicing and replacement of the damaged cord.

• Double insulation—For continued protection against possible electric shock, use only identical

replacement parts when servicing. Do not attempt repair of the Polaris robotic cleaner, control

unit, power cord, or oating cable.

• NEVER OPEN CONTROL UNIT.

• DO NOT USE AN EXTENSION CORD TO CONNECT THE UNIT TO ELECTRIC SUPPLY;

PROVIDE A PROPERLY LOCATED GFCI RECEPTACLE. THE CONTROL UNIT SHOULD BE

PLUGGED INTO THE GFCI RECEPTACLE BOX.

• PREVENT CHILD INJURY AND DROWNING

• To reduce the risk of injury, do not permit children to operate this product.

• Do not let anyone, especially small children, sit, step, lean, or climb on any equipment installed as

part of your pool’s operational system.

1Important Safety Instructions

Congratulations on purchasing the Polaris Robotic Cleaner. Please read through

the entire manual before installing your new robotic pool cleaner. Your cleaner must

be installed and operated as specied.

SAVE THESE INSTRUCTIONS

Page 5

English

CAUTION

• Failure to comply with the following warnings could cause damage to pool equipment or personal injury.

• The Polaris cleaner must be installed and operated as specied.

• This product is intended for use with permanently-installed pools. Do not use with storable pools. A

permanently-installed pool is constructed in or on the ground or in a building such that it cannot be

readily disassembled for storage. A storable pool is constructed so that it is capable of being readily

disassembled for storage and reassembled to its original integrity.

• Clean the lter canister in the Polaris cleaner after each use.

• Do not use the product in your pool if the water temperature is above 95˚ F (35˚ C) or below 55˚ F (13˚ C).

• USE OF THE POLARIS ROBOTIC CLEANER IN A VINYL LINER POOL

• Certain vinyl liner patterns are particularly susceptible to rapid surface wear of pattern removal caused

by objects coming into contact with the vinyl surface, including pool brushes, pool toys, oats, fountains,

chlorine dispensers, and automatic pool cleaners. Some vinyl liner patterns can be seriously scratched or

abraded simply by rubbing the surface with a pool brush. Ink from the pattern can also rub off during the

installation process or when it comes into contact with objects in the pool. Zodiac Pool Systems, Inc., is

not responsible for, and the Limited Warranty does not cover, pattern removal, abrasion or markings on

vinyl liners.

2 Cleaner Specications

General Specications

The general specications for the cleaner are as follows:

Control box

supply voltage

100-240 VAC, 50-60 Hz

Supply voltage 30 V DC

Installed load 100 W max

Cable length

54ft (16.5m)

Cleaner size

(WxDxH)

14.5 x 11.4 x 11.8 in. (

37 x 29 x 30 cm)

Weight of Cleaner 15.4 lbs. (7 kg)

Filtration

All-purpose lter canister

The cleaner is a double-insulated product. A double-insulated electrical appliance

is one which has been designed in such a way that it does not require a safety

connection to ground. The basic requirement for double-insulation is that no

single failure can result in dangerous voltage becoming exposed so that it might

cause an electric shock and that this is achieved without relying on an earthed

(grounded) metal casing. This is achieved by having two (2) layers of insulating

material surrounding live parts or by using reinforced insulation. Therefore,

devices having double-insulated construction, such as this cleaner, do not use a

grounded (three-prong) cord/plug.

Page 6

English

3Assembly

Contents

The packaging should contain the following items:

• Polaris robotic cleaner and  oating cable

• Control unit

• Control unit base

To protect the control unit from possible damage (which could lead to injury or property damage),

always secure the control unit to the control unit base during operation and storage.

When unpacking the cleaner and its components:

• Check to make sure each component is in the box.

• Check cleaner and components for damage during transport.

• If there are any missing parts or damage, contact Technical Support at

1-800-822-7933.

Connect to a Power Source

WARNING

• Failure to comply with the following warnings can result in permanent injury,

electrocution or drowning.

• Prevent Electrical Shock

• U.S.: Per NEC® requirements, keep the control unit at least  ve (5) ft. (1.5 m) from

the edge of the pool. CANADA: Per CEC requirements, keep the control unit at

least three (3) m (10 ft.) from the edge of the pool.

• Only connect the control unit to a receptacle protected by a ground fault circuit

interrupter (GFCI). Contact a certi ed electrician if you cannot verify that the

receptacle is protected by a GFCI.

• Do not use an extension cord to connect the control unit.

• Do not allow anyone to swim while the cleaner is in the pool.

• The control unit is water-resistant, not waterproof. In order to prevent electrocution,

never submerge the control unit or leave exposed to inclement weather.

Page 7

English

1. Seat the control unit rmly in the control unit base (Figure 1).

"CLICK"

Figure 1. Connect Control Unit Base

2. Unscrew the protective cap for the oating cable from the side of the

control unit by turning counter-clockwise (Figure 2).

Figure 2. Remove Protective Cap

3. Align the notch in the oating cable connector with the key in the control

unit, engage then turn clockwise to tighten (Figure 3).

Figure 3. Connect Floating Cable

Align:

Key with Notch

Page 8

English

4. Plug the control unit directly into a GFCI outlet. DO NOT use an extension

cord.

NOTE: To avoid damaging the power cable, do not try to twist

the entire cable housing (see below).

NOTE: To avoid exposing the power cable connector pins to water, be sure the connector is

screwed in all the way and there is no gap. (see below).

4General Cleaner Operation

CAUTION

To prevent damage to the cleaner, be sure to adhere to the following guidelines:

• Remove the cleaner from the pool after the cleaning cycle is completed.

• Store cleaner out of direct sunlight or inclement weather.

• Never lift the cleaner out of the pool by the oating cable.

• Take additional care when lifting the cleaner out of the pool. It becomes heavier when

lled with water.

• Always remove the cleaner from pool before super chlorinating or adding acid.

• Do not handle cleaner while it is in operation.

IMPORTANT

• Always make sure the cleaner head is fully submerged before you begin

operation.

• Clean the lter canister after each cleaning cycle.

• Do not leave your cleaner in the pool on a permanent basis.

• At the end of each cycle, remove the cleaner from the pool.

• Start at the cleaner head and untangle any coils in the cable before storing the

cleaner.

The Polaris robotic cleaner includes a safety feature that automatically stops the

cleaner if it is powered on but not submerged in water. For pools equipped with a

beach area, this safety feature is programmed to drive the cleaner in reverse and

back into the pool when the impeller is out of the water.

Page 9

English

Install and Submerge the Cleaner

1. With the control box plugged into a GFCI outlet, spread the  oating cable

across the pool deck until you reach the middle of the pool length.

2. Submerge cleaner vertically (1) and hold it under the surface, moving

gently from side to side (2) until the bubbles stop to remove any air trapped

inside (Figure 4).

3. When the bubbles stop, allow the cleaner to sink to the bottom of the pool.

4. Verify the cleaner is sitting on the bottom of the pool. Remove additional

air if the cleaner is still  oating.

Figure 4. Submerge and Remove Trapped Air

5. Place the cleaner in the pool at the recommended entry point (see Figure

4). Spread all of the  oating cable carefully in the pool, ensuring there

are no kinks or coils.

NOTE: For optimal patterning and reduced tangling, the floating cable should enter the

water near the middle of the pool length (see Figure 5).

Page 10

English

Figure 5. Pool Entry Point for Optimal Patterning

Control Unit

cleaner

Recommended

entry point

Not

Recommended

WARNING: Do not use

an extension cord

Start / Stop Cleaning

Press Start/Stop button to begin or interrupt cleaner operation (Figure 6).

Figure 6. Cleaner Control Unit

Start/Stop Cleaner

Operation

Information

LED

Andere Handbücher für 7240 Sport

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Polaris Schwimmbadroboter Handbücher

Polaris

Polaris Q4000 Bedienungsanleitung

Polaris

Polaris Vac-Sweep 360 Bedienungsanleitung

Polaris

Polaris robotic NEO EM27 Series Bedienungsanleitung

Polaris

Polaris Vac-Sweep 280 Bedienungsanleitung

Polaris

Polaris Vac-Sweep 280 Original Betriebsanleitung

Polaris

Polaris Vac-Sweep 380 Bedienungsanleitung

Polaris

Polaris Polaris 165 SuperTurtle Bedienungsanleitung

Polaris

Polaris SUPER TURTLE 165 Bedienungsanleitung

Polaris

Polaris 8050 Sport Bedienungsanleitung

Polaris

Polaris Vac-Sweep 480 PRO Bedienungsanleitung

Polaris

Polaris 65 TURBO TURTLE Bedienungsanleitung

Polaris

Polaris Vac-Sweep 180 Bedienungsanleitung

Polaris

Polaris iAquaLink CONTROL VTRX25iQ Bedienungsanleitung

Polaris

Polaris 3900 Sport Bedienungsanleitung

Polaris

Polaris 140 Bedienungsanleitung

Polaris

Polaris Vac-Sweep 280 Bedienungsanleitung

Polaris

Polaris Vac-Sweep 380 Bedienungsanleitung

Polaris

Polaris Vac-Sweep 480 PRO Bedienungsanleitung

Polaris

Polaris Spabot ES37 Series Bedienungsanleitung

Polaris

Polaris Maxx Bedienungsanleitung

Polaris

Polaris Vac-Sweep 360 Bedienungsanleitung

Polaris

Polaris Vac-Sweep 65 Bedienungsanleitung

Polaris

Polaris 165 SuperTurte Bedienungsanleitung

Polaris

Polaris Vac-Sweep 280 Bedienungsanleitung

Beliebte Schwimmbadroboter Handbücher anderer Marken

POOLGOODS

POOLGOODS PoolGobbler Pro Bedienungsanleitung

Maytronics

Maytronics Dolphin POOL UP Bedienungsanleitung

iRobot

iRobot Verro 600 Bedienungsanleitung

Kokido

Kokido SKOOBA K535CBX/18/EU Bedienungsanleitung

SmartPool

SmartPool Robo-Kleen PLUS Bedienungsanleitung

Brilix

Brilix BARACUDA Bedienungsanleitung

Aiper

Aiper Orca 1200 Pro Bedienungsanleitung

Hayward

Hayward Navigator Pro Bedienungsanleitung

Pentair

Pentair Prowler 710 Bedienungsanleitung

BWT

BWT D500 Bedienungsanleitung

Kokido

Kokido xtrovac 70 Bedienungsanleitung

Pentair

Pentair RACER Bedienungsanleitung

Pentair

Pentair REBEL 2 Bedienungsanleitung

Zodiac

Zodiac VX55 4WD Bedienungsanleitung

SmartPool

SmartPool Robo Kleen Plus Bedienungsanleitung

Steinbach

Steinbach Twin Bedienungsanleitung

STA-RITE

STA-RITE PoolShark Vacuum Bedienungsanleitung

Zodiac

Zodiac Baracuda G3 Bedienungsanleitung