Porter-Cable DA250A Bedienungsanleitung

FINISH NAILERInstruction

manual

The Model and Serial No. plate is located on the main

housing of the tool. Record these numbers in the

spaces below and retain for future reference.

Model No. ______________________________________

Type ___________________________________________

Serial No. _______________________________________

IMPORTANT

Please make certain that the person who is

to use this equipment carefully reads and

understands these instructions before

starting operations.

Part No. 903090 (016)

ESPAÑOL: PÁGINA 13

FRANÇAISE : PAGE 23

To learn more about Porter-Cable

visit our website at:

http://www.porter-cable.com

MODEL DA250A

903090 - 06-30-01.qxd 9/25/02 1:52 PM Page 1

Matthew G. Popik

Vice President of Engineering

PORTER

✦✦

CABLE

Porter-Cable Corporation

4825 Highway 45 North

Jackson, TN 38305

Date of Manufacture:___________________________

Fecha de fabricación:, Date de fabrication:

Serial No:______________________________________

Número de serie:, Nombre d'ordre

903090 - 06-30-01.qxd 9/25/02 1:52 PM Page 2

GENERAL SAFETY RULES

WARNING: When using pneumatic tools, basic safety precautions

should always be followed to reduce the risk of personal injury, including the

following:

READ AND FOLLOW ALL INSTRUCTIONS.

There are certain applications for which this tool was designed. Porter-Cable

strongly recommends that this tool NOT be modified and/or used for any

application other than for which it was designed. If you have any questions

relative to its application DO NOT use the tool until you have written Porter-

Cable and we have advised you.

Technical Service Manager

Porter-Cable Corporation

4825 Highway 45 North

Jackson, TN 38305

1. USE SAFETY GLASSES. To prevent

eye injuries, the tool operator and all

persons in the work area must wear safety

glasses with permanently attached, rigid,

plastic side shields. These safety glasses

must conform to ANSI Z87.1 requirements

(approved glasses have “Z87” printed or

stamped on them). Fig. 1.

2. WEAR EAR PROTECTION to safe-

guard against possible hearing loss. Fig. 1.

3. OPERATOR AND BYSTANDERS WEAR

HARD HAT to safeguard against possible

injuries. Fig. 1.

4. USE CLEAN, DRY, REGULATED com-

pressed air at 70 to 120 PSI, (4.8 to 8.3 BAR).

Fig. 2.

5. DO NOT CONNECT TOOL to pressure

which potentially exceeds 200 PSI (13.7

BAR).

6. ONLY USE AIR HOSE THAT IS RATED

for a maximum working pressure of at least

150 PSI (10.3 BAR) or 150% of the maximum

system pressure, which ever is greater.

7. NEVER USE OXYGEN, CARBON

DIOXIDE, combustible gases or any other

bottled gas as a power source for this tool:

explosion and serious personal injury could

result. Fig. 3.

8. CONNECT TOOL TO AIR SUPPLY

HOSE with a coupling that automatically

removes all pressure from the tool when the

coupling is disconnected. Fig. 4.

Fig. 1

Fig. 2

Fig. 3

Fig. 4

903090 - 06-30-01.qxd 9/25/02 1:52 PM Page 3

9. DISCONNECT TOOL FROM AIR

SUPPLY HOSE before doing tool

maintenance, clearing a jammed fastener,

leaving work area, moving tool to another

location, handing the tool to another person,

or making adjustments. Fig. 4.

10. NEVER USE A TOOL that is leaking air,

has missing or damaged parts, or requires

repair. Make sure all screws and caps are

securely tightened. Fig. 5.

11. NEVER USE TOOL IF SAFETY, trigger

or springs are inoperable, missing or

damaged. Do not alter or remove safety,

trigger, or springs. Make daily inspections for

free movement of trigger and safety

mechanism. Fig. 5.

12. DO NOT USE TOOL WITHOUT

SAFETY WARNING LABEL. If label is

missing, damaged or unreadable, contact

your Porter-Cable Service Center for a

replacement. Fig. 6.

13. ONLY USE PARTS, FASTENERS, AND

ACCESSORIES recommended by Porter-

Cable.

14. REMOVE ALL FASTENERS from tool

before connecting to air supply. The tool’s

driving mechanism may cycle when tool is

connected to the air supply. Fig. 7.

15. ALWAYS ASSUME THE TOOL

CONTAINS FASTENERS. Keep the tool

pointed away from yourself and others at all

times. No horseplay. Respect the tool as a

working implement. Fig. 8.

16. DO NOT LOAD FASTENERS with

trigger or safety depressed, to prevent

unintentional firing of a fastener. Fig. 9.

17. REMOVE FINGER FROM TRIGGER

when not driving fasteners. Never carry tool

with finger on trigger. Tool will fire a fastener

if safety is bumped while trigger is

depressed. Fig. 10.

18. DON’T OVERREACH. Keep proper

footing and balance at all times when using

or handling the tool.

Fig. 5

Fig. 6

Fig. 7

Fig. 8

Fig. 9

903090 - 06-30-01.qxd 9/25/02 1:52 PM Page 4

19. FIRE FASTENERS INTO WORK

SURFACE ONLY, never into materials too

hard to penetrate. Fig. 11.

20. GRIP TOOL FIRMLY TO MAINTAIN

CONTROL WHILE allowing tool to recoil

away from work surface as fastener is

driven. If safety element is allowed to

recontact work surface before trigger is

released an unwanted fastener will be fired.

21. DO NOT DRIVE FASTENERS on top of

other fasteners, or with the tool at too steep

an angle: the fasteners can ricochet causing

personal injury. Fig. 12.

22. DO NOT DRIVE FASTENERS CLOSE

to the edge of the workpiece. The workpiece

is likely to split allowing the fastener to fly

free or ricochet causing personal injury. Fig.

12.

23. KEEP HANDS AND BODY PARTS

away from area shown in Fig. 13A, to avoid

injury.

24. DO NOT USE ON SCAFFOLDINGS

OR LADDERS or for tasks in which

changing location involves the use of

scaffoldings, stairs, ladders, and the like. Do

not use for specific tasks such as closing

boxes or crates or fitting transportation

safety systems on vehicles and wagons.

Fig. 13B.

Fig. 10

TECHNICAL SPECIFICATIONS

Noise level . . . . . . . . . . . . . . . . . Typical Mean

A - Weighted sound impulse . . effective Acceleration . . .3.91 m/s2

power level . . . . . 95.1 dBA

P - Emission sound pressure

pressure level . . . 86.3 dBA

Fig. 11

Fig. 12

Fig. 13A

Fig. 13B

903090 - 06-30-01.qxd 9/25/02 1:53 PM Page 5

EMPLOYER’S RESPONSIBILITIES

WARNING: Employer must enforce compliance with the safety warnings

and all other instructions contained in this manual.

Keep this manual available for use by all people assigned to use this tool.

For personal safety and proper operation of this tool, read and follow all of

these instructions carefully.

OPERATING INSTRUCTIONS

FOREWORD

Porter-Cable Model DA250A is a heavy duty pneumatic finish nailer. It is

designed to install 15 ga. finish nails of various lengths (from 11/4" to 21/2" long),

see ACCESSORIES Listing in back of this manual.

CAUTION: Use approved Porter-Cable finish nails only (see

ACCESSORIES Listing in back of this manual).

POWER SOURCE

This tool is designed to operate on clean, dry, compressed air at regulated

pressures between 70 and 120 PSI (Pounds per Square Inch)

(4.8 to 8.3 BAR)

The preferred system would include a filter, a pressure regulator, and an

automatic oiler located as close to the tool as possible (within 15 ft/4.6 m is

ideal).

All compressed air contains moisture and other contaminates that are

detrimental to internal components of the tool. An air line filter will remove

most of these contaminates and significantly prolong the life of the tool. If an

in-line oiler is not available: place five or six drops of Porter-Cable Air Tool Oil

(see ACCESSORIES), into the tool’s air inlet at the beginning of each workday.

The tool is equipped with a

" male “quick connector”. A

" male “quick

connector” is available from Porter-Cable and may be used in situations where

" supply line is not available. A

" supply line (and fittings) are required for

maximum tool performance. The tool must always be connected to the air

supply with a coupling such that all pressure is removed from the tool when the

coupling is disconnected.

WARNING: All air line components (hoses, connectors, filters,

regulators, etc.) must have a minimum working pressure rating of at

least 150 PSI (10.3 BAR) or 150% of maximum system potential,

whichever is higher.

Do not connect this tool to a system with maximum potential

pressure greater than 200 PSI (13.7 BAR).

Only connect tool to air supply with a coupling that will automatically

release all pressure from the tool when disconnected.

Disconnect tool from air supply before performing maintenance,

clearing a jammed fastener, leaving work area, moving tool to another

location, or handing the tool to another person.

903090 - 06-30-01.qxd 9/25/02 1:53 PM Page 6

PREPARING THE TOOL

1. After reading and understanding this entire manual, connect tool to

air supply.

WARNING: Keep tool pointed away from yourself and others at all

times.

Always connect tool to air supply before loading fasteners.(see Fig.

14).

Do not load fasteners with trigger or safety depressed.

Only use approved Porter-Cable fasteners (see ACCESSORIES).

Always wear ANSI Z87.1 approved safety glasses, and hearing

protection when preparing or operating the tool.

Never use a tool that leaks air or needs repair.

2. Orient a strip of nails with points down (see Fig. 15), and align with the

magazine “T” slot.

3. Feed the strip of nails into the magazine

(“T” slot), until they are past the stop (A) Fig. 16.

4. Pull the follower (B) Fig. 17, all the way to

the rear of the magazine and release. The

follower will apply pressure to the strip of nails

to feed it into the driving mechanism.

5. Adjust directional exhaust deflector (A) Fig.

18, so that the exhaust air blast will be directed

away from the operator. The exhaust deflector

provides seven detented positions for directing

the exhaust blast away from the operator.

Grasp the deflector and rotate it to the desired

position for the current application.

Fig. 16 Fig. 17

←

Fig. 14 Fig. 15

←

Fig. 18

903090 - 06-30-01.qxd 9/25/02 1:53 PM Page 7

USING THE TOOL

Complete all steps of PREPARING THE TOOL before using the tool.

To fire, grip tool firmly, position nose of tool onto work surface, push forward

on tool to depress safety, and squeeze trigger to fire a fastener. This “trigger

fire” method provides the most accurate fastener placement. This tool is

shipped from the factory with a “restrictive fire trigger” that only allows the tool

to be fired this way and is less likely to fire an unwanted fastener.

An alternate “bottom fire trigger” is available. The “bottom fire” trigger allows

the tool to be fired in two different ways.

1. The tool can be fired using the “trigger fire” method described above.

2. Grip tool firmly, depress and hold trigger while pushing the tool firmly

against work surface. The tool will fire a fastener each time the safety is

depressed. This method is known as “bottom fire” and allows very fast

repetitive fastener placement.

The “bottom fire trigger” is available free-of-charge by calling 1-800-321-9443

in the United States and Canada or 001-731-660-9374 outside the United

States and Canada, and providing tool model and serial number. For

identification purposes: the Bottom Fire Trigger is black and the Restrictive Fire

Trigger is red.

WARNING: Remove finger from trigger when not driving fasteners.

Never carry tool with finger on trigger: tool will fire a fastener if safety

is bumped.

WARNING: Keep tool pointed in a safe direction at all times.

WARNING: Never attempt to drive a fastener into material that is too

hard, or at too steep an angle, or near the edge of the workpiece. The

fastener can ricochet causing personal injury.

WARNING: Disconnect tool from air supply before performing

maintenance, clearing a jammed fastener, leaving work area, moving

tool to another location, or handing the tool to another person.

WARNING: Clean and inspect tool daily. Carefully check for proper

operation of trigger and safety mechanism. Do Not use the tool unless

both the trigger and the safety mechanism are functional, or if the tool

is leaking air or needs any other repair.

The depth to which a fastener is driven is controlled by the depth adjustment

knob (A) Fig. 19. The depth of drive is factory adjusted to a nominal setting.

Test fire a fastener and check depth. If a change is desired, rotate the

adjustment knob (A) Fig. 19: the

adjustment knob has detents every 1/4

turn. Rotate the knob clockwise (see

Fig. 19), to increase the depth of

drive, rotate the knob counterclock-

wise to decrease the depth of drive.

Test fire another fastener and check

depth. Repeat as necessary to

achieve desired results. The amount

of air pressure required will vary

depending on the size of the fastener

and the material being fastened. Fig. 19

903090 - 06-30-01.qxd 9/25/02 1:53 PM Page 8

Experiment with the air pressure setting to determine the lowest setting that

will consistently perform the job at hand. Air pressure in excess of that

required can cause premature wear and/or damage to the tool.

A rubber nose cushion (A) Fig. 22, is provided to reduce marring of the work

surface. The rubber cushion can be pulled off to provide increased depth-of-

drive for toe-nailing applications.

WARNING: Disconnect tool from air supply before removing or re-

installing rubber cushion.

CLEARING A JAMMED FASTENER

1. WARNING: Disconnect tool from air supply.

2. Remove any remaining fasteners from the nailer.

A. Place finger through hole (A) Fig. 20, and push lever to release follower

mechanism.

B. Slide the follower to the left end of the magazine.

C. Depress the stop (B) Fig. 21, and slide all remaining fasteners out of the

magazine.

3. Open the quick release latch and hinge the fastener guide plate open (B)

Fig. 22.

4. Remove the jammed fastener (see Fig. 23).

5. Close the fastener guide plate and secure with the quick release latch.

Fig. 20 Fig. 21

Fig. 22 Fig. 23

←

903090 - 06-30-01.qxd 9/25/02 1:53 PM Page 9

MAINTENANCE

CLEAN AND INSPECT DAILY

WARNING: Disconnect tool from air supply before cleaning and

inspection. Correct all problems before placing the tool back in use.

Wipe tool clean and inspect for wear or damage. Use non-flammable cleaning

solutions to wipe exterior of tool only if necessary. DO NOT SOAK tool with

cleaning solutions. Such solutions can damage internal parts.

Inspect trigger and safety mechanism to assure system is complete and

functional: no loose or missing parts, no binding or sticking parts.

Keep all screws tight. Loose screws can cause personal injury or damage tool.

If tool is used without an in-line oiler: place 5 or 6 drops of Porter-Cable Air

Tool Oil into the air inlet of the tool at the beginning of each workday.

SERVICE AND REPAIRS

All quality tools will eventually require servicing or replacement of parts due to

wear from normal use. These operations should ONLY be performed by either

an AUTHORIZED PORTER-CABLE SERVICE STATION or a PORTER-

CABLE/DELTA FACTORY SERVICE CENTER. All repairs made by these

agencies are fully guaranteed against defective material and workmanship.

We cannot guarantee repairs made or attempted by anyone other than these

agencies.

Should you have any questions about your tool, feel free to write us at any

time. In any communications, please give all information shown on the

nameplate of your tool (model number, type, serial number, etc.).

TROUBLESHOOTING

WARNING: Disconnect tool from air supply before performing any

Service Procedure.

SYMPTOM PROBLEMS SOLUTIONS

1. Air leak near top of Loose screws. Tighten screws.

tool or in trigger area. Worn or damaged Install Overhaul Kit.

o-rings or seals.

2. Tool does nothing or Inadequate air supply. Verify adequate air supply.

operates sluggishly. Inadequate lubrication. Put 5 or 6 drops of oil into air inlet.

Worn or damaged Install Overhaul Kit.

o-rings or seals.

3. Air leak near bottom Loose screws. Tighten screws.

of tool. Worn or damaged Install Overhaul Kit.

o-rings or bumper.

4. Tool jams frequently. Incorrect fasteners. Verify approved fasteners of

correct size.

Damaged fasteners. Replace w/undamaged fasteners.

Magazine or nose Tighten screws.

screws loose.

Magazine is dirty. Clean magazine.

Driver is worn or damaged. Install “DRIVER” Maintenance Kit.

5. Other. Contact a Porter-Cable

Service Facility.

903090 - 06-30-01.qxd 9/25/02 1:53 PM Page 10

Inhaltsverzeichnis

Andere Porter-Cable Nagelpistole Handbücher

Porter-Cable

Porter-Cable FN250B Bedienungsanleitung

Porter-Cable

Porter-Cable FC350B Bedienungsanleitung

Porter-Cable

Porter-Cable DA250B Bedienungsanleitung

Porter-Cable

Porter-Cable FCN200 Bedienungsanleitung

Porter-Cable

Porter-Cable DA250 Bedienungsanleitung

Porter-Cable

Porter-Cable RN175B Bedienungsanleitung

Porter-Cable

Porter-Cable 8604 Bedienungsanleitung

Porter-Cable

Porter-Cable DA250C Bedienungsanleitung

Porter-Cable

Porter-Cable BN200B Bedienungsanleitung

Porter-Cable

Porter-Cable FCP350 Bedienungsanleitung

Porter-Cable

Porter-Cable DA250C Bedienungsanleitung

Porter-Cable

Porter-Cable PIN138 Bedienungsanleitung

Porter-Cable

Porter-Cable FC350 Bedienungsanleitung

Porter-Cable

Porter-Cable FC350A Bedienungsanleitung

Porter-Cable

Porter-Cable PIN100 Bedienungsanleitung

Porter-Cable

Porter-Cable 893885-007 Bedienungsanleitung

Porter-Cable

Porter-Cable PCC790B Bedienungsanleitung

Porter-Cable

Porter-Cable CFN250 Bedienungsanleitung

Porter-Cable

Porter-Cable FN250 Bedienungsanleitung

Porter-Cable

Porter-Cable FRP350 Bedienungsanleitung

Porter-Cable

Porter-Cable BN200C Bedienungsanleitung

Porter-Cable

Porter-Cable FC350B-CA Bedienungsanleitung

Porter-Cable

Porter-Cable PIN138-CA Bedienungsanleitung

Porter-Cable

Porter-Cable PN650 Bedienungsanleitung

Beliebte Nagelpistole Handbücher anderer Marken

Performance Tool

Performance Tool M643 Bedienungsanleitung

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco Fusion Technology F-35XP Bedienungsanleitung

Grizzly

Grizzly G1847 Bedienungsanleitung

Ryobi

Ryobi R18N18G Bedienungsanleitung

Black & Decker

Black & Decker 492848-00 Bedienungsanleitung

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Bedienungsanleitung

Metabo HPT

Metabo HPT NR 3690DC Bedienungsanleitung

Surtek

Surtek CN650 Abmessungen und Installationsanleitung

Makita

Makita GF600 Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco AirFree 25 Bedienungsanleitung

Freeman

Freeman P50LSLW Bedienungsanleitung

Aicon PRO

Aicon PRO DAC4507 Bedienungsanleitung

DAJ

DAJ XR150A Bedienungsanleitung

Makita

Makita AN923 Bedienungsanleitung

Grizzly

Grizzly T20644 Bedienungsanleitung