Porter-Cable FM350A Bedienungsanleitung

CLIPPED HEAD

FRAMING NAILER

Instruction

manual

The Model and Serial No. plate is located on the main

housing of the tool. Record these numbers in the

spaces below and retain for future reference.

Model No. ______________________________________

Type ___________________________________________

Serial No. _______________________________________

IMPORTANT

Please make certain that the person who is

to use this equipment carefully reads and

understands these instructions before

starting operations.

Part No. 910426 - 05-30-03

ESPAÑOL: PÁGINA 15

FRANÇAISE : PAGE 27

To learn more about Porter-Cable

visit our website at:

http://www.porter-cable.com

MODEL FM350A

PORTER

✦✦

CABLE

Porter-Cable Corporation

4825 Highway 45 North

Jackson, TN 38305

Date of Manufacture:___________________________

Fecha de fabricación:, Date de fabrication:

Serial No:______________________________________

Número de serie:, Nombre d'ordre

ENGLISH

EC-DECLARATION OF

CONFORMITY

We declare under our sole

responsibility that this product is in

conformity with the regulations

EN292-2: section 3 of 1992

EN292-1: section 5 of 1992

EN1050: 1993

EN792 13: 2000

ESPANOL

DECLARACION DE

CONFORMIDAD ”CE”

Declaramos bajo nuestra sola

responsabilidad que est e producto está en

conformidad con las regulaciones

EN292-2: section 3 of 1992

EN292-1: section 5 of 1992

EN1050: 1993

EN792 13: 2000

FRANÇAISE

DÉCLARATION DE CONFORMITÉ CE

Nous declarons sous notre propre

responsabilite que ce produit est conforme

aux reglementations

EN292-2: section 3 of 1992

EN292-1: section 5 of 1992

EN1050: 1993

EN792 13: 2000

indicates an imminently hazardous situation which, if not avoided,

will result in death or serious injury.

indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

indicates a potentially hazardous situation which, if not avoided,

may result in minor or moderate injury.

used without the safety alert symbol indicates potentially

hazardous situation which, if not avoided, may result in property

damage.

This manual contains information that is important for you to know and under-

stand. This information relates to protecting YOUR SAFETY and PREVENTING

EQUIPMENT PROBLEMS. To help you recognize this information, we use the

symbols below. Please read the manual and pay attention to these sections.

SAFETY GUIDELINES / DEFINITIONS

SAVE THESE INSTRUCTIONS!

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS.

There are certain applications for which this tool was

designed. Porter-Cable strongly recommends that this tool NOT be modified

and/or used for any application other than for which it was designed. If you

have any questions relative to its application DO NOT use the tool until you

have written Porter-Cable and we have advised you.

Technical Service Manager

Porter-Cable Corporation

4825 Highway 45 North

Jackson, TN 38305

Improper operation or maintenance of this product could

result in serious injury and property damage. Read and understand all

warnings and operating instructions before using this tool. When using

pneumatic tools, basic safety precautions should always be followed to

reduce the risk of personal injury.

Fig. 6

Fig. 5

Fig. 2

Fig. 3

Fig. 4

1. Read and understand tool labels and

manual. Failure to follow warnings could

result in DEATH or SERIOUS INJURY. Fig. 1.

2.Operator and others in work area MUST

wear safety glasses with side shields.

These safety glasses must conform to ANSI

Z87.1 requirements (approved glasses have

“Z87” printed or stamped on them). Fig. 2.

3. Keep fingers AWAY from trigger when

not driving fasteners to avoid accidental

firing. Never carry tool with finger on

trigger. In "contact actuation mode", tool

will fire a fastener if tool is bumped.

4. Choice of triggering method is

important. Check manual for triggering

options. See “Using the Tool with

Selectable Triggering Options” section of

this manual.

5. Never point tool at yourself or others

in work area. Serious injury or death may

occur if the tool is activated. Fig. 3

6. Never use oxygen or other bottled

gasses. Explosion will occur. Never use

combustible gases or any other reactive

gas as a power source for this tool:

explosion and serious personal injury will

result. Fig. 4.

7. Wear ear protection to safe-guard

against possible hearing loss. Ear

protection equipment must conform to ANSI

S3.19 requirements. Fig. 5.

8. Use clean, dry, regulated, com-

pressed air at 70 to 120 PSI, (4.8 to 8.3

BAR). Fig. 6.

Fig. 1

GENERAL SAFETY RULES

9. Do not connect tool to pressure which

potentially exceeds 200 PSI (13.7 BAR).

10. All air line components (hoses,

connectors, filters, regulators, etc.) must

be rated for a maximum working pressure

of at least 150 PSI (10.3 BAR) or 150% of

the maximum system pressure, which ever

is greater.

11. Connect tool to air supply hose with a

coupling that automatically removes all

pressure from the tool when the coupling is

disconnected. Fig. 7.

12. Disconnect tool from air supply hose

before doing tool maintenance, clearing a

jammed fastener, leaving work area, moving

tool to another location, or handing the tool

to another person. Fig. 7.

13. Never use a tool that is leaking air, has

missing or damaged parts, or requires

repair. Make sure all screws and caps are

securely tightened. Fig. 8.

14. Never use tool if safety, trigger or

springs are inoperable, missing or

damaged. Do not alter or remove safety,

trigger, or springs. Make daily inspections

for free movement of trigger and safety

mechanism. Fig. 8.

15. Do not use tool without safety

warning label. If label is missing, damaged

or unreadable, contact your Porter-Cable

Service Center for a replacement. Fig. 9.

16. Only use parts, fasteners and

accessories approved by Porter-Cable.

17. Connect tool to air supply before

loading fasteners, to prevent a fastener

from being fired during connection. The tool

driving mechanism may cycle when tool is

connected to the air supply. Fig. 10.

18. Always assume the tool contains

fasteners. No horseplay. Respect the tool

as a working implement. Fig. 11.

19. Operator and bystanders should wear

hard hats to safeguard against possible

injuries. Fig. 12.

20. Do not load fasteners with trigger or

safety depressed, to prevent unintentional

firing of a fastener. Fig. 13

Fig. 8

Fig. 9

Fig. 10

Fig. 7

Fig. 11

Fig. 12

Fig. 13

21. Remove finger from trigger when not

driving fasteners. Never carry tool with finger

on trigger. In “Contact Actuation Mode” tool

will fire a fastener if safety is bumped while

trigger is depressed. Fig. 14.

22. Do not overreach. Keep proper footing

and balance at all times when using or

handling the tool.

23. Fire fasteners into work surface only:

never into materials too hard to penetrate.

Fig. 15.

24. Grip tool firmly to maintain control

while allowing tool to recoil away from

work surface as fastener is driven. In

“Contact Actuation Mode” if safety element

is allowed to recontact work surface before

trigger is released an unwanted fastener will

be fired.

25. Do not drive fasteners on top of other

fasteners, or with the tool at too steep an

angle: the fasteners can ricochet causing

personal injury. Fig. 15.

26. Do not drive fasteners close to the

edge of the workpiece. The workpiece is

likely to split allowing the fastener to fly free

or ricochet causing personal injury. Fig. 16.

27. FOR TOOLS SET FOR CONTACT

ACTUATION MODE, Do not use on

scaffoldings or ladders or for tasks in

which changing location involves the use of

scaffoldings, stairs, ladders, and the like. Do

not use for specific tasks such as closing

boxes or crates or fitting transportation

safety systems on vehicles and wagons.

Fig. 17.

Fig. 14

Fig. 15

Fig. 16

Fig. 17

TECHNICAL SPECIFICATIONS

Noise level . . . . . . . . . . . . . . . . . . Typical Mean

A - Weighted sound impulse . . . effective Acceleration . . . . 4.2 m/s2

power level . . . . . . 105 dBA

P - Emission sound pressure

pressure level . . . . . . 98 dBA

Employer must enforce compliance with the safety warnings and all other

instructions contained in this manual.

Keep this manual available for use by all people assigned to use this tool.

For personal safety and proper operation of this tool, read and understand

tool labels and manual. Failure to follow warnings could result in DEATH or

SERIOUS INJURY. Read and follow all of these instructions carefully.

Porter-Cable Model FM350A is a heavy duty pneumatic framing nailer. It is

designed to install .113" to .131" diameter, wire collated clipped head,

framing nails of various lengths (2" to 31/2"). Fastener collation angle is 28°.

Use approved Porter-Cable fasteners only.

POWER SOURCE

This tool is designed to operate on clean, dry, compressed air at regulated

pressures between 70 and 120 PSI (Pounds per Square Inch)

(4.8 to 8.3 BAR)

The preferred system would include a filter, a pressure regulator, and an

automatic oiler located as close to the tool as possible, within 15 ft/4.6 m is

ideal.

All compressed air contains moisture and other contaminates that are

detrimental to internal components of the tool. An air line filter will remove

most of these contaminates and significantly prolong the life of the tool. If an

in-line oiler is not available: place five or six drops of Porter-Cable Air Tool Oil

into the tool’s air inlet at the beginning of each workday.

The tool is equipped with a 1

4" male “quick connector”. A 3

8" male “quick

connector” is available from Porter-Cable and may be used in situations where

a 1

4" supply line is not available. A 3

8" supply line (and fittings) are required for

maximum tool performance. The tool must always be connected to the air

supply with a coupling such that all pressure is removed from the tool when the

coupling is disconnected.

EMPLOYER’S RESPONSIBILITIES

FUNCTIONAL DESCRIPTION

PREPARING THE TOOL

1. After reading and understanding this entire manual, connect tool to

air supply (Fig. 18).

2. Orient a strip of approved fasteners with points down (A) Fig. 19, align,

and insert into the magazine “T” slot points first.

Do not load fastener strip into magazine backwards.

3. Observe fastener icon (A) Fig. 20. Insert fasteners (B) Fig. 20 with points

down (C) Fig. 20. Slide fasteners forward to the front of the magazine. The

magazine will hold two full strips of fasteners.

IMPORTANT: Fasteners must point in the same direction as they will be

driven.

4. Feed the strip of fasteners into the magazine (“T” slot), until they are past

the nail stop (A) Fig. 21.

5. Pull the follower (B) Fig. 21A, all the way to the rear of the magazine and

allow the follower (C) Fig. 21B to slide forward gently applying pressure to

the nail strips to feed the nails into the nail slot of the nose casting. Do not

allow the nail pusher to snap forward against the nail strips. This may

damage the nail collation and cause the nails to lodge in the nail slot of the

nose casting.

Fig. 19

Fig. 21A B

Fig. 20

Fig. 18

Fig. 21

←

Fig. 21B

←

6. Adjust directional exhaust

deflector (A) Fig. 22, so that the

exhaust air blast will be directed

away from the operator. The exhaust

deflector provides eight detented

positions for directing the exhaust

blast away from the operator. Grasp

the deflector and rotate it to the

desired position for the current

application.

USING THE TOOL WITH SELECTABLE TRIGGERING OPTIONS

Complete all steps of PREPARING THE TOOL before using the tool.

This tool is shipped from the factory with a selectable trigger set in the

“SINGLE SEQUENTIAL ACTUATION” firing mode as described in number

1 below. The selectable trigger can be set for the “CONTACT ACTUATION”

firing mode as described in number 2 below;

1. To use the tool in the SINGLE SEQUENTIAL ACTUATION MODE

depress trigger lever pivot pin (A) Fig. 23, rotate arrow to position (B), and

release. Note: Trigger lever pivot pin is spring loaded and held in position by

locking tab (D) Fig. 23 to prevent movement during operation. To fire, grip

tool firmly to maintain control, position nose of tool onto work surface, push

tool firmly against work surface to depress safety, as shown at (S) Fig.

24, and then squeeze trigger to fire a fastener. Allow tool to recoil away

from work surface as fastener is driven. This “single sequential

actuation” method provides the most accurate fastener placement.

-OR-

2. To use the tool in the CONTACT ACTUATION MODE depress trigger

lever pivot pin (A) Fig. 23, rotate arrow to position (C), and release. Note:

Trigger lever pivot pin is spring loaded and held in position by locking tab (D)

Fig. 23 to prevent movement during operation. To fire, grip tool firmly to

maintain control, squeeze and hold trigger, push tool firmly against work

surface to depress contact safety, as shown at (S) Fig. 24, and fire a

fastener.Allow tool to recoil away from work surface as fastener is

driven. If safety element is allowed to recontact work surface before trigger

is released an unwanted fastener will be fired. The tool will fire a fastener

each time the contact safety is depressed. This method is known as “contact

actuation” and allows very fast repetitive fastener placement.

IMPORTANT: A trigger, which will limit the tool to “single sequential

actuation” only, is available free-of-charge by calling 1-800-321-9443 in the

United States and Canada or 001-731-660-9374 outside the United States

and Canada, and providing tool model number, type, serial number, etc. For

identification purposes: the single sequential actuation trigger is red.

OPERATING INSTRUCTIONS

Fig. 22

Disconnect tool from air supply before performing

maintenance, clearing a jammed fastener, leaving work

area, moving tool to another location, or handing the tool

to another person.

Clean and inspect tool daily. Carefully check for proper

operation of trigger and safety mechanism. Do Not use the tool unless

both the trigger and the safety mechanism are functional, or if the tool is

leaking air or needs any other repair.

The depth to which a fastener is driven is controlled by the depth adjustment

knob (A) Fig. 25. The depth of drive is factory adjusted to a nominal setting.

Test fire a fastener and check depth. If a change is desired, rotate the

adjustment knob (A) Fig. 25. The adjustment knob has detents every 1/4turn.

Rotate the knob (A) Fig. 25 clockwise to increase the depth of drive, rotate

the knob counterclockwise to decrease the depth of drive. Test fire another

fastener and check depth. Repeat as necessary to achieve desired results.

The amount of air pressure required will vary depending on the size of the

fastener and the material being fastened. Experiment with the air pressure

setting to determine the lowest setting that will consistently perform the job

at hand. Air pressure in excess of that required can cause premature wear

and/or damage to the tool.

A rubber nose cushion (A) Fig. 26 is provided to reduce marring of the work

surface. The rubber cushion can be removed, and stored inside the bracket

(B) Fig. 27, to provide increased depth-of-drive for toe-nailing applications.

Disconnect tool from air supply before removing or

re-installing rubber cushion.

Fig. 25

Fig. 24

Fig. 23

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Porter-Cable Nagelpistole Handbücher

Porter-Cable

Porter-Cable PIN138-CA Bedienungsanleitung

Porter-Cable

Porter-Cable 883794-699 Bedienungsanleitung

Porter-Cable

Porter-Cable DA250C Bedienungsanleitung

Porter-Cable

Porter-Cable PCC790 Bedienungsanleitung

Porter-Cable

Porter-Cable DA250 Bedienungsanleitung

Porter-Cable

Porter-Cable BN200C Bedienungsanleitung

Porter-Cable

Porter-Cable CFN250 Bedienungsanleitung

Porter-Cable

Porter-Cable FR350A Bedienungsanleitung

Porter-Cable

Porter-Cable 8604 Bedienungsanleitung

Porter-Cable

Porter-Cable BN200B Bedienungsanleitung

Porter-Cable

Porter-Cable PIN138 Bedienungsanleitung

Porter-Cable

Porter-Cable FN250 Bedienungsanleitung

Porter-Cable

Porter-Cable FCN200 Bedienungsanleitung

Porter-Cable

Porter-Cable DA250B Bedienungsanleitung

Porter-Cable

Porter-Cable FC350 Bedienungsanleitung

Porter-Cable

Porter-Cable DA250C Bedienungsanleitung

Porter-Cable

Porter-Cable FN250A Bedienungsanleitung

Porter-Cable

Porter-Cable PCC790LA Bedienungsanleitung

Porter-Cable

Porter-Cable PN650 Bedienungsanleitung

Porter-Cable

Porter-Cable FN250B Bedienungsanleitung

Porter-Cable

Porter-Cable FR350 Bedienungsanleitung

Porter-Cable

Porter-Cable DA250B Bedienungsanleitung

Porter-Cable

Porter-Cable FCP350 Bedienungsanleitung

Porter-Cable

Porter-Cable FN250B Bedienungsanleitung

Beliebte Nagelpistole Handbücher anderer Marken

Performance Tool

Performance Tool M643 Bedienungsanleitung

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco Fusion Technology F-35XP Bedienungsanleitung

Grizzly

Grizzly G1847 Bedienungsanleitung

Ryobi

Ryobi R18N18G Bedienungsanleitung

Black & Decker

Black & Decker 492848-00 Bedienungsanleitung

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Bedienungsanleitung

Metabo HPT

Metabo HPT NR 3690DC Bedienungsanleitung

Surtek

Surtek CN650 Abmessungen und Installationsanleitung

Makita

Makita GF600 Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco AirFree 25 Bedienungsanleitung

Freeman

Freeman P50LSLW Bedienungsanleitung

Aicon PRO

Aicon PRO DAC4507 Bedienungsanleitung

DAJ

DAJ XR150A Bedienungsanleitung

Makita

Makita AN923 Bedienungsanleitung

Grizzly

Grizzly T20644 Bedienungsanleitung