POSIFLEX XP-3000 Series Bedienungsanleitung

FCC Notes:

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions manual, may cause interference to radio communications.

It has been tested and found to comply with limits for a Class A digital device pursuant to subpart

J of Part 15 of FCC Rules, which are designed to provide reasonable protection against

interference when operated in a commercial environment. Operation of this equipment in a

residential area is likely to cause interference in which case the user at his owns expense will be

required to take whatever measures to correct the interference.

Warranty Limits:

Warranty terminates automatically when any person other than the authorized technicians opens

the machine. The user should consult his/her dealer for the problem happened. Warranty voids if

the user does not follow the instructions in application of this merchandise. The manufacturer is by

no means responsible for any damage or hazard caused by improper application.

About This Manual:

Posiflex has made every effort for the accuracy of the content in this manual. However, Posiflex

Technology, Inc. will assume no liability for any technical inaccuracies or editorial or other errors

or omissions contained herein, nor for direct, indirect, incidental, consequential or otherwise

damages, including without limitation loss of data or profits, resulting from the furnishing,

performance, or use of this material.

This information is provided “as is” and Posiflex Technology, Inc. expressly disclaims any

warranties, expressed, implied or statutory, including without limitation implied warranties of

merchantability or fitness for particular purpose, good title and against infringement.

The information in this manual contains only essential hardware concerns for general user and is

subject to change without notice. Posiflex Technology, Inc. reserves the right to alter product

designs, layouts or drivers without notification. The system integrator shall provide applicative

notices and arrangement for special options utilizing this product. The user may find the most up

to date information of the hardware from: http://www.posiflex.com or http://www.posiflex.com.tw

or http://www.posiflexusa.com

All data should be backed-up prior to the installation of any drive unit or storage peripheral.

Posiflex will not be responsible for any loss of data resulting from the use, disuse or misuse of this

or any other Posiflex product.

All rights are strictly reserved. No part of this documentation may be reproduced, stored in a

retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying,

or otherwise, without prior express written consent from Posiflex Technology, Inc. the publisher of

this documentation.

©Copyright Posiflex Technology, Inc. 2010

All brand and product names and trademarks are the property of their respective holders.

XP-3000/3300 Series

Fan Free Touch Terminal

User’s Manual

Rev.: B0

154

09000

Page 1

ALERT TO OUR HONORABLE CUSTOMERS:

Please always read thoroughly all the instructions and documents delivered

with the product before you do anything about it. Don’t take any premature

action before you have a full understanding of the consequences.

DAILY MAINTENANCE GUIDE

For regular cleaning of the XP systems, please use only soft haired brush or

dry soft cloth. You may use moist soft cloth to remove stains when necessary.

Apply only suitable amount of mild neutral cleaner for obstinate stains. Please

note that never use Acryl dissolving solvent or Polycarbonate dissolving

solvent. You may apply ammonia-based glass cleaner only on the screen

surface.

ABOUT THIS PRODUCT

Posiflex XP-3000/3300 series presents a whole new generation POS terminal,

which is a combination of touch screen, printer, MSR, and the most reliable

FanFree system. This integrated solution of XP-3000/3300 series not only less

cable connection, but also carrying a brilliant performance to user in order to

face the busiest situation.

XP-3000/3300 Series applies Intel Pine View CPU technology; fast speed

Ethernet as well as plenty of connects ports of USB, Serial, VGA and CR ports.

It also integrated with thermal printer, touch screen and MSR, as well as

designed with gorgeous appearance and small footprint for counter space

saving. The small and fully integrated system is suitable for many kinds of

segments, such as general retailer, hospitality and restaurant. In addition, XP-

3000/3300 series terminal assist small and medium business to serve customer

effectively, speedy and precise.

All-in-one integrated system including touch screen, thermal printer and

MSR which is the best choice of POS system with limited space.

Integrated thermal printer with paper jams easy to fix design.

One touch power ON/OFF design provides convenience control for

terminal and printer.

The most reliable Fanfree structure for harsh environment.

Support Win POSReady, Win7 and Linux environment

Vertical type LCD panel with easy tilt angle adjustment

Supports SSD (Solid-State Drive) Data Storage Device or HDD

UPS function protects the system from intermittent power failure

External power support for COM 2/3 and VGA ports.

Page 2

INTRODUCTION

PRODUCT PICTURES

Front Views

Side Views

Rear & Bottom Views

Page 3

PARTS IDENTIFICATION

1. LCD display with touch panel

2. Printed paper exit

3. LED indicator for power and printer status

4. Paper feed button

5. Power switch

6. Brightness control buttons

7. Magnetic Stripe Reader(Option)

8. LCD adjustable Holder

9. Lock/Release button for tilt angle adjust

10. Printer cover

11. Printer cover release button

12. Three screw holes in back cover for customer pole display

integration

13. Cable Exit

14. Bottom plate compression lock

15. Bottom plate tenon

16. Rubber foot with bottom plate fixing screw

17. Bottom plate

PRODUCT FEATURES

Standard Features:

Models

Item XP-3012H

XP-3015H

XP-3312H

XP-3315H

LCD Display

(TFT LCD Panel)

Digital 12"

Digital 15"

Digital 12"

Digital 15"

CPU Intel Pine View D-SC 1.66G, 512K Cache

(Single core or Dual core)

VGA Port D-SUB 15Pin

DRAM Memory DDR2 667Mhz, Max 2GB (SO-DIMM X 1)

Serial Port 3, DB9 X 2, RJ-45 X 1 on the I/O Plate

CR Port X1, Control 2 cash drawers

Standard USB

Port

4 port on the I/O plate

Ethernet Port 10/100/1000 Mb

Touch Function USB Interface

Touch Sensor 5 Wire Touch Pad

Page 4

Storage device 2.5" SATA HDD or SSD HDD

Power switch On the top side

Power Saving Suspension mode

Indicator LED and

Control panel

switch

Power ON/ standby, bi-color LED, Printer Error (RED),

Paper Out (RED), paper feed / power ON switch /

Brightness

control buttons.

Fan-Free system Yes

OS support Windows XP Pro, WEPOS, POSReady, Win 7, Linux

Power Supply Power adaptor, 80W Power adaptor, 120W

Printer build in 3" Thermal Printer (60mm/sec)

3" Thermal Printer

(150mm /sec)

Printer auto cutter

Yes

Maximum Paper

roller diameter

80mm

Paper thickness

Less then 86µm

LCD panel tilt

angle 14~55 (degree)

Table: Summary of features

Models

Item XP-3012E XP-3015E XP-3312E XP-3315E

LCD Display

(TFT LCD Panel)

Digital 12"

Digital 15"

Digital 12"

Digital 15"

CPU Intel Pine View D-SC 1.8G , 512K Cache

(Single core or Dual core)

VGA Port D-SUB 15Pin

DRAM Memory DDR3 800Mhz, Max 4GB (SO-DIMM X 1)

Serial Port 3, DB9 X 2, RJ-45 X 1 on the I/O Plate

CR Port X1, Control 2 cash drawers

Standard USB

Port

4 port on the I/O plate

Ethernet Port 10/100/1000 Mb

Touch Function USB Interface

Touch Sensor 5 Wire Touch Pad

Storage device 2.5" SATA HDD or SSD HDD

Power switch On the top side

Power Saving Suspension mode

Page 5

Indicator LED and

Control panel

switch

Power ON/ standby, bi-color LED, Printer Error (RED),

Paper Out (RED), paper feed / power ON switch /

Brightness

control buttons.

Fan-Free system Yes

OS support Windows XP Pro, WEPOS, POSReady, Win 7, Linux

Power Supply Power adaptor, 80W Power adaptor, 120W

Printer build in 3" Thermal Printer (60mm/sec)

3" Thermal Printer

(150mm /sec)

Printer auto cutter

Yes

Maximum Paper

roller diameter

80mm

Paper thickness

Less then 86µm

LCD panel tilt

angle 14~55 (degree)

Table: Summary of features

Option Items:

Note: The underlined items in the following list means that option must be

set prior to shipment from the factory. The rest items can be set by the

dealers.

a) DDR2 SODIMM memory expansion up to 2GB max.

b) SATA SSD kit (SSD can’t coexist with SATA HDD in main unit).

c) Integrated upgrade kit:

2 or 3 track & JIS-II MSR

PD-309/309U, 2x20 LCD Customer display.

PD-330, 2x20 LCD Customer display.

PD-2605/2605U, 2x20 VFD Customer display.

PD-2606, 2x20 VFD Customer display.

PD-76X4 series, LCD 4x30 LCD pole display.

(PD-7614, PD-7624, PD-7634)

d) Integrated 2

display 12”(LM/TM-2212)

e) Preload OS Windows XP Pro, WEPOS, Win 7, POS Ready or Linux

f) Wireless LAN adaptor in USB interface

g) UPS Battery.

h) RJ-45 to DB9 connector cable for COM3.

Page 6

INSTALLATION GUIDES

Hardware Power Switch and printer paper feed

The power switch located in the front bezel of main unit. It

is a pushbutton switch and controls the power on/off of the

whole system. Also, next to the power and status indicators

is the paper feed button for integrated printer.

This power switch turns the system on when pushed only. This

switch turns the system off when pushed again during power

on status. However, if the system hangs due to any reason such

as software resource conflict, a simple push on the switch in 10

sec may turn off the power.

Note: There must always be at least 10 seconds waiting before switching

on again once the system is powered off successfully.

Brightness Control

In the front bezel of main unit and next to the power

switch, there are brightness adjust push button

switches. Each single press on the + or – button

changes the LCD panel display brightness by a small

amount. When you press and hold the button the

change will keep on until release or extreme condition matched.

Indicators of power and status

There is an indicator LED module serving for

several purposes at front bezel. The relationship

between the indicator status and other conditions is

summarized in following table:

Page 7

CAUTION: Before any installation or cable connection to the set, please

always make sure that the system is turned off and the

external power source to the set is removed to prevent electric

hazard! Never touch any metal pin in the connectors or

circuits to avoid high voltage hazard or electrostatic discharge

damage unless the operator is well grounded. Failure to do the

above will void the product warranty!

Display Issues

Main LCD Display

For best viewing result, please set your display resolution is 1024 x 768. The

system Video Memory is shared from system memory. XP-3000/3300 series

support DVMT Function and the video memory size is default in 128 MB and

can be set to be 64 MB.

VGA Port

The VGA port in the XP-3000/3300 system supports either a rear mount 2

display or a separately connected LCD monitor or touch monitor. To support

the DC power to the 2

display monitor, it required a qualified technician to

set up through BIOS setting. To supply the necessary power through the VGA

connector, please refer to the Posiflex technical information. Do not connect

other monitor to this port before the power in this port is disabled.

Posiflex USB Touch Manager

A program named “Posiflex USB Touch Manager” and a right-click sticky

button tool in the program group “Posiflex USB Touch Tools” is installed in

Indicator Terminal Status

LED colour

Standby Orange

Power Status Power On Blue

Printer Error Error Red

Printer Paper Out

Paper Out Red

Page 8

the preloaded Windows system with a USB interface touch panel controller.

This program can also be obtained by download from the POSIFLEX web site.

Mouse Emulation Touch Function

The touch panel in XP-3000/3300 system uses internal

USB interface as standard and occupies no external port.

When the touch driver is properly installed, this touch

panel works exactly like a standard mouse for each

interface. Nevertheless, if the system is running under

safe mode, the touch panel calibration may become

unsatisfactory due to disabled drivers. It is recommended to use a standard

USB mouse or keyboard in this mode.

All the mentioned mouse emulation functions can be manipulated through

relevant software. The system can give a beep and a click on the left button of

a mouse at the point when the touch panel is touched. If the point touched is

dragged across the screen surface, it works as the mouse drag and drop feature.

If the point is touched, released and touched within a short time interval, it is

double-clicking left button of the mouse. To obtain the effect like clicking on

the right button of a mouse, touching any point on the screen surface after

touching the right-click sticky button results as a click on the right button of

the mouse at that point.

Printer Operation

In the left side of XP-3000/3300 series’ main

unit, the printer with auto cutter is integrated

in XP-3012/3015/3312/3315.

For loading paper, please follow step A to E

sequentially with refer to pictures to use the

printer.

Step A: Please hold the LCD panel and push

lock/release lever for tilt angle adjust

forward. Turn the panel forward to

most vertical position (Note 1).

Step B: Push the printer cover release button.

Printer cover

release button

Paper Exit

Page 9

Step C: Pull up the printer cover.

Step D: Loading the paper roll and please notice that the paper roll’s

orientation should be face the printer head.

Step E: Please pull the paper longer then paper exit and close the printer cover

at the centre of front and please watch your finger during this step in

order to reduce hurt occur.

After finished steps A to E, the printer will cut the excess paper automatically

after the paper cover closed if the system power is turn on.

Note 1:

In order to protect the users’ fingers,

please notice that the push lock button in the

lock/release lever. When the LCD panel needs to be

push or pull from the most rear end, please press

the push lock and the lock/release lever at same

time then the LCD panel can pull or pull from the

rear end . Otherwise, the final level of tilt angel will be lock. The push lock

button only work when push or pull the final level of the LCD panel

adjustment.

Paper Near End Sensor

The near end sensor for

paper roll in the printer

is able to have the printer

work with paper rolls of

several bobbin sizes.

Please refer to the

picture at right for the

inside of the paper roll

compartment that there

are a plastic thumb

wheel for bobbin size

Sensor Position

Adjust

Support Roller

Sensor Block

Andere Handbücher für XP-3000 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere POSIFLEX Touch-Terminal Handbücher

POSIFLEX

POSIFLEX FT-6315 Bedienungsanleitung

POSIFLEX

POSIFLEX Jiva TP-8000 Bedienungsanleitung

POSIFLEX

POSIFLEX HT-4000 Series Bedienungsanleitung

POSIFLEX

POSIFLEX XT-5415 Bedienungsanleitung

POSIFLEX

POSIFLEX Jiva KS-6615 Series Bedienungsanleitung

POSIFLEX

POSIFLEX HT-2212 Pro Series Bedienungsanleitung

POSIFLEX

POSIFLEX Jiva LT 8015 Bedienungsanleitung

POSIFLEX

POSIFLEX XT-4015-G2 Bedienungsanleitung

POSIFLEX

POSIFLEX KS - 6815 Bedienungsanleitung

POSIFLEX

POSIFLEX Jiva KS-6215 Series Bedienungsanleitung

POSIFLEX

POSIFLEX MT-4210A Bedienungsanleitung

POSIFLEX

POSIFLEX XT-3615 Bedienungsanleitung

POSIFLEX

POSIFLEX XP-3000 Series Bedienungsanleitung

POSIFLEX

POSIFLEX XT-3815 Bedienungsanleitung

POSIFLEX

POSIFLEX PS-3415 Bedienungsanleitung

POSIFLEX

POSIFLEX HT-3200 SERIES Bedienungsanleitung

POSIFLEX

POSIFLEX DT-207 series Bedienungsanleitung

POSIFLEX

POSIFLEX TX-5600 Bedienungsanleitung

POSIFLEX

POSIFLEX MT-4310W/R Bedienungsanleitung

POSIFLEX

POSIFLEX KS7300 Series Bedienungsanleitung

POSIFLEX

POSIFLEX TX-3700 Series Bedienungsanleitung

POSIFLEX

POSIFLEX HS-3510W-E Bedienungsanleitung

POSIFLEX

POSIFLEX SA-304 Bedienungsanleitung

POSIFLEX

POSIFLEX Jiva 5815 Pro Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung