PowerWalker VFI 1000T/E LCD Bedienungsanleitung
EN
USER MANUAL
ONLINE UPS
PowerWalker VFI 1000T/E LCD
PowerWalker VFI 2000T/E LCD
PowerWalker VFI 3000T/E LCD
2
EN
Contents
1. Product introduction......................................................................... 2
1.1 Function description......................................................................1
1.2 Front panel....................................................................................2
1.3 Rear panel.....................................................................................5
1.4 Mode description...........................................................................7
1.5 Product specification...................................................................10
1.6 Communication port....................................................................12
2. Installation........................................................................................14
2.1 Safety Instructions for Installation...............................................14
2.2 Unpacking and Inspection...........................................................15
2.3 Installation steps for standard model..........................................16
2.4 Installation for communication software (optional) ..................... 16
3. Operation .........................................................................................18
3.1 Operation Safety Instructions......................................................18
3.2 Start the UPS with mains (AC source)........................................19
3.3 Start the UPS with battery (DC source) only ..............................20
3.4 Connect loads to UPS.................................................................21
3.5 Charge the batteries ...................................................................21
3.6 Discharge the batteries...............................................................22
3.7 Test the batteries.........................................................................22
3.8 Turn off the UPS with mains (AC source)...................................23
3.9 Turn off the UPS with battery (DC) only......................................23
4. Maintenance..................................................................................... 24
4.1 Maintenance Safety Instructions................................................. 24
4.2 Typical Troubleshooting ..............................................................26
4.3 Battery Maintenance...................................................................28
4.4 Contact the service centre..........................................................28
5. Transport and Storage....................................................................29
6. Standards.........................................................................................30
1
EN
1. Product introduction
1.1 Function description
This product is a true online double-conversion UPS
(Uninterruptible Power Supply). It provides perfect protection for
critical load such as computer system. It can eliminate almost all
mains power disturbances. The input AC current can be
corrected to a wave following the mains voltage, so it is a high
power factor system. Through the PWM control technology, the
output voltage can be a pure & stable sine waveAC voltage.
When the mains input become abnormal, the controller will stop
the AC/DC and start the DC/DC section immediately to make
sure the DC/AC (inverter) section can continue to work. After the
mains input come back to normal range, the DC/DC will be
stopped and the AC/DC works again. So the load is always
power-supplied through inverter without any interrupt if the UPS
is turned on.
The UPS also provides an internal bypass path so that the load
can be powered by mains input directly when the UPS is off or
failed.
The UPS is equipped with an internal charger for batteries which
charges the batteries when the mains are within a reasonable
range under “bypass mode” or “line mode”.
2
EN
1.2 Front panel
1.2.1 Front view
1K 2K/3K
3
EN
1.2.2 LCD and LED display
LED definition
There are total 4 LEDs to indicate the status of UPS.
Name
Colour
Function
Bypass LED
Orange
To indicate that the UPS is in bypass
mode, and the load current is directly from
the mains power.
Line LED
Green
To indicate that the mains input is normal.
Inverter LED
Green
To indicate that the load current is
supplied from the mains power or battery
via the inverter.
Battery LED
Orange
To indicate that the UPS is in battery
mode, and the load current is from battery
via the inverter.
4
EN
1.2.3 Button
(1) ON/OFF button
Turn on UPS
Press ON/OFF button for 1 second to turn on UPS.
UPS would send a beep to indicate the power-on
status
Turn off UPS
Press ON/OFF button for 1 second to turn off UPS
when UPS is in line mode or battery mode.
Clear fault status
Press ON/OFF button for 3 seconds to clear the fault
status of UPS.
(2) Test button
Battery test
In line mode, press test button for 2 seconds to test
the battery.
Mute in battery mode
Press test button for 2 seconds in battery mode,
UPS would be muted. To resume the alarm, press
test button again for 2 seconds.
Mute in all mode
Press test button for 10 seconds, UPS would be
muted. To resume the alarm, press test button again
for 10 seconds. The key tone and battery voltage
under alarm (every second buzzer beep twice)
cannot be muted.
Page up/down
Press test button for 0.5 seconds, UPS would turn
from main menu to sub-menu in sequence
5
EN
1.3 Rear panel
1K-IEC
1K-SCHUKO
1K-UK
2K-IEC
6
EN
1
Communication port (RS232)
5
Mains input protection
2
Intelligent card slot
6
Mains input power cord
3
Fan
7
Output terminal block
2K/3K-SCHUKO
2K/3K-UK
3K-IEC
7
EN
4
Output socket
1.4 Mode description
Line mode
Line mode means that the mains input is rectified/converted by the
AC/DC section and then inverted to stable output by DC/AC section.
In line mode, the output is well-regulated and good to the loads. If
the mains get abnormal, the UPS will transfer to battery mode
without interruption.
In line mode, Line LED and Inverter LED are turned on constantly.
1. If Line LED flashes, it means that the input may have something
wrong, such as input L and N line reversed or the grounding wire
is not connected properly.
2. If the load level is higher than 100%, the buzzer will beep one
every 0.5 second as a warning for the over-loading condition.
The user should remove unnecessary loads one by one, until the
load level become lower than 100%.
Line mode
8
EN
3. If the Battery LED flashes, it means that the battery is not
connected or the battery level is too low. In this case please
check the connection of battery and press test button for 2
seconds to test the battery. If the connection is normal, it’s
possible the battery is failed or aged. Please refer to the
common troubleshooting table in chapter 4.
Connecting AC Generator as Input
Remove the loads connected to UPS first. Activate the generator
and connect the output of generator with the input of UPS until the
generator operates stably, then turn on the UPS and add the loads
one by one.
Please choose the generator with output capacity which is twice
larger than the UPS capacity.
Battery mode
Battery mode means that the battery power goes through the DC/DC
section to the inverter (DC/AC) and output a stable backup power
when the mains are failed. If the mains recovered, the UPS will
transfer to line mode without interruption.
In battery mode, Battery LED and Inverter LED are turned on
constantly. If Line LED flashes at the same time, it means that the
input mains are abnormal.
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere PowerWalker UPS Handbücher
PowerWalker
PowerWalker VFI 10000CP 3/3 Bedienungsanleitung
PowerWalker
PowerWalker VI 650 SH Bedienungsanleitung
PowerWalker
PowerWalker VFI 1000 AT Bedienungsanleitung
PowerWalker
PowerWalker VFI 1000 R1U Bedienungsanleitung
PowerWalker
PowerWalker VFI 6000RT LCD Bedienungsanleitung
PowerWalker
PowerWalker VI RLP Series Bedienungsanleitung
PowerWalker
PowerWalker PowerMust 6054 Bedienungsanleitung
PowerWalker
PowerWalker VFI 6000 AT Bedienungsanleitung
PowerWalker
PowerWalker VI TW Series Bedienungsanleitung
PowerWalker
PowerWalker VFI 1000R LCD Bedienungsanleitung
PowerWalker
PowerWalker BP P96T Administratorhandbuch
PowerWalker
PowerWalker VFI 10000 CG PF1 Bedienungsanleitung
PowerWalker
PowerWalker VFI 3000T LCD Bedienungsanleitung
PowerWalker
PowerWalker VFI 160K CPG 3/3 BX Bedienungsanleitung
PowerWalker
PowerWalker VI 1000 Bedienungsanleitung
PowerWalker
PowerWalker VFI 1000RM LCD Bedienungsanleitung
PowerWalker
PowerWalker VI 400 SE Bedienungsanleitung
PowerWalker
PowerWalker VI 3000RT LCD Bedienungsanleitung
PowerWalker
PowerWalker VI 1000RT/LE Bedienungsanleitung
PowerWalker
PowerWalker 650 SH Bedienungsanleitung
Beliebte UPS Handbücher anderer Marken
Pylontech
Pylontech Victron & Pylontech US5000 Bedienungsanleitung
Tecnoware
Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung
Mecer
Mecer ME-1000-WTU Bedienungsanleitung
Mustek
Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch
Emerson
Emerson Liebert NXL series Bedienungsanleitung
MAKELSAN
MAKELSAN BOXER SERIES Bedienungsanleitung
