Powr-Flite PAS20BA-BC Bedienungsanleitung

OPERATOR’S MANUAL

WARNING: OPERATOR MUST READ AND UNDERSTAND THIS MANUAL

COMPLETELY BEFORE OPERATING THIS EQUIPMENT.

Save These Instructions

Automatic Scrubber

PAS20BA-BC

PAS20BA-BC-MAN 09/2018

TABLE OF CONTENTS

Safety Instructions .............................................................................3

Machine Set-Up..................................................................................4

Machine Specification........................................................................4

Replacement Parts:............................................................................8

Brush...............................................................................................8

Clutch Plate....................................................................................8

Battery............................................................................................8

Charger...........................................................................................8

Daily Operation and Maintenance.....................................................5

How to Install Batteries..................................................................5

How to Charge the Batteries.........................................................5

How to Install the Squeegee..........................................................5

How to Install Pad Holder and Brush............................................5

How to Fill the Solution Tank.........................................................5

How To Operate The Machine...........................................................6

How to Turn the Vacuum Motor On and Off..................................6

How to Lower/Raise the Brush/Pad..............................................6

How to Lower/Raise the Squeegee...............................................6

How to Set the Solution Flow........................................................6

What to Do When You’re Operating The Machine............................7

Vacuuming Up Solution..................................................................7

How to Control Excess Foam in the Recovery Tank ....................7

How to Empty the Recovery Tank.................................................7

Maintenance.......................................................................................7

Daily................................................................................................7

Weekly ............................................................................................7

Monthly...........................................................................................7

Troubleshooting..................................................................................8

Warranty..............................................................................................9

SAFETY INSTRUCTIONS

FOR COMMERCIAL USE

READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE

• Use indoors only. Do not expose to rain.

• Do not allow it to be used as a toy. Use caution when operating near children.

• Use only as described in this manual.

• Use only manufacturer’s recommended accessories.

• Charge batteries in a ventilated room. Gases given off during charging could ignite in a

confined space. To avoid an explosion, top cover should be open and battery caps installed

when charging.

• Disconnect all positive and negative battery terminals before attempting any adjustment

or maintenance. Brush drive and vacuum motors and components can cause injury if

accidentally started.

• Battery acid can cause injury to the eyes or skin. Wear protective goggles, gloves and clothing

BEFORE filling or charging batteries.

• If charger is not working properly, (due to it being dropped, damaged, left outdoors or exposed

to water) return it to a Powr-Flite Service Center.

• Do not handle the plug or machine with wet hands.

• Do not put any objects into openings. Keep the openings unblocked

• Keep it away from dust, lint, hair and anything that may reduce air flow.

• Keep hair, loose clothing, fingers and all body parts away from openings and moving parts.

• Make sure the main power switch is OFF before removing or installing pads or brushes.

• Never operate the machine if you are tired or under the influence of drugs and/or alcohol.

• Always operate the machine while standing behind it.

• Use care when working on electrical terminals. Short circuits can cause burns.

• Do not store the machine on inclines.

• If it is suspected that there is hazardous dust or flammable materials stop cleaning the area

immediately and consult your supervisor.

• Only use accessories and spare parts provided with the machine or those approved by the

manufacturer. The use of other accessories may impair the safety of the machine and void the

warranty.

Machine Specification

PAS20BA-BD Automatic Scrubber

Brush Width 20"

Squeegee Width 30"

Solution Tank 11 gal.

Recovery Tank 12 gal.

Brush Rotation 200 rpm

Productivity Rate 17,500 ft2per hour

Voltage 24 V

Vacuum Motor Power .75 HP/23A

Brush Motor Power .75 HP/23A

Weight (without Batteries) 210 lbs.

Length x Width x Height 49" x 26" x 44"

Machine Set-Up

19 20

b c de

789 101112

1. Handle Bar

2. Control Panel

a...Hour Meter

b...Battery Condition Indicator

c...Brush Motor Switch

d...Vacuum Motor Switch

e...Solution Switch

3. Squeegee Release Handle

4. Brush Lift Pedal

5. Wheel, Bump

6. Squeegee Mount Knob

7. Squeegee

8. Squeegee Tilt Knob

9. Water level sight tube

10. Battery

11. Valve, Solution Volume Control

12. Frame

13. Wheel

14. Brush/Pad Holder

15. Strap, Splash Guard

16. Solution Tank

17. Solution Fill Hole

18. Recovery Drain Hose

19. Recovery Tank

20. Squeegee Hose

21. Vacuum Hose

22. Key Switch

PART DESCRIPTION

Brush

SF219 Poly Scrub Brush (Optional)

PFLG19 Lite Grit Scrub Brush (Optional)

PFMG19 Medium Grit Scrub Brush (Optional)

PFHG16 Heavy Grit Scrub Brush (Optional)

Clutch Plate

UP2P Clutch Plate (must be used with all scrub brushes)

Pad Holder

PAS20PD 20” Pad Driver

Battery

B27TMX 12 Volt Battery (2 Required)

Charger

EC24 24 Volt, 20 Amp Charger

Replacement Parts

Daily Operation and Maintenance

How to Install Batteries

Caution: Batteries are heavy.

Install (2) 12-volt deep cycle batteries. New Batteries should be given a full charge before first use.

1. Unplug the hoses (20, 21) from the recovery tank (19).

2. Make sure the recovery tank is empty then lift it up.

3. Place batteries on the tray. Use the bracket to secure them. Position them correctly.

4. Connect all the cable terminals.

Caution: Make sure you connect RED (+) cable terminals to positive (+) posts and BLACK (-) cable terminals

to negative (-) posts. Machine will not operate if not connected properly. Failure to do so will result in

damage to batteries and possible explosion.

Spray each post with a protective lubricant. Place battery terminal protectors over all posts.

How to Charge the Batteries

Caution: Only use a battery charger designed for the machine. Failure to do so can result in damage to the

batteries.

Remove the recovery tank from machine and disconnect anderson plug from the control planel. Next connect the

charging plug to the anderson plug connected to the battery terminal. Plug the other charger plug to wall outlet. The

charger will automatically begin to charge the batteries.

How to Install the Squeegee

1. Put squeegee Release Handle (3) in the UP and locked position.

2. Position the squeegee blade assembly on the swing arm. Make sure the guide wheels face the rear of the

squeegee.

3. Hand tighten the 2 thumb screw (6).

4. Place the solution recovery hose (20) over the nozzle. Make sure it fits tight.

How to Install Pad Holder and Brush

1. Raise the brush pad by stepping on Brush Lift Pedal (4) at the rear of the machine.

2. With the pad holder/brush (14) in lifted position, insert it into the plate underneath by turning it counter-clockwise

until it locks.

How to Fill the Solution Tank

1. Open the solution fill cover (17).

2. Fill the tank (16) with the desired level of clean water.

3. Add cleaning chemical.

Do not overll.

1. To turn the power on, turn the key switch (22). The power/battery

indicator (b) will light up.

2. Check the battery capacity to see if it is full – all indicators are lit up

when batteries are fully charged.

3. To turn on the brush motor, vacuum motor and the solution flow, press

the switches (c,d,e).

Turn off the brush motor when the brush deck is in the up position.

How to Turn the Vacuum Motor On and Off

1. Push the top half of the right switch (d) down. This turns the vacuum

motor on.

2. To turn the vacuum motor off, push the lower half of the right switch

(d) down.

How to Lower/Raise the Brush/Pad

1. To raise the brush pad, step down on the Brush Lift Pedal (4) until it locks in place.

2. To lower the brush pad, slightly step on the Brush Lift Pedal (4) to unlock it, and

raise it up slowly.

How to Lower/Raise the Squeegee

1. Pull the handle (3) down to lower the squeegee.

2. Lift the handle (3) up to raise the squeegee.

How to Set the Solution Flow

Adjust the water flow based on the floor conditions. Turn the adjustment knob (11) to control the water flow.

Position 1 shows the closed position. Position 2 shows the maximum water flow position.

How To Operate The Machine

Vacuum Motor BrushMotor Water Flow

Vacuuming Up Solution

1. Make sure the squeegee is in the down position.

2. As the machine moves forward and solution is dispensed, the squeegee will vacuum it up into the recovery

tank.

3. If necessary adjust squeegee pressure by turning knob (8).

If solution is missed, reduce the amount of solution flow, raise the squeegee and pull the machine back over the

missed area. Lower the squeegee and move the machine forward to pick up any remaining solution.

How to Control Excess Foam in the Recovery Tank

Watch the liquid as it accumulates in the recovery tank. If you notice excess foaming, stop the machine. Add

the recommended amount of chemical defoamer in the recovery tank (19).

How to Empty the Recovery Tank

Open the Recovery Drain Hose (18) to empty the Recovery Tank (19).

Daily

1. Empty and rinse the recovery tank with clean water. Leave the tank cover (21) open on top to air dry.

2. Remove the squeegee assembly, rinse and wipe clean. Check the squeegee inlet for clogs or debris.

3. Clean and wipe the tops of batteries with an ammoniated window cleaner.

4. Fill each battery cell with DISTILLED water as needed. DO NOT use tap water.

5. Charge the batteries as described in this manual.

Weekly

Never test the strength of the battery unless it is fully charged and cool.

Check the battery cells with a hydrometer.

Monthly

1. Lubricate brush and squeegee lift mechanisms with light oil.

2. Check for wear or damage of clutch plate, brushes, pads or squeegee blades.

3. Clean all battery terminals.

4. Check all electrical connections and tighten if any are loose.

5. Clean the entire machine with all purpose cleaner.

What to Do When Operating The Machine

Maintennce

WARNING - Before performing maintenance or making adjustments, switch off the machine and disconnect the

battery.

* If the fuse blows several times, the machine should be checked by an authorised Service Agent

Troubleshooting

Problem: Possible Cause:

Solution is not being

picked up Vacuum motor is not running

Water filter is clogged

Recovery tank is full

Squeegee or vacuum hose is clogged, broken or disconnected

Bad seal at tank cover, vacuum motor or squeegee

Worn or misaligned squeegee blades.

Incorrect squeegee pressure.

Squeegee swing arm mechanism not functioning properly

Squeegee is leaving

streaks Debris is on blade

Blades are torn or damaged

Floors not properly swept before cleaning

Solution is not feeding or

turning off properly Clogging of hose or valve

Batteries are not

holding a charge Batteries need to be replaced

High current draw from high brush pressure

Charger needs servicing

Battery is run down

Floors are not being

scrubbed, stripped or

buffed properly

Brush motor not working

Excessive pad or brush wear

Going too fast over dirty spots

Inadequate solution feed

Inadequate cleaning procedure

A Tacony Company

3101 Wichita Court • Fort Worth, TX 76140-1755

1-800-880-2913 • Fax: 1-817-551-0719 • www.Powr-Flite.com

PAS20BA-BC-MAN 09/2018

Powr-Flite Warranty Statement

All Powr-Flite equipment has been tested and inspected at the factory and is guaranteed

to be free from defects in material and workmanship for the duration described below. For

full details, contact your authorized Powr-Flite Distributor, Service Center, or the Powr-Flite

Technical Service Department.

IMPORTANT WARRANTY CONDITIONS:

Warranty starts from the date of sale to the consumer or, at Powr-Flite’s discretion, six

months after the dealer has purchased the unit from Powr-Flite, whichever comes first.

All non-wear parts purchased after machine warranty expiration are warrantied for one

year. Proof of purchase is required to process all claims. Powr-Flite sales and service

representatives are not authorized to waive, alter, or increase the terms of this warranty.

Warranty DOES NOT cover the following:

• Routine wear and tear items such as brushes, filters, points, plugs, bulbs, switches,

brooms, wheels/tires, casters, fuses, belts, hoses, and sheer pins/motor couplings.

• Damage that occurs during shipping. A claim should be filed directly with the carrier to

collect damages.

• Unauthorized machine modifications or parts not purchased directly from Powr-Flite or an

authorized reseller.

• Failure to properly inspect, maintain, operate, and store the machine. Misuse/abuse is

determined at Powr-Flite’s sole discretion and examples include damage from pressure

washing the machine, exposing the machine to rain, cold, or snow, and damage to the

vacuum motor caused by failure to use defoamer.

• Cleaning and refinishing charges or machine downtime. Rentals and other replacement

machines are not available from Powr-Flite during the repair period.

2 Years - Motors

5 Years - Tanks

1 Year - Parts/Labor

Inhaltsverzeichnis

Andere Powr-Flite Bodenreinigungsmaschine Handbücher

Powr-Flite

Powr-Flite P1500-3 Installations- und Betriebshandbuch

Powr-Flite

Powr-Flite BlackMax B171 Bedienungsanleitung

Powr-Flite

Powr-Flite ORB1420 Bedienungsanleitung

Powr-Flite

Powr-Flite PAS14G Bedienungsanleitung

Powr-Flite

Powr-Flite PFX1080E Bedienungsanleitung

Powr-Flite

Powr-Flite NM2000 Bedienungsanleitung

Powr-Flite

Powr-Flite PAS26R Bedienungsanleitung

Powr-Flite

Powr-Flite MULTIWASH 14 Bedienungsanleitung

Powr-Flite

Powr-Flite CAS16 Bedienungsanleitung

Powr-Flite

Powr-Flite PFX3S Bedienungsanleitung

Powr-Flite

Powr-Flite PFX1080 SERIES Bedienungsanleitung

Powr-Flite

Powr-Flite Shine Brite 1200 RPM Bedienungsanleitung

Powr-Flite

Powr-Flite PEB Installations- und Betriebshandbuch

Powr-Flite

Powr-Flite 175 RPM 1 HP models Bedienungsanleitung

Powr-Flite

Powr-Flite C1600 Bedienungsanleitung

Powr-Flite

Powr-Flite PAS20B Bedienungsanleitung

Powr-Flite

Powr-Flite M201 Bedienungsanleitung

Powr-Flite

Powr-Flite NM171HD Bedienungsanleitung

Powr-Flite

Powr-Flite 98150-PF Bedienungsanleitung

Powr-Flite

Powr-Flite B171 Produkthandbuch

Powr-Flite

Powr-Flite M201-3 Bedienungsanleitung

Powr-Flite

Powr-Flite B2000 Bedienungsanleitung

Powr-Flite

Powr-Flite PFX900S Bedienungsanleitung

Powr-Flite

Powr-Flite M201-3 Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch