PR Lighting AQUA LED 730 FRAMING Bedienungsanleitung

AQUA LED 730 FRAMING

PR-8179

This product manual contains important information about the safe installation and use of this projector.

Pleaseread and follow theseinstructions carefullyandkeepthis manualin asafeplaceforfuture reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

INDEX

1. SAFETYANDWARNINGS. …………………………………………………………………………………

2. INSTRUCTIONS ……………………………………………………………………………………………

●CLEANINGANDMAINTENANCE ………………………………………………………………………

●LUBRICATION………………………………………………………………………………………………

●TROUBLESHOOTING ……………………………………………………………………………………

3.APPEARANCE…………………………………………………………………………………………………

4.INSTALLATION ………………………………………………………………………………………………

●RIGGING……………………………………………………………………………………………………

●POWERCONNECTIONS ………………………………………………………………………………

●DMXCONTROLCONNECTION…………………………………………………………………………

●DMXTERMINATOR………………………………………………………………………………………

●REPLACEMENTOFGOBOS ………………………………………………………………………………

5.SETUPANDCONFIGURATION………………………………………………………………………………

●FRONTPANELOPERATION………………………………………………………………………………

●DMXSTARTADDRESS……………………………………………………………………………………

●DMXWIRELESSCONTROL………………………………………………………………………………

●STAND-ALONEMODE ……………………………………………………………………………………

●MASTER/SLAVE MODE……………………………………………………………………………………

6.OPERATIONMENU …………………………………………………………………………………………

7.DMXPROTOCOL ……………………………………………………………………………………………

8.LOGOS ONTHESCREEN……………………………………………………………………………………

9. ERROR INFORMATION ……………………………………………………………………………………

10.TECHNICALDATA …………………………………………………………………………………………

11.CIRCUITDIAGRAMANDPCB CONNECTIONS……………………………………………………………

●CIRCUITDIAGRAM…………………………………………………………………………………………

●PCBCONNECTIONS…………………………………………………………………………………………

12.COMPONENTORDERCODES………………………………………………………………………………

The following items are suppliedwith the projector andplease check:

Name

Quantity

Unit

Remark

Gclamp

Pcs

XLRconnector

Set

Maleandfemale

Safetycord

Thismanual

Ω clamp

Pcs

Optional

Power Cord

Please note that as part of ourongoing commitment to continuous product development, specificationsare subject to change

without notice. Whilsteverycare istakeninthe preparationof the manual we reservetherightto change specificationsin the

course of productimprovement. The publishers cannot be held responsible for the accuracy of the information herein, or any

consequencearisingfromthem.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are

in good condition before installation anduse. Should there be any damage caused by transportation, consult your dealer and

donotusethe unit.Anydamagecausedby improperusewillnot be assumedbythe manufacturerand/ordealer.

Anyfuturetechnicalchangesarenotsubjecttofurthernotice.

Note: For the products made by Guangzhou PR lighting Ltd, the warranty for the whole product isone year starting from

thedelivery datebut the light sourceis notwithinthewarranty.

1. SAFETYANDWARNINGS

NOTE

Before a projector’s installation, power-on, operation and maintenance, please carefully read

the safety informationhereinafter!

Thefollowingsafetysignsareused intheusermanual.

Warning

User

Manual

Electrical

shock

Goggles

Protective

Gloves

Flames

High

Temperature

● When unpacking , check if there is transportation damage before using the projector. Should there be any

damagecausedbytransportation,consultyourdealeranddonotuse it.

●The manufacture isnotresponsible for loss caused bythe user not following the manual or changing the projector

ashe/shelikes

●Please be noted that thedamage caused bychangingtheprojectorat willis notwarranted.

● Do not hesitate to contact the dealer or the manufacturer if anyquestions or advice.

● Theprojector is forindoorandoutdoor use,IP65.

● Itcanbeusedinhumidanddustyareas.Anditcancontactwaterandother non-corrosiveliquids.

●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while

beingoperated

●The projector is only intended for installation, operation and maintenance by qualified personnel. And the

operationmuststrictlyfollowtheproceduresinthe manual

●Norepairablepartsintheprojectoranddonotopencovers for maintenancebyyourself.

●Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned.

●Donotconnect this deviceto any type ofdimmer pack

●After lamp switched on, the minimum distancebetweentheprojectorand illuminated surface is 5m

●If there are visible damages onthe lamp, lens and protective cover for the screen, i.e., to the extent whichaffects

itsperformancelikecrackingordeformation,pleasestopusingitandcontactthemanufacturefortheir

replacement withoriginalparts,otherwiseitsperformancewillbe compromised

●Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use a

projectorwhilecovers(housing)areoff

●Keepthelampcleanand do nottouch it withbare hands.

●While operating it,wearprotective items.

●Anyelectrical connectionmustbecarriedoutbya qualifiedperson.

●Before installation,please confirmthe voltage supplied matcheswhatisrequired forthe projector

●Eachprojector mustbe properlyearthedand installedasper relatedelectrical standards.

●Donotusepower cord withitsinsulatordamaged andconnectthepower cord withothercables.

●If the projector is not used or under cleaning,, please hold the plug and unplug it. Do not unplug it forcefully

orbypullingthepowercable.

●Allpower cordsmustconformto related safety andregulations

●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other

electrical parts’ life will be shortened .

●TheprojectorisofclassIP65,and notusedinthe environment higherthanit.

●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety

cord suppliedthroughthesafetycord holesforsafetysupport.

●Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from

power mains.

●After running for 5minutes, the temperature ofthe housing of the projector is45℃.After stable operation ,

itstemperature is80℃.

●While the lamp is stricken for the first time, there will be smoke and strange smell. It’s normal and does not

mean theprojector has some defects.

● Don’t touch the covers of the working projector(They are very hot!)

●Donotmounttheprojectordirectlyoninflammable surface.

●Do not project the beam straightly on combustible items and the minimum distance between the

projectorandilluminateditemsis5m.

●Aprojector should be installed with good ventilationand the minimum distance between the projector

andwallsis50cm.Atthe same time,pleaseensurethefans andairinletsandoutletsareworkable.

2. INSTRUCTIONS

●CLEANINGANDMAINTENANCE

If a projector can’t start. Please check if the fuse is blown up. If it does, replace it with a new fuse with same ratings. And the

projector has over-temperature protective device. Ifthe temperature is too high, the protective device will be triggered to shut the

projector off. When it happens, please check if the fans run normally or fan shield is blocked by dust. After the issue is solved,

restart theprojector.

The accumulation of oil, smoke and dust on the lens will compromise the light output. Cleaning a projector is very necessary to

ensure a reliable use of it. Cooling fans need to be cleaned every 15days.Internal lens, reflector and hot mirror need tobe cleaned

periodicallyto optimize light output.

The cleaning frequency of cooling fans and heatsink is decided by theoperations, environment and climate. It is advised to clean

itevery15daysorless. Userubberor bushorothernon-metallic tools to carry out cleaning. The tools can’t scratch or deformthe

heat sinkand fans.

Cleaning frequencyis to be decided by operations and itsenvironment. Use soft cloth and normal detergent forglass for cleaning

work. It’s advised external optical system be cleaned every 20days and internal optical systems every30/60days. Keep lens clean

and do nottouch opticalparts withbare hands.

Specialnote:

It’s normal phenomena that there will be mild water mist on the lens while the waterproof product is in use.

●Beforeanymaintenanceandcleaning,pleaseensuretheprojectisoffthepower

●Onlyqualifiedpersonisallowedtodo maintenance

●During maintenance andbefore maintenance, the projector mustbeoff power.

●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens

whether itrunsornot

●Donotusealcoholorotherorganicsolvent toclean the housingto avoiddamage.

●Donotuseanysolventwithchemical elementsto cleancolorfiltersorhotmirror.

●LUBRICATION

To ensure smooth movement of gobos and focus lens, it’s advised rotators’ bearings and 2 sliding bars for focus lens belubricated

every 2 months. High qualityand high temperaturelubricant/grease is advised..

●TROUBLESHOOTING

PROBLEM

ACTION

Theprojectorcan’t be switched on

Check ifthe fuse is burned

Check ifthe powercord is connected well

Check if the switching power supply is bad or not connected well. A

professionaltechnicianisrequired forthe repair

Check if the control board is connected well. .Aprofessional technician

isrequiredfortherepair

Theprojectorcanbeswitchedon,buttheLED

lamp’s brightness can’t be controlled

Check if the LED driver board is connected well. A professional

technicianisrequired for therepair

Theprojectorcanbeswitchedonnormally,but

notcontrolledbytheDMXcontroller

Make surethatthe fixture’s startaddressisright

Replaceorrepair theXLR signalcable.

Thebeamisnotbright anditsbrightness

decreasessharply

Makesurethefansareworkingwellorfansandtheirshieldsarenotblocked

bydust.

Makesurethattheinternalopticsisclean.

Beam appears dim, Lowin brightness

Make sure the lamp is within itslifespan

Removedustor greasefrom thelenses.

Theprojectimageappears tohaveahalo

CarefullycleantheLEDlamp,opticallensesand othercomponents.

HeavilyDefectiveBeam

Check if lensareingoodcondition(not cracked)

Cleandustor greaseonthelens.

3. APPEARANCE

4. INSTALLATION

●RIGGING

During transportation, please lock the projector well; Before the use of projector please unlock the head. It’s forbidden to run the

projector withoutunlockPanandTilt.

Body

Arm

Base

3PIN

DMX512

PIN FUNCTION

1 GND

2 DATA-

3 DATA+

DMX INDMX OUT

234

432

5PIN

DMX512

PIN FUNCTION

1 GND

2 DATA-

3 DATA+

4 N/C

5 N/C

DMX IN

DMX OUT

Take 2 clamps and 1 safety cords out from the package and mount 2 clamps on the underside of fixture with 4 retainers attached to

each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNINGon the underside of

the base as shown above) Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning.

Always ensure that the structure that youare going to mount the projector issecure and is strong enough to supportthe weight ofthe

fixture.

WARNING:

●TheprojectorMUSTbeliftedorcarriedbytheHANDLES insteadofclamps.

●.For safety the safety cord should afford 10 times the Projector’s weight.

●.Forsafety,it should notbe hungby itssides.

●POWERCONNECTIONS

Connect thepower cordas follows:

L(live)=brown

E(earth) =yellow/green

N(neutral)=blue

Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended thateach

projectorbeconnected withpower separatelyso thatthey maybeindividuallyswitched onandoff.

●The earth wire(yellow/green) must be connected to the ground. And electrical connection must be in

accordancewiththe standardsconcerned.

●Ifany questionsaboutthe electricalinstallation, donotcontinuebutconsultaqualifiedelectrician.

● The lighting fixture is with waterproof power socket, it should be equipped with same IPrating power

plug.

●DMXCONTROLCONNECTION

Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with

each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the

projector)or5 pinXLRplugs andsockets.The XLR'sareconnectedasshowninthefigureabove.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets

警告

请把保险绳穿过两个保

险绳扣板上以确保安全

保险绳扣板

保险绳

吊钩

提手

Warning

pleaserunthe safetycords through2 safety

cord holestoensuresafety

Safetycordholes

Clamp

Safetycord

Handle

图案盘1图案盘2

金属效果盘色片盘

mustn’t be connected in any way other than mentioned in the above figure. The projector accepts digital control signals in protocol

DMX512(1990).

Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second

fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX

terminatorasshowninthefigurebelow.

●DMXTERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electrical noise fromdisturbingandcorruptingtheDMXcontrol signals.

The DMX terminator is simply an XLR connector with a 120(ohm) resistor connected across pins 2 and 3, whichis then plugged

intothe output socket onthe lastprojector in the chain.The connectionsare illustrated below

●REPLACEMENTOFGOBOS

控制器

DMX512

回路插

输入输出输入输出输入

NO.1 NO.2 NO.n

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain. PIN 3

PIN 2

INPUT

DMXTERMINATOR

DMXCONTROLLER

OUTPUT

INPUT

OUTPUT

INPUT

Gobo wheel2

Gobo wheel1

Metallic effect wheel

Colorwheel

图案片安装滤色片安装

Locktiltand unfasten 4 screws of the small cover of the head. Open the cover and you’ll see the structure as above.

Replacement of the color filter. Pullout the color filter directlyby hand as the figure hereinafter in the sequence1→2. It’s installation

isinreverse sequenceastheremoval（2→1）.

Rotating gobos. Pull out the rotator as the figure hereinafter and the removal is in the sequence 1→2. Remove spring of the gobo

and take the gobo out. Place a new gobo in the rotator with the spring and ensure the spring is in the narrow groove of the

rotator ,i.e. its inner ring, then flatten it. At last use proper tool to push the tightening plate upward for the spring and use

another hand to help place the rotator in the original place. It is in the reverse sequence of the removal2→1.

Note: Do not touch color filters and glass gobos with bare hands. There should be clean and soft paper or cloth between hand and

glass.Install thechambercover, tighten4inner hexagonscrews and unlockTilt.

DANGER!

BEFORETHEREPLACEMENTOFGOBOANDCOLORFILTER,THEPROJECTORMUSTBEOFF

POWER.

5.SETUPANDCONFIGURATION

●FRONTPANELOPERATION

Projectorconfigurationcanbesetconvenientlyviapushbuttonandcolortouchscreen.

Launch the projector and pressbutton ENTER for more than 5 secondsto unlock the panel, the LCDwill show the function menu of

the projector, each main menu has its submenus and each submenu has a specific function. For details, please see the

“OPERATION MENU” section.

Pressbutton UP or DOWN ifyouwant tobrowsethroughthe variousSetupOptions.

Pressbutton ENTER to save yoursettingsorenterthesubmenu.

Pressbutton UP or DOWN tochangevalues(plusorminus)

Pressbutton FUNC,it willreturnto the upper menu.Ifbutton FUNC notpressed,thedefaultwill showdisplaystatusautomatically.

●DMXSTARTADDRESS

Eachprojector must be givena DMX start address so that the correct projector responds to the correct control signals. This DMX start

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the

controller. The projector has 3 DMX modes. Thereare short mode ,standard mode and extended mode. For example standard mode

DMX

W-DMX

ETHERNET

FUNC

DOWN

ENTER

Gobo Installation

ColorFilterInstallation

has 38 channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 039, No. 3 projector’s address 077, No. 4

projector’s address115,and so on.

Launch theprojector. Press button ENTER more than3secondsto unlock panel.

Pressbutton ENTER todisplayDMXaddress;

Pressbutton UP and DOWN,youcansettheaddress;

Pressbutton ENTER to confirm; afterpoweredon nexttime,the default willbelast value saved

Pressbutton FUNC, it willreturnto the uppermenu

●DMXWIRELESSCONTROL

Theprojector haswireless control functionwith wirelessreceiver moduleand antenna for remote control.

Thesetupofitisbelow:

1. Enter into the projector’s menu. Select the menu “Config Settigns” via the bottoms of UP and DOWN

2. Select DMX control Mode---- Wireless First (Note: Do not select XLR ONLY). The DMX wireless control

function is activated.

Only after the projector is linked with a transmitter, can it receive wireless signal sent by the transmitter. If unlinking it, Press

“Enter” for the menu of Unlink Wireless under the upper level menu of Config Settigns.

●STAND-ALONEMODE

Operate the projector without connecting with a controller, enable the master mode through the operation panel, the

projector will run in Stand-Alone mode automatically.

DMX address can be set at any number within 512.

●MASTER/SLAVEMODE

Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,

connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR controlcable and then connect the second

fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the

last fixture’s DMX output to a DMX terminator. Set 1st projector as the master and others are Slaves.

StartAddressesofallSlavesare001; Operationmodeof the Master can be set any mode for a Master’ and Slaves’ operation mode can

besetaccordingly.

AfterPoweredon,the group willruninMaster/Slave Mode

6. OPERATIONMENU

1st LEVEL

2ndLEVEL

3rdLEVEL

4thLEVEL

5thLEVEL

Address

DMXAddress

1-474

IP Address

DefaultIPAddress

2.X.X.X/10.X.X.X

CustomIPAddress

X.X.X.X

SubNetMask

X.X.X.X

ArtNet

ArtNetUniverse

0-255

Reset

Total Reset

Really Reset?

Confirm/Cancel

Pan&TiltReset

Really Reset?

Confirm/Cancel

ColourSystemReset

Really Reset?

Confirm/Cancel

GoboReset

Really Reset?

Confirm/Cancel

Zo.Fo.Fr.Pr.Reset

Really Reset?

Confirm/Cancel

OtherReset

Really Reset?

Confirm/Cancel

ConfigSettings

DMXChannelMode

ShortMode

Standard Mode

ExtendedMode

ViewSelected Mode

Strobe

…..

Signal Select

XLROnly

XLRFirst

WirelessOnly

WirelessFirst

WirelessIn/XLR Out

ArtnetOnly

ArtnetIn/XLR Out

LossofDMX

Normaltimeout

Hold LastValue

DisplayConfig

DisplayMode

OffAfterDelay

OnAlways

DisplayInvert

InvertOFF

InvertON

InvertAuto

LanguageSetting

English

Chinese

TemperatureUnit

CelsiusDegree

FahrenheitDegree

Un-LinkWireless

Really Un-Link?

Confirm/Cancel

Defaults

RestoreDefaults?

Confirm/Cancel

OptionSettings

Pan/Tilt Settings

PanDMXInvert

OFF/ON

TiltDMXInvert

OFF/ON

回路插

输入输出输入输出输入

主机从机从机

DMXTERMINATOR

MASTER

SLAVE

INPUT

OUTPUT

INPUT

OUTPUT

INPUT

DMXCONTROLER

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PR Lighting DJ-Equipment Handbücher

PR Lighting

PR Lighting XR440 BEAM Bedienungsanleitung

PR Lighting

PR Lighting StarBrite Bedienungsanleitung

PR Lighting

PR Lighting JUNIOR JNR-8146C Bedienungsanleitung

PR Lighting

PR Lighting Junior JNR Minifresnel 100MZ-W Bedienungsanleitung

PR Lighting

PR Lighting XR 1000 Framing Bedienungsanleitung

PR Lighting

PR Lighting LED STUDIO 3605 Bedienungsanleitung

PR Lighting

PR Lighting ARC LED 3108 Bedienungsanleitung

PR Lighting

PR Lighting AQUA 350 BEAM PR-2368 Bedienungsanleitung

PR Lighting

PR Lighting MEGA 4000 Bedienungsanleitung

PR Lighting

PR Lighting PR-8102 Bedienungsanleitung

PR Lighting

PR Lighting LED Studio 3300T Bedienungsanleitung

PR Lighting

PR Lighting XLED 6007 Bedienungsanleitung

PR Lighting

PR Lighting XPar 336-W Bedienungsanleitung

PR Lighting

PR Lighting JNR PAR COB Bedienungsanleitung

PR Lighting

PR Lighting ARC LED 1054 Bedienungsanleitung

PR Lighting

PR Lighting XR480 BWS Bedienungsanleitung

PR Lighting

PR Lighting XR-230 BEAM Bedienungsanleitung

PR Lighting

PR Lighting XL 1200 Bedienungsanleitung

PR Lighting

PR Lighting JNR-8119A Bedienungsanleitung

PR Lighting

PR Lighting LED Studio 3201D Bedienungsanleitung

PR Lighting

PR Lighting XR 1700 FRAMING Bedienungsanleitung

PR Lighting

PR Lighting XRLED 300 SPOT Bedienungsanleitung

PR Lighting

PR Lighting PR-8802 Bedienungsanleitung

PR Lighting

PR Lighting PR-2302 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung