PR Lighting XRLED 1200 SPOT Bedienungsanleitung

XRLED 1200 SPOT

PR-8180

This product manual contains important information about the safe installation and use of this

projector. Please read and follow these instructions carefully and keep this manual in a safe place

for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

2/22

INDEX

SAFE USAGE OF THE PROJECTOR 3

INSTALLING THE PROJECTOR 4

POWER SUPPLY – MAINS 5

CONTROL CONNECTIONS 5

DMX TERMINATOR 6

SETUP OPTIONS-PROJECTOR CONFIGURATION 6

TO SET THE DMX START ADDRESS 7

STAND-ALONE MODE 7

MASTER/SLAVE MODE 7

OPERATION MENU 8

REPLACING GOBOS 11

DMX PROTOCOL 12

INDICATION OF LED DISPLAY 14

MAINTENANCE 14

LUBRICATION 15

KEEPING THE PROJECTOR CLEAN 15

TROUBLESHOOTING 15

TECHNICAL DATA 16

ELECTRICAL DIAGRAM 19

COMPONENT ORDER CODES 20

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without

notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of

product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence

arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good

condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the

unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.

ACCESSORIES

These items are packed together with the projector:

Name Quantity Unit Remark

G clamps 2 Pcs

DMX connector 1 Set Without DMX cable

Safety cord 1 Pc

This manual 1 Pc

Ω clamps 2 Pcs Optional

3/22

SAFE USAGE OF THE PROJECTOR

When unpacking and before disposing of the carton check there is no transportation damage before using the projector.

Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.

The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture,

excessive heat, humidity and dust. Do not allow contact with water or any other liquids.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces. Be sure

that no ventilation slots are blocked.

Do not project the beam onto inflammable surfaces, minimum distance is 3m. 1.3m

Avoid direct exposure to the light from the lamp. The light is harmful to the eye.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.

Do not connect this device to any other types of dimmer apparatus.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact

with other cables. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.

The projector should always be installed with a secondary safety fixing. A safety cord is supplied for this; it should be

attached as shown in “installing the projector” section.

Shields and lens shall be changed if they have become visibly damaged to such an extent than their effectiveness is

impaired, for example by cracks or deep scratches.

Exterior surface temperatures of the luminaire after 5 minutes operation is 45℃, when steady state is achieved 50℃,

There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the

covers removed.

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

Always disconnect from the mains, when the device is not in use or before cleaning it or

before attempting any maintenance work!

4/22

INSTALL THE PROJECTOR

CLAMP

SAFETY CORD

HANDLE

CONTROL PANNEL

106

256

To pass SAFETY CORD

through 2 HOLES for safety!

WARNING

Take 2 clamps and the safety cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers

attached to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the

WARNING on the underside of the base as shown above) To pass SAFETY CORD through 2 HOLE for safety!

Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning. Always ensure that

the structure that you are going to mount the projector is secure and is strong enough to support a weight of each

projector.

WARNING:

1. A device MUST be lifted or carried by its HANDLES instead of clamps.

2. For safety the safety cord should afford 10 times the unit’s weight.

5/22

POWER SUPPLY-MAINS

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked

on the panel of the projector. It is recommended that each projector be supplied separately so that they may be

individually switched on and off.

IMPORTANT

It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant

standards.

CONTROL CONNECTION

Connection between controller and projector and between one projector and another must be made with a 2

core-screened cable, with each core having at least a 0.5mm diameter. Connection to and from the projector is via

cannon 5 pin (which are included with the projector) or XLR plugs and sockets. The XLR's are connected as shown in

the figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of

the plug is not connected in any way. The projector accepts digital control signals in protocol DMX512 (1990).

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input

and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown

in the figure below.

DMX OUT DMX OUTDMX IN TERMINATORDMX IN

NO.1 NO.2 NO.n

DMX IN FROM

CONTROLLER

6/22

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This

prevents electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120 (ohm) resistor connected across pins 2 and 3, which is

then plugged into the output socket on the last projector in the chain. The connections are illustrated below.

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

SETUP OPTIONS-PROJECTOR CONFIGURATION

W-DMXDMX

PR-8180

XRLED 1200 Spot

A device configuration can be set conveniently via pressbutton switch and LCD display.

Launch the projector. Press button ENTER more than 5 seconds to unlock panel, LED display shows functional menus

which have their own sub-menus for designated functions, the below is the details

Press button UP or DOWN if you want to browse through the various Setup Options.

Press button ENTER to save your settings or enter the next menu.

Press button UP or DOWN to shift.

Press button FUNC, it will return to the upper menu one by one. If you stay for minutes defaulted will show display status

automatically.

7/22

TO SET THE DMX START ADDRESS

Each projector must be given a DMX start address so that the correct projector responds to the correct control signals.

This DMX start address is the channel number from which the projector starts to “listen” to the digital control information

being sent out from the controller. The fixture has 3 DMX modes. There are standard mode, extended mode and short

mode. For example standard mode has 21 channels, so set the No. 1 projector’s address 001, No. 2 projector’s address

026, No. 3 projector’s address 051, No. 4 projector’s address 076, and so on.

Launch the projector. Press button ENTER more than 5 seconds to unlock panel.

Press either buttons of UP and DOWN under 1st level menu to locate the menu of DMX ADDRESS, press

ENTER to set DMX address.

Press button UP and DOWN, you can set the address;

Press button ENTER to confirm, after powered next time, the last saved settings will be showed.

Press button FUNC, it will return to the upper menu one by one.

STAND-ALONE MODE

Operate the projector without connecting a controller, enable the master mode in the operation panel, the

projector will run in Stand-Alone mode automatically.

DMX address can be set without limitations.

MASTER/SLAVE MODE

Many projectors can run synchronously in the Master/Slave mode by linking them with each other. Select

one projector as the master with setting options at any mode of master’s modes enabled and make the other

projectors as the slaves with setting options slave mode enabled and their DMX start address “001”.

Using XLR-XLR cables, Connect the first fixture’s output to the second fixture’s input, and connect the second fixture’s

output to the third fixture’s input and connect the rest fixtures in the same way. Eventually connect the last fixture’s output

to a DMX terminator as shown in the figure below.

After powered, the group will run in synchronous Master/Slave Mode.

DMX OUTDMX IN DMX OUTDMX IN TERMINATORDMX IN

MASTER SLAVE SLAVE

8/22

OPERATION MENU

1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL

DMX Address

Standard mode: 1~488

Extended mode: 1~483

Short mode:1~495

Reset Are You Sure

Config Settings

DMX Channel Mode

(Default is：Standard mode)

Standard mode 25

Extended mode 30

Short mode 18

Pan Tilt Swap

(Default is: OFF)

OFF

Pan Tilt Swap off

Pan Tilt Swap on

Pan Tilt Invert

(Default is: OFF)

OFF

Pan Tilt Invert off

Pan Tilt Invert on

Pan amend 0-127

Tilt amend 0-127

DMX Mode

(Default is: XLR First)

XLR First

XLR Only

Wireless Only

Wireless First

WirelessTo XLR

Unlink Wireless YES

Master Slave Mode

(Default is: slave)

Slave

Master

Factory Settings YES

PRM Transmit YES

Display Options

Language English / Chinese

Display Mode Off After Delay / On

Always

Display Reverse OFF / ON

Display Contrast

(Default is: 9) 0~18

Information

Power On Hours XXXX

Software Version X.X.X

9/22

Test Mode

Self Test YES

Manual Test

Red Dimmer 0-255

Green Dimmer 0-255

Blue Dimmer 0-255

Iris

Effect 1

Effect 2

Effect 3

F-Gobo wheel

NO Gobo

Gobo 1 - Gobo 8

Rotation

Reverse Rotation

Shake 1 ~ 8

Rotating Gobo

NO Gobo

Gobo 1 - Gobo 6

Rotation

Reverse Rotation

Shake 1 ~ 6

Gobo rotation

Stop

Rotation

Reverse Rotation

Frost

Have

Prism Set

Have

Prism Rotate

Stop

Rotation

Reverse Rotation

Focus 0-255

ZOOM 0-255

Pan Location 0-255

Tilt Location 0-255

Pan&Tilt Speed 0-255

10/22

Operation Mode

DMX Operation

Preset Memory

User Memory

Static Scene 1～16

CH1 Strobe 0-255

CH2 Dimmer 0-255

CH3 Red 0-255

CH4 Green 0-255

CH5 Blue 0-255

CH6 Iris 0-255

CH7 F-Gobo 0-255

CH8 R-Gobo 0-255

CH9 Gobo-R 0-255

CH10 Frost 0-255

CH11 Prism Set 0-255

CH12 Prism-R 0-255

CH13 Focus 0-255

CH14Zoom 0-255

CH15Pan 0-255

CH16Tilt 0-255

CH17 P&T Speed 0-255

CH18 Keep Time 0-25 Second

Remark:

1. In the synchronous control of multiple projectors parameters can be transmitted from the master including:

DMX mode, display setting, operation mode(user memory data included);

Explanations for the signs on top-right of the display:

S: Slave M: Master

D: DMX512 Mode I: Preset Memory

U: User’s Memory T: Test Mode

Lock Sign:

It means the buttons are locked , the sign will disappear and buttons be unlocked after Press button are pressed

for more than 3 seconds.

Inhaltsverzeichnis

Andere PR Lighting DJ-Equipment Handbücher

PR Lighting

PR Lighting MEGA COLOUR 2000 Bedienungsanleitung

PR Lighting

PR Lighting XLED 250 BEAM Bedienungsanleitung

PR Lighting

PR Lighting StarBrite Bedienungsanleitung

PR Lighting

PR Lighting XR-230 BEAM Bedienungsanleitung

PR Lighting

PR Lighting XS 250 Bedienungsanleitung

PR Lighting

PR Lighting JNR PAR COB Bedienungsanleitung

PR Lighting

PR Lighting MEGA 4000 Bedienungsanleitung

PR Lighting

PR Lighting AQUA 350 BEAM PR-2368 Bedienungsanleitung

PR Lighting

PR Lighting PILOT 300 Bedienungsanleitung

PR Lighting

PR Lighting PR-8802 Bedienungsanleitung

PR Lighting

PR Lighting XPar 390 Bedienungsanleitung

PR Lighting

PR Lighting ARC LED 3108 Bedienungsanleitung

PR Lighting

PR Lighting XLED 1037 Bedienungsanleitung

PR Lighting

PR Lighting AQUA LED 600 SPOT Bedienungsanleitung

PR Lighting

PR Lighting JNR-8119A Bedienungsanleitung

PR Lighting

PR Lighting XR 380 Beam Bedienungsanleitung

PR Lighting

PR Lighting JUNIOR JNR PAR ZOOM 3618 Bedienungsanleitung

PR Lighting

PR Lighting AQUA LED 1800 FRAMING Bedienungsanleitung

PR Lighting

PR Lighting XLED 6019 Bedienungsanleitung

PR Lighting

PR Lighting PR-8110 Bedienungsanleitung

PR Lighting

PR Lighting LED Studio 3201D Bedienungsanleitung

PR Lighting

PR Lighting PR-8541 Bedienungsanleitung

PR Lighting

PR Lighting XL 1200 Bedienungsanleitung

PR Lighting

PR Lighting XPar 336-W Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung