PR Lighting XPar 150 Bedienungsanleitung

XPar 150

PR-8202

The user manual contains important information about the safe installation and use of a projector. Please read

and follow these instructions carefully and keep the manual in a safe place for future reference.

PR L GHT NG LTD.

http://www.pr-lighting.com

INDEX

SAFETY AND WARN NGS……………………………………………………………………………………………………

NSTUCT ONS …………………………………………………………………………………………………………………

●CLEAN NG AND MA NTENANCE …………………………………………………………………………………………

●TROUBLESHOOT NG…………………………………………………………………………………………………………

3. APPEARANCE …………………………………………………………………………………………………………………

4. NSTALLAT ON ………………………………………………………………………………………………………………

●R GG NG ………………………………………………………………………………………………………………………

●PLACE A UN T ON A FLAT SURFACE………………………………………………………………………………………

● NSTALLAT ON OF BARN DOOR……………………………………………………………………………………………

●TRANSPORTAT ON……………………………………………………………………………………………………………

●POWER CONNECT ONS ……………………………………………………………………………………………………

●DMX CONTROL CONNECT ON ……………………………………………………………………………………………

●DMX TERM NATOR …………………………………………………………………………………………………………

5. SETUP AND CONF GURAT ON………………………………………………………………………………………………

●FRONT PANEL OPERAT ON…………………………………………………………………………………………………

●DMX START ADDRESS………………………………………………………………………………………………………

●DMX W RELSESS CONTROL ………………………………………………………………………………………………

●STAND-ALONE MODE………………………………………………………………………………………………………

●MASTER/SLAVE MODE………………………………………………………………………………………………………

6.OPERAT ON MENU ……………………………………………………………………………………………………………

7. DMX PROTOCOL ……………………………………………………………………………………………………………

TECHN CAL DATA………………………………………………………………………………………………………………

9.C RCU T D AGRAM AND PCB CONNECT ONS……………………………………………………………………………

●C RCU T D AGRAM …………………………………………………………………………………………………………

●PCB CONNECT ONS…………………………………………………………………………………………………………

10.COMPONENT ORDER CODES ………………………………………………………………………………………………

ACCESSORIES

The following items are supplied with the projector and please check:

Name Quantity Unit Remark

G clamps 1 Pc

Power cord 1 Pc With plug and socket

XLR Cable 2 Pc

Safety cord 1 Pc

User manual 1 Pc

Transparent Cover+ seal+ screws ×6 1 Set Optional

Barn Door 1 Set Optional

Frost panel(Barn Door + Frost panel) 1 Set Optional

Please note that as part of our ongoing co it ent to continuous product develop ent, specifications are

subject to change without notice. Whilst every care is taken in the preparation of the anual we reserve the

right to change specifications in the course of product i prove ent. The publishers cannot be held responsible

for the accuracy of the infor ation herein, or any consequence arising fro the .

Every unit is tested co pletely and packed properly by the anufacturer. Please ake sure the packing and /

or the unit are in good condition before installation and use. Should there be any da age caused by

transportation, consult your dealer and do not use the unit. Any da age caused by i proper use will not be

assu ed by the anufacturer and / or dealer.

1. SAFETY AND WARNINGS

NOTE

Before a projector’s installation, power-on, operation and aintenance, please carefully read

the safety infor ation hereinafter!

The following safety signs are used in the user anual.

Warning

User

Manual

Electrical

shock

Goggles

Protective

Gloves

Fla es

High

Te perature

● When unpacking , check if there is transportation da age before using the projector. Should there be

any da age caused by transportation, consult your dealer and do not use it.

●The manufacture is not responsible for loss caused by the user not following the manual or changing the

projector as he/she likes

●Please be noted that the damage caused by changing the projector at will is not warranted.

● Do not hesitate to contact the dealer or the manufacturer if any questions or advice.

● Use only in dry locations. Keep this unit away from rain and moisture, excessive heat, humidity and dust. Do not

allow contact with water or any other liquids.

●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while

being operated

●The projector is only intended for installation, operation and maintenance by qualified personnel. And the

operation must strictly follow the procedures in the manual

●No repairable parts in the projector and do not open covers for maintenance by yourself.

●Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned.

●Do not connect this device to any type of dimmer pack

●After lamp switched on, the minimum distance between the projector and illuminated surface is 10m

●lens and other optical parts shall be replaced immediately if they have deformed or been damaged, otherwise the

light output will be compromised.

●Before operation, please confirm that all covers(housing) are on and screws tightened. t’s forbidden to use a

projector while covers(housing)are off

●Keep the lamp clean and do not touch it with bare hands.

●While operating it, wear protective items.

●Any electrical connection must be carried out by a qualified person .

●Before installation, please confirm the voltage supplied matches what is required for the projector

●Each projector must be properly earthed and installed as per related electrical standards.

●Do not use power cord with its insulator damaged and connect the power cord with other cables.

● f the projector is not used or under cleaning,, please hold the plug and unplug it. Do not unplug it forcefully or

by pulling the power cable.

●All power cords must conform to related safety and regulations

●While being operated, the projector should not be under rains or in humidity.

●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other

electrical parts’ life will be shortened .

●There are safety cord holes at the bottom of the base of a projector. n view of safety, please run the safety cord

supplied through the safety cord holes for safety support.

●Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from power

mains.

●After running for 5minutes at constant temperature environment, the temperature of the housing of the

projector is 45℃.After stable operation , its temperature is 50℃.

●While the lamp is stricken for the first time, there will be smoke and strange smell. t’s normal and does not

mean the projector has some defects.

●While operated, do not touch the metallic housing. t is very hot during operation.

●Do not mount the projector directly on inflammable surface.

●Do not project the beam straightly on combustible items and the minimum distance between the projector

and illuminated items is 10m.

●A projector should be installed with good ventilation and the minimum distance between the projector and

walls is 50cm. At the same time, please ensure the fans and air inlets and outlets are workable.

2. INSTRUCTIONS

●CLEANING AND MAINTENANCE

The accumulation of oil, smoke and dust on the lens will compromise the light output. Cleaning a projector is very necessary to ensure

a reliable use of it. Without the permission by a qualified person for internal part replacement, it is forbidden to dismantle a unit.

Cleaning frequency is to be decided by operations and its environment. Use soft cloth and normal detergent for glass for cleaning work.

t’s advised external optical system be cleaned every 20days. Keep lens clean and do not touch optical parts with bare hands.

●Before any maintenance and cleaning, please ensure the project is off the power

●Only qualified person is allowed to do maintenance

●During maintenance and before maintenance, the projector must be off power.

●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens whether

it runs or not

●Do not use alcohol or other organic solvent to clean the housing to avoid damage.

●Do not use any solvent with chemical elements to clean color filters or hot mirror.

●TROUBLESHOOTING

PROBLEM ACTION

The projector doesn’t switch on  Check the fuse on the power socket.

 Check the lamp.

The lamp is on but the projector doesn’t respond

to the controller

 Make sure that the fixture’s start address is right

 Replace or repair the XLR signal cable.

The projector functions intermittently  Make sure the fan is working well or fans and their shields are not blocked

Beam appears dim, Low in brightness  Make sure the lamp is within its lifespan

 Remove dust or grease from the lenses.

The project image appears to have a halo  Carefully clean the lamp, optical lenses and other components.

Heavily Defective Beam  Check if lens are in good condition(not cracked)

 Clean dust or grease on the lens.

3. APPEARANCE

(The unit has two different settings. One is with wireless control function and the other version without it. After either

version leaves the factory, they can’t be changed in between as you like)

With wireless control function Without wireless control function

Product’s External Functional Sketch：

No.

Name Remarks

1 Frost panel（Optional） Other components should be selected if frost panel selected

2 Barn Door （Optional）

3 Knob

4 Arm

5 Support

6 Safety cord hole

7 XLR cable Small

8 Power Cord Big

9 Transparent Display Cover（Optional ） Used in harsh environment like dusty area or being under water

10 Wireless Antenna Only Supplied with the version with Wireless control function

11 Butterfly screws nstallation and dismantlement of barn door

4. INSTALLATION

●RIGGING

Before moving the unit, lock the adjusting knob.

Take 1 clamps and the safety cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached to

each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNING on the underside of

the base as shown above) To pass the SAFETY CORD through the HOLES for safety! Always ensure that the projector is firmly

anchored to avoid vibration and slipping whilst functioning. Always ensure that the structure that you are going to mount the projector

to is secure and strong enough to support the weight of the unit

(if the unit is without wireless control function, while being hung, the antenna should face down)

●PLACE A UNIT ON A FLAT SURFACE

Before placing a unit on a flat surface, loosen the small knob with the support and make the angle between the arm and the support

60degrees. Tighten the small knob. Loosen he big knob and adjust the angle between the arm and unit as desired and then tighten it.( f

the unit is with wireless control function, after the unit is placed on a flat surface the antenna should face up)

●INSTALLATION OF BARN DOOR

(Two different accessory options：a. Barn Door ；b. Barn door +Frost panel )

f only barn door, its installation is illustrated in the diagram below:

After loosening the butterfly screws(just loosen them, needn’t remove them) in the front of the head and rotating the holding

components in the shape of 7 by 90 degrees, place the barn door into the holding parts in the shape of 7. The installation is completed

after the holding components are rotated backwards , butterfly screws are tightened, and the safety cord with the barn door is run

through the hole in the iddle of the head. The light closing effect can be reached by moving the barn door blades.

on flat surface with

antenna facing up

Support

Arm

Safety Cord

run through

safety cord hole

hung with antenna

facing down

butterfly screws

holding parts in the

shape of 7

Barn door

Place

f the frost panel is also selected , it must be used in combination of the barn door. ts nstallation and Dismantlement is

illustrated in the diagrams below:

The unit with a barn door is as follow:

●

TRANSPORTATION

Before transportation, tighten both knobs after the arm and support are overlapped.

WARNING:

●

The projector MUST be lifted or carried by the HANDLES instead of clamps.

●

.For safety the safety cord should afford 10 times the Projector’s weight.

●

POWER CONNECTION

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Before power connection, please ensure the power supplied must match what the nameplate says. t is recommended that each

projector be connected with power separately so that they may be individually switched on and off.

Note: f projectors are connected in series, please connect POWER N port of the 1

projector with the Power Mains, then connect its

POWER OUT with POWER N of the 2

projector, and so on till all fixtures are connected. f the voltage supplied is 200V-240V,

the maximum projectors connected is 8pcs, if it is 100V-120V, the maximum is 4pcs. The diameter of the cores of the wires for the

Power in/out cables must be equal or bigger than

2.5mm

2 .

●

The earth wire(yellow/green) ust be connected to the ground. And electrical connection ust be in

accordance with the standards concerned.

●

If any questions about the electrical installation, do not continue but consult a qualified electrician.

screws ×4

frost panel

barn door

●

DMX CONTROL CONNECTION:

Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with

each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the

projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown in the figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets

mustn’t be connected in any way other than mentioned in the above figure. The unit accepts digital control signals in protocol

DMX512 (1990).

Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second

fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX

terminator as shown in the figure below.

●

DMX TERMINATOR

n the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω (ohm) resistor connected across pins 2 and 3, which is then plugged

into the output socket on the last projector in the chain. The connections are illustrated below.

POWER

DMX

CONTROLLER DMX OUT DMX IN

POWER OUT POWER IN POWER OUT POWER IN

DMX OUT DMX IN

DMX

TERMINATOR

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across ins 2 and 3 in an XLR lug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

5. SETUP AND CONFIGURATION

●

FRONT PANEL OPERATION

Projector configuration can be set conveniently via push button and LCD display.

Launch the projector and press button ENTER for more than 3 seconds to unlock the panel, the LCD will show the function menu of

the projector, each main menu has its submenus and each submenu has a specific function. For details, please see the

“OPERAT ON MENU” section.

Press button UP or DOWN if you want to browse through the various Setup Options.

Press button ENTER to save your settings or enter the submenu.

Press button UP or DOWN to change values(plus or minus)

Press button FUNC, it will return to the upper menu. f button FUNC not pressed, the default will show display status automatically.

●

DMX START ADDRESS

Each Projector must be given a DMX start address so that the correct projector responds to the correct control signals. This DMX start

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the

controller. The Unit has 2 DMX modes. There are standard mode and extended mode. For example standard mode has 6 channels,

so set the No. 1 projector’s address 001, No. 2 projector’s address 007, No. 3 projector’s address 013, No. 4 projector’s address019,

and so on.

Launch the projector. Press button ENTER more than 2seconds to unlock panel.

Press button ENTER to display DMX address;

Press button UP and DOWN, you can set the address;

Press button ENTER to confirm; after powered on next time, the default will be last value saved

Press button FUNC, it will return to the upper menu.

●

DMX WIRELESS CONTROL ( f the projector has the function)

The projector has wireless control function with wireless receiver module and antenna for remote control.

The setup of it is below:

1. Enter into the projector’s menu. Select the menu “Config Settigns” via the bottoms of

UP and DOWN

Select DMX control Mode---- Wireless First (Note: do not select XLR ONLY),then wireless indication in the

front panel will be on, meaning wireless control function is activated.

Only after the projector is linked with a transmitter, can it receive wireless signal sent by the transmitter. f unlinking it, Press

“Enter” for the menu of Unlink Wireless under the upper level menu of Config Settigns .

●

STAND-ALONE MODE

Operate the projector without connecting with a controller, enable the master mode through the operation panel, the

projector will run in Stand-Alone mode automatically.

DMX address can be set at any number within 512.

●

MASTER/SLAVE MODE

Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,

connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR control cable and then connect the second

fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the

last fixture’s DMX output to a DMX terminator. Set 1

projector as the master and others are Slaves.

Start Addresses of all Slaves are 001; Operation mode of the Master can be set any mode for a Master’ and Slaves’ operation mode can

be set accordingly.

After Powered on, the group will run in Master/Slave Mode

6. OPERATION MENU

(Those contents within the black box are only for the version with wireless control function)

level enu 2

level enu 3

level enu 4

level enu

DMX Address Standard:001-506

Extended:001-501

Config Settings

DMX Channel Mode

（Default：STD6）

Standard 6

Extended 11

DMX Mode

（Default：XLR First）

（The version without wireless

control does not have the function）

XLR First

XLR Only

Wireless Only

Wireless First

Wireless To XLR

Unlink Wireless

（The version without wireless

control does not have the function）

Yes

LED OuptControl

(Default: No)

Brightness

Timer Control

Master/Slave

（Default：Slave）

Slave

Master

Color Offset

Red 128-255

Green 128-255

Blue 128-255

Language

（Default：English）

English

Chinese

Lcd Light Setup

On Backlight off 3

minutes after no

button pushed

Off

Display nvert Yes

Factory Settings Yes

Parameter Transm Yes

Clean Prgra Yes

nformation

LED Temperature Display of Lamp board temperature

Fixture use Time Display of Fixture time

Software Ver.

X.X.X

Display of Software Version

Test Mode

Red

Green

Blue

White

RGB

RWB

RGBW

Operation Mode

DMX Mode Yes

User Memory Yes

Preset Memory（PR01~PR16）

User Progra Edit

（ET01~ET16）

Dimmer 0-255

Strobe 0-255

Red 0-255

Green 0-255

Blue 0-255

White 0-255

Keep Time 0-255

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PR Lighting DJ-Equipment Handbücher

PR Lighting

PR Lighting StarBrite Bedienungsanleitung

PR Lighting

PR Lighting XL 1200 Bedienungsanleitung

PR Lighting

PR Lighting XPar 348 Bedienungsanleitung

PR Lighting

PR Lighting Theatre Master PR-3010 Bedienungsanleitung

PR Lighting

PR Lighting PR-8242 Bedienungsanleitung

PR Lighting

PR Lighting XRLED 300 SPOT Bedienungsanleitung

PR Lighting

PR Lighting JNR-8119A Bedienungsanleitung

PR Lighting

PR Lighting LED Studio 3300T Bedienungsanleitung

PR Lighting

PR Lighting PR-8110 Bedienungsanleitung

PR Lighting

PR Lighting CSL 1037 Bedienungsanleitung

PR Lighting

PR Lighting XLED 6007 Bedienungsanleitung

PR Lighting

PR Lighting LED Studio 3200T Bedienungsanleitung

PR Lighting

PR Lighting XPar 390 Bedienungsanleitung

PR Lighting

PR Lighting JNR PAR COB Bedienungsanleitung

PR Lighting

PR Lighting AQUA LED 600 SPOT Bedienungsanleitung

PR Lighting

PR Lighting PR-3203T Bedienungsanleitung

PR Lighting

PR Lighting SOLO 575 Bedienungsanleitung

PR Lighting

PR Lighting XR 1000 Framing Bedienungsanleitung

PR Lighting

PR Lighting JUNIOR JNR PAR ZOOM 3618 Bedienungsanleitung

PR Lighting

PR Lighting PILOT 300 Bedienungsanleitung

PR Lighting

PR Lighting XRLED 1200 SPOT Bedienungsanleitung

PR Lighting

PR Lighting XPar 1012 Bedienungsanleitung

PR Lighting

PR Lighting PR-2302 Bedienungsanleitung

PR Lighting

PR Lighting OMEGA Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung