PR Lighting XR480 BWS Bedienungsanleitung

1/30

XR480 BWS

PR-2493

The user manual contains important information about the safe installation and use of a projector. Please read

and follow these instructions carefully and keep the manual in a safe place for future reference.

PR LIGHTING LTD.

http://www.pr-light ing.com

2/30

INDEX

1. SAFETY AND WARNINGS

2. INSTUCTIONS

●CLEANING AND MAINTENANCE

●LUBRICATION

●TROUBLESHOOTING

3. APPEARANCE

4. INSTALLATION

●RIGGING

●POWER CONNECTIONS

●DMX CONTROL CONNECTIONs

●DMX TERMINATOR

●ALIGNMENT/INSTALLATION/REPLACEMENT OF A LAMP

●GOBO/COLOR FILTER REPLACEMENT

5. SETUP AND CONFIGURATION

●FRONT PANEL OPERATION

●DMX START ADDRESS

●DMX WIRELSESS CONTROL

●STAND-ALONE MODE

●MASTER/SLAVE MODE

6.OPERATION MENU

7. DMX PROTOCOL

8. LOGOS

9. ERROR MESSAGES

10.TECHNICAL DATA

11.CIRCUIT DIAGRAM AND PCB CONNECTIONS

●CIRCUIT DIAGRAM

●PCB CONNECTIONS

12.COMPONENT ORDER CODES

ACCESSORIES

The following items are supplied with the projector and please check:

Name

Quantity

Unit

Remark

G clamps

Pcs

XLR Signal Cable

Set

With Male and female sockets

Safety cord

User

manual

Ω clamps

Pcs

Optional

Please note that as part of our ongoing commitment to continuous product development, specifications are

subject to change without notice. Whilst every care is taken in the preparation of the manual we reserve the

right to change specifications in the course of product improvement. The publishers cannot be held responsible

for the accuracy of the information herein, or any consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and /

or the unit are in good condition before installation and use. Should there be any damage caused by

transportation, consult your dealer and do not use the unit. Any damage caused by improper use will not be

assumed by the manufacturer and / or dealer.

Note: For the products made by Guangzhou PR lighting Ltd, the warranty for the whole product is one year starting from

the delivery date but the light source is not within the warranty.

3/30

1. SAFETY AND WARNINGS

NOTE

Before a projector’s installation, power-on, operation and maintenance, please carefully read

the safety information hereinafter!

The following safety signs are used in the user manual.

Warning

User

Manual

Electrical

shock

Goggles

Protective

Gloves

Flames

High

Temperature

● When unpacking , check if there is transportation damage before using the projector. Should there be any

damage caused by transportation, consult your dealer and do not use it.

●The manufacture is not responsible for loss caused by the user not following the manual or changing the projector

as he/she likes.

●Please be noted that the damage caused by changing the projector at will is not warranted.

● Do not hesitate to contact the dealer or the manufacturer if any questions or advice.

● The projector is for indoor use only, IP20.

● Use only in dry locations. Keep this unit away from rain and moisture, excessive heat, humidity and dust. Do not

allow contact with water or any other liquids.

●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while

being operated.

●The projector is only intended for installation, operation and maintenance by qualified personnel. And the

operation must strictly follow the procedures in the manual.

●No repairable parts in the projector and do not open covers for maintenance by yourself.

●Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned..

●Do not connect this device to any type of dimmer pack.

●After lamp switched on, the minimum distance between the projector and illuminated surface is 10m.

●lens and other optical parts shall be replaced immediately if they have deformed or been damaged, otherwise the

light output will be compromised.

●Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use a

projector while covers(housing)are off .

●Keep the lamp clean and do not touch it with bare hands.

●While operating it, wear protective items.

●Any electrical connection must be carried out by a qualified person .

●Before installation, please confirm the voltage supplied matches what is required for the projector.

●Each projector must be properly earthed and installed as per related electrical standards.

●Do not use power cord with its insulator damaged and connect the power cord with other cables.

●If the projector is not used or under cleaning,, please hold the plug and unplug it. Do not unplug it forcefully

or by pulling the power cable.

●All power cords must conform to related safety and regulations.

●While being operated, the projector should not be under rains or in humidity.

●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other

electrical parts’ life will be shortened .

●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety

4/30

cord supplied through the safety cord holes for safety support.

●Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from

power mains.

●After running for 30minutes, the temperature of the housing of the projector is 45℃.After stable operation ,

its temperature is 90℃.

●While the lamp is stricken for the first time, there will be smoke and strange smell. It’s normal and does not

mean the projector has some defects.

●Do not mount the projector directly on inflammable surface.

●Do not project the beam straightly on combustible items and the minimum distance between the projector

and illuminated items is 10m.

●A projector should be installed with good ventilation and the minimum distance between the projector and

walls is 50cm. At the same time, please ensure the fans and air inlets and outlets are workable.

2. INSTRUCTIONS

●CLEANING AND MAINTENANCE

If a projector can’t start. Please check if the fuse is blown up. If it does, replace it with a new fuse with same ratings. And the

projector has over-temperature protective device. If the temperature is too high, the protective device will be triggered to shut the

projector off. When it happens, please check if the fans run normally or fan shield is blocked by dust. After the issue is solved,

restart the projector.

The accumulation of oil, smoke and dust on the lens will compromise the light output. Cleaning a projector is very necessary to

ensure a reliable use of it. Cooling fans need to be cleaned every 15days. Internal lens, reflector and hot mirror need to be cleaned

periodically to optimize light output.

Cleaning frequency is to be decided by operations and its environment. Use soft cloth and normal detergent for glass for cleaning

work. It’s advised external optical system be cleaned every 20days and internal optical systems every 30/60days. Keep lens clean

and do not touch optical parts with bare hands.

●Before any maintenance and cleaning, please ensure the project is off the power.

●Only qualified person is allowed to do maintenance.

●During maintenance and before maintenance, the projector must be off power.

●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens

whether it runs or not.

●Do not use alcohol or other organic solvent to clean the housing to avoid damage.

●Do not use any solvent with chemical elements to clean color filters or hot mirror.

●LUBRICATION

To ensure smooth movement of gobos and zoom and focus lens, it’s advised rotators’ bearings and 2 sliding bars for zoom and

focus lens be lubricated every 2 months. High quality and high temperature lubricant/grease is advised..

●TROUBLESHOOTING

PROBLEM ACTION

The projector doesn’t switch on  Check the fuse on the power socket.

 Check the lamp.

The lamp is on but the projector doesn’t respond

to the controller

 Make sure that the fixture’s start address is right

 Replace or repair the XLR signal cable.

The projector functions intermittently  Make sure the fan is working well or fans and their shields are not blocked

Beam appears dim, Low in brightness  Make sure the lamp is within its lifespan

 Remove dust or grease from the lenses.

The project image appears to have a halo  Carefully clean the lamp, optical lenses and other components.

Heavily Defective Beam  Check if lens are in good condition(not cracked)

 Clean dust or grease on the lens.

5/30

3. APPEARANCE

1. Front Lens

2. Lens Cover

3. Head Cover

4. Tilt Lock

5. Handle

6. Arm Cover

7. Pan Lock

While transportation, the head should be locked-Tilt Lock(4) and Pan Lock(6) should be at locking positions.

Before the use of the projector, unlock both.

Rear Panel of the Base

1. Power Switch

2. Fuse Holder

3. Power Socket

4. 3-Pin XLR Socket(Male)

5. Wireless Antenna(Only for projector

requested for wireless control)

6. 3-Pin XLR Socket(Female)

7. 5-Pin XLR Socket(Male)

4. INSTALLATION

● RIGGING

Before moving a projector, Please lock Pan and Tilt. Before its operation, please unlock them. It’s forbidden to run a

projector with power while it is locked.

Touch Screen

Escape/Left Key

Up key

Down Key

Right Key

6/30

Warning

please run the safety cord

through the two holes for safety

Safety cord

Handle

Clamp

Control menu

Take 2 clamps and the safety cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached

to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNING on the

underside of the base as shown above) To pass the SAFETY CORD through the HOLES for safety! Always ensure that the

projector is firmly anchored to avoid vibration and slipping whilst functioning. Always ensure that the structure that you are going

to mount the projector to is secure and strong enough to support the weight of a XR 1000 Framing.

WARNING:

●The projector MUST be lifted or carried by the HANDLES instead of clamps.

●.For safety the safety cord should afford 10 times the Projector’s weight.

● POWER CONNECTION

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended that each

projector be connected with power separately so that they may be individually switched on and off.

●The earth wire(yellow/green) must be connected to the ground. And electrical connection must be in accordance

with the standards concerned.

●If any questions about the electrical installation, do not continue but consult a qualified electrician.

7/30

●DMX CONTROL CONNECTION:

Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with

each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the

projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown in the figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets

mustn’t be connected in any way other than mentioned in the above figure. The XR330BWS accepts digital control signals in protocol

DMX512 (1990).

Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second

fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX

terminator as shown in the figure below.

●DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120 (ohm) resistor connected across pins 2 and 3, which is then plugged

into the output socket on the last projector in the chain. The connections are illustrated below.

DMX

Controller

DMX512

Input Output Input Output Input

DMX　

Terminator

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

8/30

● ALIGNMENT/INSTALLATION/REPLACEMENT OF A LAMP

Lock the yoke before fitting/replacingthe lamp. Just as Shown by Figure 1, after Opening the cover at the rear of the projector by

loosening 8 fastfit screws, you can open the head. To adjust the lamp as per Figure 2. Take out the lamp as per the figure 3.

Before lamp installation, tighten its power wires well. Lamp in and out are opposite orders

●Don’t touch the internal surface of the reflector and the burner of the lamp with bare hands so as not to

impair the beam output. While lamp’s installation, do not damage the metal wire around the burner.

●Please read "Instructions " enclosed with the lamp

●Do operate the projector while adjusting the lamp

4. After the lamp is aligned well, use cross

screwdriver to tighten the tightening screws at

one side of the lamp to avoid it being loosened

based on procedure 2

2.Loosen a tightening screw by a

cross screw driver at the lamp's side

Figure1:Loosen 8pcs of fastfit

screws

3.To adjust the two screws by a cross

screw driver to change the lamp's position

1.Loosen 4 screws at the fan's two sides

Figure2： Lamp adjustment

9/30

●GOBO REPLACEMENT

DANGER!

Before replacement of gobos, the projector must be off the power.

2. Remove the lamp's two wires and push

it obliquely for the removal.

2.Remove the cover after its 4 screws are

loosened by a cross screwdriver

4.Connect the lamp wires after a new lamp is in place,

and align and tighten the lamp as per figure2

Figure3：Removal of lamp

1.Loosen a tightening screw at the lamp's side

Figure 2

Rotating gobo wheel

Rotator

Gobo

Tightening

spring

Gobo replacement

1. As shown in figure1, disconnect a projector from power. Unfasten

the 4 fastfit screws of the cover to remove the cover, and unfasten

the 2 screws of the fan assembly and remove the assembly.

2.Pull out the rotator from the rotating gobo wheel forcefully by

fingers as shown in figure2 After replacing the gobo or the rotator,

put the rotator back to the holder.

unfasten 2

screws using a

cross screw

driver

remove the fan

component

Figure 1

10/30

5. SETUP AND CONFIGURATION

●FRONT PANEL OPERATION

The projector configuration can be set conveniently via push buttons and color touch screen.

To browse through or change the projector ’s settings, touch the white area of the touch screen or press OK button for more than

3s(Only powered by the battery, pressing the OK button) to unlock the screen , then press ► key to enter the projector ’s function

menus. Each main menu has its sub-menus. And each menu stands for special function. For the details, please see the following 6th

point ”Operation Menu”.:

1. At the page to set the fixture’s functions, press ◄,►,▲,▼ keys or their respective icons to select the functions

desired.

2. While at 2nd,3rd and 4th level of menus, the◄ key is for ESCAPE, but ► key won’t work, and OK key is used for ENTER.

Press OK key to save the changes or enter into the sub menus. Press ▲or ▼ keys to change the numbers(minus or plus).

Or touch the option needed for change.

Shortcut keys: After the Function Menu is entered into, there are all options for the functions on the top of the screen. On the

right there are 4 shortcut keys like ←,→ Lamp Control and English/Chinese.

● DMX START ADDRESS

Each projector must be given a DMX start address so that the correct projector responds to the correct control signals. This DMX start

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the

controller. The projector has 3DMX modes. There are standard mode ,short mode and extended mode. For example standard mode

has 28 channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 029, No. 3 projector’s address 057,No. 4

projector’s address 085, and so on.

Switch on the Projector . Press OK key more than 3 seconds to unlock panel, then press ► key to enter into the fixture’s

operation menus.

Select DMX Address icon and press OK key or touch the icon directly on the display and select DMX address at the 2nd level menu

for the address setting.

Press▲ or ▼ keys or touch<、>displayed for the DMX address desired.

Press OK key to confirm.

Press the◄ key to go back to the upper level menu.

●DMX WIRELESS CONTROL (Only for the fixtures required for the wireless control)

The projector has wireless control function with wireless receiver module and antenna for remote control.

The setup of it is below:

1. Press OK for more than 3s to unlock the control panel, then press ► key to enter into the operation menu

and select “Config Settings”.

2. Select “Wireless First” or “Wireless Only” from the menu of “Signal Select”.

Only after the projector is linked with a transmitter, can it receive wireless signal sent by the transmitter. If unlinking it,

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PR Lighting DJ-Equipment Handbücher

PR Lighting

PR Lighting PR-8242 Bedienungsanleitung

PR Lighting

PR Lighting XPar 150 Bedienungsanleitung

PR Lighting

PR Lighting ARC LED 3108 Bedienungsanleitung

PR Lighting

PR Lighting XRLED 1200 SPOT Bedienungsanleitung

PR Lighting

PR Lighting MEGA 4000 Bedienungsanleitung

PR Lighting

PR Lighting XR480S BWS Bedienungsanleitung

PR Lighting

PR Lighting LED Studio 3200T Bedienungsanleitung

PR Lighting

PR Lighting MEGA COLOUR 2000 Bedienungsanleitung

PR Lighting

PR Lighting LED Studio 3201D Bedienungsanleitung

PR Lighting

PR Lighting XLED 250 BEAM Bedienungsanleitung

PR Lighting

PR Lighting PR-8102 Bedienungsanleitung

PR Lighting

PR Lighting JNR-8119A Bedienungsanleitung

PR Lighting

PR Lighting XR 380 Beam Bedienungsanleitung

PR Lighting

PR Lighting Theatre Master PR-3010 Bedienungsanleitung

PR Lighting

PR Lighting PR-3203T Bedienungsanleitung

PR Lighting

PR Lighting XS 250 Bedienungsanleitung

PR Lighting

PR Lighting PR-8541 Bedienungsanleitung

PR Lighting

PR Lighting XLED 3007 Bedienungsanleitung

PR Lighting

PR Lighting XR 1700 FRAMING Bedienungsanleitung

PR Lighting

PR Lighting PILOT 300 Bedienungsanleitung

PR Lighting

PR Lighting XL 1200 Bedienungsanleitung

PR Lighting

PR Lighting Junior JNR Minifresnel 100MZ-W Bedienungsanleitung

PR Lighting

PR Lighting SOLO 575 Bedienungsanleitung

PR Lighting

PR Lighting JUNIOR JNR-8146C Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung