PR Lighting XLED 1037 Bedienungsanleitung

XLED 1037

PR-8120

This product manual contains important information about the safe installation and use of this projector.

Please read and follow these instructions carefully and keep this manual in a safe place for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

2/16

INDEX

SAFE USAGE OF THE PROJECTOR 3

INSTALLING THE PROJECTOR 4

POWER SUPPLY – MAINS 5

CONTROL CONNECTIONS 5

DMX TERMINATOR 6

SETUP OPTIONS-PROJECTOR CONFIGURATION 6

TO SET THE DMX START ADDRESS 6

OPERATION MENU 7

DMX PROTOCOL 9

INDICATION OF LED DIGITAL TUBE 10

MAINTENANCE 10

KEEPING THE PROJECTOR CLEAN 10

TROUBLESHOOTING 11

TECHNICAL DATA 12

ELECTRICAL DIAGRAM 15

COMPONENT ORDER CODES 16

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without notice. Whilst

every care is taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement. The

publishers cannot be held responsible for the accuracy of the information herein, or any consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good condition

before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the unit. Any damage caused

by improper use will not be assumed by the manufacturer and / or dealer.

ACCESSORIES

These items are packed together with the projector:

Name Quantity Unit Remark

G clamp 2 Pcs

Ω clamp 2 Pcs Optional

XLR cable 1 Pc With Plug & Socket

Safety cord 1 Pc

This manual 1 Pc

3/16

SAFE USAGE OF THE PROJECTOR

When unpacking and before disposing of the carton check there is no transportation damage before using the projector. Should there

be any damage caused by transportation, consult your dealer and do not use the apparatus.

The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture, excessive heat,

humidity and dust. Do not allow contact with water or any other liquids.

DO NOT mount the projector directly onto inflammable surface

The projector is only intended for installation, operation and maintenance by qualified personnel.

The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces. Be sure that no

ventilation slots are blocked.

Do not project the beam onto inflammable surfaces, minimum distance is 5m. 5m

Avoid direct exposure to the light from the lamp. The light is harmful to the eye.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.

Do not connect this device to any other types of dimmer apparatus.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact with other cables.

Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.

Keep a projector’s optical system clean. Do not touch LED lens with bare hands.

The projector should always be installed with a secondary safety fixing. A safety cord is supplied for this; it should be attached as

shown in “installing the projector” section.

Shields and lens shall be changed if they have become visibly damaged to such an extent than their effectiveness is impaired, for

example by cracks or deep scratches.

LED lamps should be replaced if damaged or having reached life limit.

Exterior surface temperatures of the luminaire after 5 minutes operation is55℃, when steady state is achieved 70℃,

There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the covers

removed.

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

Always disconnect a projector from the POWER when not in use or before cleaning or any

maintenance work!

4/16

INSTALL THE PROJECTOR

Take 2 clamps and 1 safety cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached to each

clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNING on the underside of the

base as shown above) Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning. Always

ensure that the structure that you are going to mount the projector is secure and is strong enough to support a weight of each projector.

WARNING:

1. The projector MUST be lifted or carried by the HANDLES instead of clamps.

2. For safety the safety cord should afford 10 times of the unit’s weight.

5/16

POWER SUPPLY-MAINS

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel

of the projector. It is recommended that each projector be supplied separately so that they may be individually switched on and off.

IMPORTANT

It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant standards.

CONTROL CONNECTION

Connection between controller and projector and between one projector and another must be made with a 2 core-screened cable, with

each core having at least a 0.5mm diameter. Connection to and from the projector is via cannon 5 pin (which are included with the

projector) or 3 pin XLR plugs and sockets. The XLR's are connected as shown in the figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of the plug is not

connected in any way. The projector accepts digital control signals in protocol DMX512 (1990).

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input and connect

the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown in the figure below.

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

6/16

electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120 (ohm) resistor connected across pins 2 and 3, which is then plugged

into the output socket on the last projector in the chain. The connections are illustrated below.

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

SETUP OPTIONS-PROJECTOR CONFIGURATION

Projector configuration can be set conveniently via press button switch and LCD display.

To browse or change its setup options, Press button ENTER more than 5 seconds to unlock panel. Menu will be displayed on the

screen, each menu has it own sub-menu. Each menu has specific function, Please refer to “Operation Menu” for details.

Press button UP or DOWN if you want to browse or change through the various Setup Options.

Press button ENTER to save your settings or enter the next menu.

Press button UP or DOWN to change values.(Add or subtract)

Press button FUNC, it will return to the upper menu one by one.

TO SET THE DMX START ADDRESS

Each projector must be given a DMX start address so that the correct projector responds to the correct control signals. This DMX start

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the

controller. The fixture have 2 DMX modes. There are standard mode and extended mode. For example standard mode has 15

channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 016, No. 3 projector’s address 031, No. 4 projector’s

address 046 and so on.

Launch the projector. Press button ENTER more than 5 seconds to unlock panel.

Press button ENTER to display DMX address;

Press button UP and DOWN, you can set the address;

Press button ENTER to confirm while Green Indication flashes, which means the projector has saved the Start Address automatically,

when powered on next time, it will display the value saved last time.

Press button FUNC, it will return to the upper menu one by one.

OPERATION MENU

7/16

1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL

AddR

(DMX address)

XXX

（XXX:1~512）

CNFG

(Config settings)

dmX

(DMX mode，Default: STD)

STd

(Standard mode)

EXT

(Extended mode)

dISP

(Display settings Default: ON)

OFF

(Shut off digital CRT without

pressing buttons in 5 minutes)

xyCH

Pan and Tilt Swap

(Default: OFF)

OFF

xyCP

Pan and Tilt Invert

(Default: OFF)

OFF

DMXS

DMX signal Source Options

(default: PRCA)

PRCA

Cable Signal First

ONCA

Cable Signal Only

ONwR

Wireless Signal O

nly

PRwR

Wireless Signal First

wTOC

Change

From Wireless to Cable

mORS

(Master /Slave Settings,

Default: SLV)

SLAV

(Slave)

mAST

Master(1)

PAIR

Pair disabled

yES

FACT

(Reset factory setup) yES

TRmd

(Transmit

parameters

) yES

INFO

(Information)

TImE

(Fixture usage time) XXXX

VER

(Software Version) X.X.X

TEST

(Test mode)

LAMP

OFF

(red)

(green)

(blue)

(white)

(Yellow)

(Cyan)

(Purple)

RGB

(White)

RGBW

(All On)

Zoom 000-255

Pan 000-255

8/16

Tilt 000-255

RESE Yes

(Operation mode)

dmx

(DMX mode)

PRUN

(Preset memory）

ERUN

(User memory)

ET XX

(User memory,ET01~ET16）

CH01

Strobe 000-255

CH02

Red Dimming 000-255

CH03

Green Dimming 000-255

CH04

Blue Dimming 000-255

CH05

White Dimming 000-255

CH06

Zoom

000-255

CH07

Pan 000-255

CH08

Tilt

000-255

CH09

Pan and Tilt Speed 000-255

CH10

Static Scene Hold Time

000

255

Time=X*40ms

Note:

1. There is only one Projector to be set as a Master in a signal Cable. If Master’s functions used, Please disable DMX control

signal.

2. When multiple projectors’ work together in synchronous control state, Parameters can be transmitted from the master

projector to the slave projectors such as DMX channel mode, Display setting status and operation mode (User memory

data is included). Before parameters transmitted, the projector which will send parameters should be set as a Master and

others be as Slaves.

9/16

DMX PROTOCOL

Standard

mode

Extended

mode FUNCTION DMX DESCRIPTION

1 1 Strobe 000-015 No Strobe

016-255 Speed form Slow to Fast

2 2 Dimmer 000-255 Linear Dimming from Dark to Bright

3 Dimmer Fine 000-255 Dimmer in 16Bit

3 4 Color Macros

000-031 NO

032-063 Red

064-095 Green

096-127 Blue

128-159 Yellow

160-191 Cyan

192-223 Purple

224-255 White

5 Area 1 RED 000-255 Area 1 Red- Linear adjustment from Light to Dark

6 Area 2 RED 000-255 Area 2 Red- Linear adjustment from Light to Dark

7 Area 3 RED 000-255 Area 3 Red- Linear adjustment from Light to Dark

8 Area 1 Green 000-255 Area 1 Green- Linear adjustment from Light to Dark

9 Area 2 Green 000-255 Area 2 Green- Linear adjustment from Light to Dark

10 Area 3 Green 000-255 Area 3 Green- Linear adjustment from Light to Dark

11 Area 1 Blue 000-255 Area 1 Blue- Linear adjustment from Light to Dark

12 Area 2 Blue 000-255 Area 2 Blue- Linear adjustment from Light to Dark

13 Area 3 Blue 000-255 Area 3 Blue- Linear adjustment from Light to Dark

14 Area 1 White 000-255 Area 1 White- Linear adjustment from Light to Dark

15 Area 2 White 000-255 Area 2 White- Linear adjustment from Light to Dark

16 Area 3 White 000-255 Area 3 White- Linear adjustment from Light to Dark

8 17 Zoom 000-255 Linearly Zooming(0°-100 °)

9 18 Zoom Fine 000-255 Zoom in 16 Bit

10 19 PAN 000-255 Pan( 0°~540°)

11 20 Pan Fine 000-255 Pan in 16bit precision

12 21 Tilt 000-255 Tilt(0°~270°)

13 22 Tilt Fine 000-255 Tilt in 16bit precision

14 23

Pan and tilt

Speed

000-255 Pan & Tilt Speed from Fast to Slow

15 24 Control 000-048 Reserved

049-255 Reset

10/16

INDICATION OF LED DIGITAL TUBE

Decimal point of the first digital tube On DMX signal OK

Off No DMX signal

Decimal point of the third digital tube On Master / slave signal is OK

Off No master / slave signal

Decimal point of the fourth digital tube On When setting master mode

Off When setting slave mode

Parameters that LED digital tubes display Flash Parameters not saved, press “ENTER” to save them

MAINTENANCE

To prolong a Projector’s life, Regular maintenance should be done for its LED optical System to ensure that the system be in best

operational condition. If the projector does not function, check the fuses on the power socket of the projector, if burned, they should

only be replaced by fuses of the same specification. Should these be damaged call a qualified technician before replacement. The

projector has thermal protection device that will switch off the projector in case of overheating, should this occur, check if the fans

work normally or fan and fan shield are blocked by dust. If the projector not operational, call a qualified technician. After cleaned and

repaired, the projector can be restarted.

Any maintenance work should only be carried out by qualified technicians.

KEEPING THE PROJECTOR CLEAN

It definitely necessary to keep a projector clean for its reliable use. Cooling fans and their shield should be cleaned every 15days. LED

lamps’ lens and cover should be cleaned regularly for optimized light output.

Cleaning frequency depends on how often a projector is used and its operational environment. A soft cloth and typical glass cleaning

products should be used in cleaning. It is recommended to clean the external optics at least once every 20 days.

Do not use any organic solvent, e.g. alcohol, to clean t housing of the apparatus.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PR Lighting DJ-Equipment Handbücher

PR Lighting

PR Lighting PR-8110 Bedienungsanleitung

PR Lighting

PR Lighting PILOT 300 Bedienungsanleitung

PR Lighting

PR Lighting JNR PAR COB Bedienungsanleitung

PR Lighting

PR Lighting LED STUDIO 3605 Bedienungsanleitung

PR Lighting

PR Lighting SOLO 575 Bedienungsanleitung

PR Lighting

PR Lighting XLED 3007 Bedienungsanleitung

PR Lighting

PR Lighting XR480 BWS Bedienungsanleitung

PR Lighting

PR Lighting XR-230 BEAM Bedienungsanleitung

PR Lighting

PR Lighting JUNIOR JNR PAR ZOOM 3618 Bedienungsanleitung

PR Lighting

PR Lighting Pro Stage 150 RGBW 19 Bedienungsanleitung

PR Lighting

PR Lighting OMEGA Bedienungsanleitung

PR Lighting

PR Lighting PR-3203T Bedienungsanleitung

PR Lighting

PR Lighting AQUA LED 600 SPOT Bedienungsanleitung

PR Lighting

PR Lighting PR-8541 Bedienungsanleitung

PR Lighting

PR Lighting XR480S BWS Bedienungsanleitung

PR Lighting

PR Lighting XR480 BEAM Bedienungsanleitung

PR Lighting

PR Lighting PR-8330 Bedienungsanleitung

PR Lighting

PR Lighting XR 1700 FRAMING Bedienungsanleitung

PR Lighting

PR Lighting AQUA 350 BEAM PR-2368 Bedienungsanleitung

PR Lighting

PR Lighting JNR DOT BEAM Bedienungsanleitung

PR Lighting

PR Lighting XLED 300 Beam Bedienungsanleitung

PR Lighting

PR Lighting Theatre Master PR-3010 Bedienungsanleitung

PR Lighting

PR Lighting MEGA COLOUR 2000 Bedienungsanleitung

PR Lighting

PR Lighting AQUA LED 1800 FRAMING Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung