PR Lighting AQUA LED 1800 FRAMING Bedienungsanleitung

AQUA LED 1800 FRAMING

PR-8169

This product manual contains important information about the safe installation and use of this projector.

Pleaseread andfollowthese instructions carefullyandkeep thismanualin a safeplaceforfuturereference.

PR LIGHTING LTD.

http://www.pr-lighting.com

INDEX

1. SAFETYANDWARNINGS. …………………………………………………………………………………

2. INSTRUCTIONS ……………………………………………………………………………………………

●CLEANINGANDMAINTENANCE ………………………………………………………………………

●LUBRICATION………………………………………………………………………………………………

●TROUBLESHOOTING ……………………………………………………………………………………

3.APPEARANCE…………………………………………………………………………………………………

4.INSTALLATION ………………………………………………………………………………………………

●RIGGING……………………………………………………………………………………………………

●POWERCONNECTIONS ………………………………………………………………………………

●DMXCONTROLCONNECTION…………………………………………………………………………

●DMXTERMINATOR ………………………………………………………………………………………

●REPLACEMENTOFGOBOS………………………………………………………………………………

5.SETUPANDCONFIGURATION………………………………………………………………………………

●FRONTPANELOPERATION………………………………………………………………………………

●DMXSTARTADDRESS……………………………………………………………………………………

●DMXWIRELESSCONTROL………………………………………………………………………………

●STAND-ALONEMODE ……………………………………………………………………………………

●MASTER/SLAVEMODE……………………………………………………………………………………

6.OPERATIONMENU …………………………………………………………………………………………

7.DMXPROTOCOL ……………………………………………………………………………………………

8.LOGOS ONTHE SCREEN……………………………………………………………………………………

9. ERRORINFORMATION ……………………………………………………………………………………

10.TECHNICALDATA …………………………………………………………………………………………

11.CIRCUITDIAGRAMANDPCBCONNECTIONS ……………………………………………………………

●CIRCUITDIAGRAM…………………………………………………………………………………………

●PCB CONNECTIONS…………………………………………………………………………………………

12.COMPONENTORDERCODES………………………………………………………………………………

Thefollowingitemsaresuppliedwiththeprojector andplease check:

Name

Quantity

Unit

Remark

Gclamp

Pcs

XLRconnector

Set

Maleandfemale

Safetycord

Thismanual

Ω clamp

Pcs

Optional

Power Cord

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change

without notice. Whilstevery care istakeninthepreparationof themanualwereservetherightto changespecificationsinthe

course of product improvement. The publisherscannot be heldresponsible forthe accuracyof the information herein,orany

consequencearisingfromthem.

Every unit istested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are

in good condition before installation and use. Should there be any damage caused by transportation, consult your dealer and

donotusetheunit.Anydamage causedbyimproperusewillnot beassumedbythe manufacturerand/ordealer.

Anyfuturetechnicalchangesarenotsubject tofurthernotice.

Note: Forthe products made by Guangzhou PR lighting Ltd, the warranty for the whole product is one year starting from

thedelivery datebutthelightsourceisnotwithinthewarranty.

1. SAFETYANDWARNINGS

NOTE

Before a projector’s installation, power-on, operation and maintenance, please carefully read

thesafety informationhereinafter!

Thefollowingsafetysignsareusedinthe usermanual.

Warning

User

Manual

Electrical

shock

Goggles

Protective

Gloves

Flames

High

Temperature

● When unpacking , checkifthere istransportation damage before using the projector. Should there be any

damagecausedbytransportation,consultyourdealeranddonotuseit.

●The manufacture is not responsible for loss caused bythe user not following the manualor changing the projector

ashe/shelikes

●Please be notedthatthedamage causedby changingthe projector atwill isnot warranted.

● Do not hesitate to contact the dealerorthe manufacturer if anyquestionsor advice.

● Theprojectoris forindoorandoutdoor use,IP65.

● Itcanbeusedinhumidanddusty areas.And itcancontactwater andothernon-corrosiveliquids.

●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while

beingoperated

●The projector is only intended for installation, operation and maintenance by qualified personnel. And the

operationmuststrictlyfollowtheproceduresinthemanual

●Theprojectorisnotfora userforanyreplacementsand theusershouldn'topentheprojectorforrepairand

maintenance.

●Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned.

●Do notconnectthisdevice toany typeofdimmer pack

●After lamp switched on, the minimumdistancebetweentheprojectorand illuminatedsurfaceis5m

●If there are visible damages onthe lamp, lens and protective cover for the screen, i.e., to the extent which affects

itsperformancelikecrackingordeformation,pleasestopusingitandcontactthemanufacturefortheir

replacementwithoriginalparts,otherwiseitsperformancewillbecompromised

.For the location of a lighting fixture, it shouldn’t be seen in the distance of less than 4 meters.

●Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use a

projectorwhilecovers(housing)areoff

●Keep thelampcleananddo nottouchitwithbarehands.

●While operatingit, wearprotectiveitems.

●Anyelectricalconnectionmustbecarriedoutbyaqualifiedperson.

●Before installation, pleaseconfirm thevoltagesupplied matcheswhatisrequired fortheprojector

●Eachprojectormustbeproperlyearthedand installed asperrelatedelectrical standards.

●Do notusepowercord withitsinsulatordamagedand connectthepowercord withothercables.

●If the projector is not used or under cleaning,, please hold the plug and unplug it. Do not unplug it forcefully

orbypullingthepower cable.

●All power cords mustconformto relatedsafetyand regulations

●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other

electrical parts’ life will be shortened .

●The projectorisofclassIP65,and notusedintheenvironment higher thanit.

●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety

cord suppliedthroughthesafetycordholesforsafetysupport.

●Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from

powermains.

●After running for 5minutes, the temperature ofthe housing of the projector is45℃.After stable operation ,

itstemperatureis80℃.

●While the lamp is stricken for the first time, there will be smoke and strange smell. It’s normal and does not

meanthe projectorhas somedefects.

● Don’t touch the covers of the working projector(They are very hot!)

● While a lighting fixture works properly under normal ambient temperature, the maximum temperature of the external surface of the

control device(The integrated control device means the external surface of the housing of the lighting fixtures electric

chamber)allowed is75Celsiusdegrees.

●Do notmounttheprojectordirectlyoninflammablesurface.

●Do not project the beam straightly on combustible items and the minimum distance between the

projectorandilluminateditemsis5m.

●Aprojector should be installed with good ventilation and the minimum distance between the projector

andwallsis50cm.Atthesametime,pleaseensurethefansand airinletsandoutletsare workable.

2. INSTRUCTIONS

●CLEANINGANDMAINTENANCE

If a projector can’t start. Please check if the fuse is blown up. If it does, replace it with a new fuse with same ratings. And the

projector has over-temperature protective device. Ifthe temperature is too high, the protective device will be triggered to shut the

projector off. When it happens, please check if the fans run normally or fan shield is blocked by dust. After the issue is solved,

restart theprojector.

The accumulationof oil, smoke and dust on the lens will compromise the light output. Cleaning a projector is verynecessary to

ensurea reliable use ofit. Cooling fans need to be cleaned every15days. Internal lens, reflectorand hot mirror need to be cleaned

periodicallytooptimize lightoutput.

The cleaning frequencyof cooling fans and heat sinkis decided bythe operations, environment and climate. It isadvised to clean

itevery15daysorless.Userubber orbushorother non-metallic tools to carry out cleaning. The tools can’t scratch or deform the

heatsinkand fans.

Cleaning frequency is to be decided byoperations and itsenvironment. Use soft cloth and normaldetergent for glassfor cleaning

work. It’s advised external optical system be cleaned every 20days and internal optical systems every 30/60days. Keep lens clean

anddo not touchoptical parts with bare hands.

Specialnote:

It’s normal phenomena that there will be mild water mist on the lens while the waterproof product is in use.

●Beforeanymaintenance and cleaning,please ensuretheprojectisoff thepower

●Onlyqualified personis allowedtodo maintenance

●During maintenanceandbefore maintenance, the projectormustbeoffpower.

●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens

whetheritrunsornot

●Do notusealcoholorotherorganicsolventtocleanthehousingto avoiddamage.

●Do notuseanysolventwithchemicalelementstocleancolorfiltersorhotmirror.

●LUBRICATION

To ensure smooth movement of gobos and focus lens, it’s advised rotators’ bearings and 2 sliding bars for focus lensbelubricated

every2 months. High qualityand high temperature lubricant/greaseisadvised..

●TROUBLESHOOTING

PROBLEM

ACTION

Theprojectorcan’t be switched on

Check if the fuse isburned

Checkifthe powercord is connected well

Check if the switching power supply is bad or not connected well. A

professionaltechnicianisrequired for therepair

Check if the control board is connected well. .Aprofessional technician

isrequired fortherepair

Theprojectorcanbeswitched on, buttheLED

lamp’s brightness can’t be controlled

Check if the LED driver board is connected well. A professional

technicianisrequiredfor therepair

Theprojectorcanbeswitched onnormally,but

notcontrolledbytheDMXcontroller

Makesurethatthe fixture’s startaddressisright

ReplaceorrepairtheXLRsignal cable.

Thebeamisnotbright and itsbrightness

decreasessharply

Makesurethefansare workingwellorfansandtheirshieldsarenotblocked

bydust.

Makesurethattheinternalopticsisclean.

Beam appearsdim, Lowinbrightness

Makesurethe lamp is withinitslifespan

Remove dustorgreasefromthelenses.

Theprojectimageappearstohave ahalo

CarefullycleantheLEDlamp,opticallensesandothercomponents.

HeavilyDefectiveBeam

Checkif lensareingood condition(notcracked)

Cleandustorgreaseonthelens.

3. APPEARANCE

4. INSTALLATION

●RIGGING

During transportation, please lock the projector well; Before the use of projector please unlock the head. It’s forbidden to run the

projectorwithoutunlockPanandTilt.

Head

Arm

Base

3PIN

DMX512

PIN FUNCTION

1 GND

2 DATA-

3 DATA+

DMX INDMX OUT

234

432

5PIN

DMX512

PIN FUNCTION

1 GND

2 DATA-

3 DATA+

4 N/C

5 N/C

DMX IN

DMX OUT

Take 2 clamps and 1 safety cords out from the package and mount 2 clamps on the underside of fixture with 4 retainers attached to

each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNING on the underside of

the base as shown above) Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning.

Always ensure that the structure that you are going to mount the projector is secure and is strong enough to supportthe weight ofthe

fixture.

WARNING:

●TheprojectorMUSTbelifted orcarriedbytheHANDLESinsteadofclamps.

●.For safety the safety cord should afford 10 times the Projector’s weight.

●.Forsafety,itshouldnotbehungbyitssides.

●POWERCONNECTIONS

Connectthepower cord as follows:

L(live)=brown

E(earth) =yellow/green

N(neutral)=blue

Before power connection, please ensure the power supplied must match what the nameplate says. It isrecommended that each

projectorbe connected withpower separatelyso that theymaybeindividuallyswitchedonand off.

●The earth wire(yellow/green) must be connected to the ground. And electrical connection must be in

accordancewiththestandardsconcerned.

●Ifany questionsabout the electrical installation,donotcontinue butconsult aqualifiedelectrician.

● The lighting fixture iswithwaterproof power socket, it should be equipped with same IPrating power

plug.

●DMXCONTROLCONNECTION

Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with

each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the

projector)or5pinXLRplugsand sockets.The XLR'sareconnectedasshowninthefigureabove.

Warning

please runthe safetycords through2 safety

cord holes toensuresafety

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets

mustn’t be connected in any way other than mentioned in the above figure. The projector accepts digital control signals in protocol

DMX512(1990).

Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second

fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX

terminatorasshowninthefigurebelow.

●DMXTERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electricalnoise fromdisturbingandcorruptingtheDMXcontrolsignals.

The DMX terminator is simply an XLR connector with a 120(ohm) resistor connected across pins 2 and 3, which is then plugged

intothe output socketonthelastprojectorinthe chain.The connectionsareillustratedbelow

●REPLACEMENTOFGOBOS

控制器

DMX512

回路插

输入输出输入输出输入

NO.1 NO.2 NO.n

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain. PIN 3

PIN 2

INPUT

DMXTERMINATOR

DMXCONTROLLER

OUTPUT

INPUT

OUTPUT

INPUT

图案片安装滤色片安装

Locktiltand unfasten 4 screws of the small cover of the head. Open the cover and you’ll see the structure as above.

Replacement of the color filter. Pull out the color filter directly by hand asthe figure hereinafterin the sequence 1→2. It’s installation

isinreversesequenceastheremoval（2→1）.

Rotating gobos. Pull out the rotator as the figure hereinafter and the removal is in the sequence 1→2. Remove spring of the gobo

and take the gobo out. Place a new gobo in the rotator with the spring and ensure the spring is in the narrow groove of the

rotator ,i.e. its inner ring, then flatten it. At last use proper tool to push the tightening plate upward for the spring and use

anotherhandtohelpplacetherotatorin theoriginalplace. It is in the reverse sequence of the removal2→1.

Note: Do not touch color filters and glass gobos with bare hands. There should be clean and soft paper or cloth between hand and

glass.Installthechamber cover,tighten4 innerhexagonscrewsandunlockTilt.

DANGER!

BEFORETHEREPLACEMENTOFGOBOANDCOLORFILTER,THEPROJECTORMUSTBEOFF

POWER.

5.SETUPANDCONFIGURATION

●FRONTPANELOPERATION

GoboInstallation

Fixgobowheel

Rotatinggobowheel

Colorwheel

Projectorconfigurationcanbesetconveniently viapushbuttonandcolortouchscreen.

Launch the projector and press button ENTER for more than5 secondsto unlock the panel, the LCD will show the function menu of

the projector, each main menu has its submenus and each submenu has a specific function. For details, please see the

“OPERATION MENU” section.

Pressbutton UP or DOWN ifyouwanttobrowsethroughthevariousSetup Options.

Pressbutton ENTER to save your settingsor enterthesubmenu.

Pressbutton UP or DOWN tochangevalues(plusorminus)

Pressbutton FUNC,it willreturnto the uppermenu.Ifbutton FUNC notpressed, thedefault willshowdisplaystatusautomatically.

●DMX STARTADDRESS

Each projector mustbe givena DMX start address so that the correctprojector responds to the correct control signals.This DMX start

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the

controller. The projector has 3 DMX modes. There are short mode ,standard mode and extended mode. For example standard mode

has 38 channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 039, No. 3 projector’s address 077, No. 4

projector’s address115,andsoon.

Launch the projector.Pressbutton ENTER morethan3secondsto unlock panel.

Pressbutton ENTER todisplayDMXaddress;

Pressbutton UP and DOWN, youcansettheaddress;

Pressbutton ENTER to confirm; afterpoweredonnexttime,the defaultwillbelastvalue saved

Pressbutton FUNC,it willreturnto theuppermenu

●DMXWIRELESSCONTROL

Theprojector has wirelesscontrol functionwith wirelessreceivermoduleand antennaforremote control.

Thesetupofitisbelow:

1. Enter into the projector’s menu. Select the menu “Config Settigns” via the bottoms of UP and DOWN

2. Select DMX control Mode---- Wireless First (Note: Do not select XLR ONLY). The DMX wireless control

functionis activated.

Only after the projector is linked with a transmitter, can it receive wireless signal sent by the transmitter. If unlinking it, Press

“Enter” for the menu of Unlink Wireless under the upper level menu of Config Settigns.

●STAND-ALONEMODE

Operate the projector without connecting with a controller, enable the master mode through the operation panel, the

projector will run in Stand-Alone mode automatically.

DMX address can be set at any number within 512.

●MASTER/SLAVEMODE

Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,

connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR control cable and then connect the second

fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the

last fixture’s DMX output to a DMX terminator. Set 1st projector as the master and others are Slaves.

Start Addresses of all Slaves are 001; Operation mode of the Master can be set any mode for a Master’ and Slaves’ operation modecan

besetaccordingly.

AfterPoweredon,thegroup willruninMaster/SlaveMode

6. OPERATIONMENU

1st LEVEL

2ndLEVEL

3rdLEVEL

4thLEVEL

5thLEVEL

Address

DMXAddress

1-477

1-474

1-458

IP Address

DefaultIPAddress

2.X.X.X/10.X.X.X

CustomIPAddress

X.X.X.X

SubNetMask

X.X.X.X

ArtNet

ArtNetUniverse

0-255

Reset

Total Reset

ReallyReset?

Confirm/Cancel

Pan&TiltReset

ReallyReset?

Confirm/Cancel

ColourSystemReset

ReallyReset?

Confirm/Cancel

GoboReset

ReallyReset?

Confirm/Cancel

Zo.Fo.Fr.Pr.Reset

ReallyReset?

Confirm/Cancel

OtherReset

ReallyReset?

Confirm/Cancel

ConfigSettings

DMXChannelMode

ShortMode

StandardMode

ExtendedMode

ViewSelected Mode

Strobe

…..

SignalSelect

XLROnly

XLRFirst

WirelessOnly

WirelessFirst

WirelessIn/XLR Out

ArtnetOnly

ArtnetIn/XLROut

LossofDMX

Normaltimeout

Hold LastValue

DisplayConfig

DisplayMode

OffAfterDelay

OnAlways

DisplayInvert

InvertOFF

InvertON

InvertAuto

LanguageSetting

English

Chinese

TemperatureUnit

CelsiusDegree

Fahrenheit Degree

回路插

输入输出输入输出输入

主机从机从机

DMXTERMINATOR

MASTER

SLAVE

INPUT

OUTPUT

INPUT

OUTPUT

INPUT

DMXCONTROLLER

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PR Lighting DJ-Equipment Handbücher

PR Lighting

PR Lighting XLED 6019 Bedienungsanleitung

PR Lighting

PR Lighting XL 1200 Bedienungsanleitung

PR Lighting

PR Lighting StarBrite Bedienungsanleitung

PR Lighting

PR Lighting PILOT 300 Bedienungsanleitung

PR Lighting

PR Lighting LED STUDIO 3605 Bedienungsanleitung

PR Lighting

PR Lighting PR-8129 Bedienungsanleitung

PR Lighting

PR Lighting PR-2302 Bedienungsanleitung

PR Lighting

PR Lighting PR-8102 Bedienungsanleitung

PR Lighting

PR Lighting JNR BWS 350 Bedienungsanleitung

PR Lighting

PR Lighting ARC LED 3108 Bedienungsanleitung

PR Lighting

PR Lighting PR-8110 Bedienungsanleitung

PR Lighting

PR Lighting XPar 150 Bedienungsanleitung

PR Lighting

PR Lighting XR440 BEAM Bedienungsanleitung

PR Lighting

PR Lighting XR-230 BEAM Bedienungsanleitung

PR Lighting

PR Lighting XLED 3007 Bedienungsanleitung

PR Lighting

PR Lighting XLED 1037 Bedienungsanleitung

PR Lighting

PR Lighting XRLED 1200 SPOT Bedienungsanleitung

PR Lighting

PR Lighting XRLED 3000-W Framing Bedienungsanleitung

PR Lighting

PR Lighting XPar 348 Bedienungsanleitung

PR Lighting

PR Lighting Theatre Master PR-3010 Bedienungsanleitung

PR Lighting

PR Lighting JNR-8119A Bedienungsanleitung

PR Lighting

PR Lighting XR480S BWS Bedienungsanleitung

PR Lighting

PR Lighting AQUA 580 BEAM Bedienungsanleitung

PR Lighting

PR Lighting XR 380 Beam Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung