Precor 9.31 Bedienungsanleitung

9.31, 9.33, 9.35 Treadmill

Page 1

9.31, 9.33, 9.35 Treadmill

Warning: This service manual is for use by Precor trained service providers only.

IfyouarenotaPrecorTrainedServicer,youmustnotattempttoserviceanyPrecorProduct;

Call your dealer for service.

This document contains information required to perform the majority of troubleshooting, and

replacement procedures required to repair and maintain this product.

This document contains general product information, software diagnostic procedures (when

available), preventative maintenance procedures, inspection and adjustment procedures,

troubleshooting procedures, replacement procedures and electrical block and wiring diagrams.

To move directly to a procedure, click the appropriate procedure in the bookmark section to the

left of this page. You may “drag” the separator bar between this page and the bookmark section

to change the size of the page being viewed.

Unauthorized Reproduction and Distribution Prohibited By Law

20081-116

9.31, 9.33, 9.35 Treadmill

Page 2

Section One -

Things you Should Know

About This Appendix

Section One, Things You Should Know. This section includes technical specifications. Read

this section, as well as the 9.33 or 9.35 Treadmill Owner’s Manual, before you perform the

maintenance procedures in this manual.

Section Two, Software Features. Precor treadmills are programmed with several diagnostic

and setup features. This section contains the procedures you need to access the diagnostic

features on this treadmill.

Section Three, Checking Treadmill Operation. This section provides you with a quick way of

checking treadmill operation. Check treadmill operation at the end of a maintenance procedure

and when it is necessary to ensure that the treadmill is operating properly.

Section Four, Inspection and Adjustment Procedures. Perform inspection procedures when

a trouble symptom points to a particular problem and after removing and replacing major

components. Many maintenance problems can be fixed by adjusting various treadmill

components. This section also provides you with the step-by-step procedures required to make

these adjustments.

Section Five, Troubleshooting Procedures. The diagnostic and troubleshooting procedures

contained in this section should be performed when it is necessary to isolate a problem to a

particular component.

Section Six, Replacement Procedures. When a treadmill component must be replaced, go to

this section and follow the step-by-step procedures required to remove and replace the

component.

Section Seven, Technical Diagrams and Parts Lists. This section includes wiring diagrams,

and block diagrams for the 9.33 and 9.35 Treadmill.

General Information

For the latest exploded view diagram, part number and part pricing information, visit the Precor

dealer website at “www.precor.com/connection”.

9.31, 9.33, 9.35 Treadmill

Page 3

Procedure 2.1 - Accessing the Hardware Validation Program

The treadmill's diagnostic program consists of the following modes:

• Display Test

• Keyboard Test

• Heart Rate Test

• Machine Test

Procedure

1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker.

2. Refer to diagram 2.1 below and press keys RESET,5,1,7,6,5,7,6,1, sequentially. Use the

numeric keypad to enter the number sequence. The ARROW keys will step you through the

test modes listed above, allowing you to skip tests or perform only specific tests.

3. DISPLAY TEST.

4. Press the OK key to enter the display test. Press the OK or ENTER key several times to

step through all of the LED’s on the display. Ensure that all of the LED’s illuminate. Press

and hold the OK or ENTER key to exit the display test.

Diagram 2.1 - 9.33 Display

Numeric

Keypad

OK key

Arrow Keys

RESET key

9.31, 9.33, 9.35 Treadmill

Page 4

5. KEYBOARD TEST.

6. The keyboard test will place a dot on the display for each key on the display, including the

numeric keypad. Pressing a key will cause the dot associated with the key to go out. Test all

of the keys in this manner. Tug on the safety key lanyard, to ensure that the STOP key is

activated.

7. Press and hold the OK or ENTER key to exit the keyboard test.

8. HEART RATE TEST.

9. The heart rate test will display the heart rate being received during this test from the hand

held grips, chest strap transmitter or test transmitter.

10. The display will toggle between unfiltered and filtered heart rate readings. They will be

prefixed “U” for unfiltered, “F” for filtered. When a heart rate signal is being accepted the

“heart” will blink and the heart rate will be displayed in the heart rate window and the main

window. Test the heart rate in both the hand held and wireless (chest strap or test

transmitter) modes.

11. Press the OK or ENTER key to exit the heart rate test.

12. MACHINE TEST.

13. There are two test modes in the MACHINE TEST, they are BELT SPEED and INCLINE.

Use the ARROW keys to select the desired test.

14. BELT SPEED

15. Press the OK or ENTER key. POWERBITS will be momentarily displayed then the powerbit

number will be displayed. The power bit level can be checked by starting the running belt.

16. Press the OK key to exit the belt speed test.

17. INCLINE

18. Press the OK or ENTER key. A/D will be momentarily displayed then the analog to digital lift

position number will be displayed. The analog to digital lift position number represents the

incline’s physical position. The A/D number is used to calibrate the incline. The incline must

be calibrated when a new lift motor is installed.

19. Press the RESET to exit the MACHINE TEST.

9.31, 9.33, 9.35 Treadmill

Page 5

Procedure 2.2

- Accessing the Information Display Program

The information display will access the following data;

• Odometer

• Hour Meter

• U Boot SW

• U Base SW

• Lower SW

• Metrics Board SW

• Usage log

• Error log

Procedure

1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker.

2. Refer to diagram 2.1 above and press keys RESET,6,5 sequentially. Use the numeric

keypad to enter the number sequence. The ARROW keys will step you through the display

modes listed above, allowing you to skip displays or view only specific displays.

3. The display will momentarily read, DIAGS - INFORMATION DISPLAY.

4. ODOMETER

5. Press the OK or ENTER key. The treadmill’s odometer will be displayed as 1234567 MILES

or 1234567 KM.

Note: The odometer data is stored in non-volatile memory on the upper PCA. If the upper PCA

is replaced the odometer data will be lost.

6. Press the OK or ENTER key to exit the odometer display.

7. HOUR METER.

8. Press the OK or ENTER key. The operating time of the unit will be displayed as 12345

HOURS. The operating time is defined as total amount of time that the unit has operated in

program modes with the drive motor running. The hour meter is also used to provide the

“time stamp” for the error code log.

9. Press the OK or ENTER key to exit the hour meter display.

10. U BOOT SW

11. Press the OK or ENTER key. The U Boot SW part number will be displayed. The U Boot SW

is the software internally used to upload upper PCA operating system software (U Base

SW).

9.31, 9.33, 9.35 Treadmill

Page 6

12. Press the OK or ENTER key to exit the U Boot SW display

13. U BASE SW

14. Press the OK or ENTER key. The U Base SW part number will be displayed. The U Base

SW is the upper PCA operating system software.

15. Press the OK or ENTER key to exit the U Base SW display.

16. LOWER SW

17. Press the OK or ENTER key. The Lower SW part number will be displayed. The Lower SW

is the lower PCA operating system software.

18. Press the OK or ENTER key to exit the Lower SW display.

19. METRICS BOARD SW

20. Press the OK or ENTER key. The metrics board software part number will be displayed.

21. Press the OK or ENTER key to exit the metrics board SW display.

22. USAGE LOG

23. Press the OK or ENTER key. The usage for each program can be displayed. The ARROW

keys will allow to scroll through the list of programs. For example the manual program usage

will be displayed as MANUAL USED X TIMES TOTAL X MINUTES.

24. Press the OK or ENTER key to exit the usage log display.

25. ERROR LOG

26. Press the OK or ENTER key.

27. The error log will store up to 10 error conditions. The errors are logged with the most recent

error in position one. When a new error condition occurs, each existing error is pushed down

one position in log. If there was an error in position 10 when a new error was logged, the

error that was in position 10 will be lost.

28. Each error in the log will show the odometer reading (in miles) and the time (hour meter) and

motorcurrentreadingwhentheerroroccurred.Theerrorsaredisplayedas;

1 ER20 XXXXX MI XXX HRS. XX.X AMPS

29. The ARROW keys will allow you to scroll through the log.

30. When the QUICK START key is held for 2 seconds the message HOLD TO CLEAR

ERRORS will be displayed. If the QUICK START key is held for an additional 2 seconds, the

log will be cleared. The message NO ERRORS will be displayed and all error are erased

from the log.

9.31, 9.33, 9.35 Treadmill

Page 7

31. Press the RESET key to exit the information display.

32. Note: the error log can also be entered at any time by pressing and holding the RESET key

for four seconds.

9.31, 9.33, 9.35 Treadmill

Page 8

Procedure 2.3 - Accessing the User Parameter Program

This procedure allows you to change the following settings:

• Select Units (9.31, 9.33)

• Set Max Pause Time

• Set Cool Down Time

• Set Speed Limit

Procedure

1. Plug the power cord into the wall outlet, then turn on the treadmill with the circuit breaker.

2. Refer to diagram 2.1 above and press keys RESET,5,6,7,1 sequentially. Use the numeric

keypad to enter the number sequence. The ARROW keys will step you through the display

modes listed above, allowing you to skip displays or view only specific displays.

3. The display will momentarily display DIAGS - SET PARAMETERS

4. SELECT UNITS (9.31, 9.33)

5. The currently selected measurement unit will then be displayed.

6. Use the ARROW keys to toggle between U.S. and METRIC.

7. Press the ENTER key to select the currently displayed measurement unit.

Note: To change the measurements units on a 9.35, Press the METRICS key, select the

measurement unit with the ARROW keys and save the selection with the OK key.

8. SET MAX PAUSE TIME

9. Press the OK or ENTER key.

10. Use the ARROW keys to set the maximum pause time between 1 and 10 minutes.

11. Press the ENTER key to select the currently displayed pause time.

12. SET COOL DOWN TIME

13. Press the OK or ENTER key.

14. Use the ARROW keys to set the COOL DOWN time between 1 and 5 minutes.

15. Press the ENTER key to select the currently cool down time.

9.31, 9.33, 9.35 Treadmill

Page 9

16. SET SPEED LIMIT

17. Press the OK or ENTER key.

18. Use the ARROW keys to set the maximum speed between 1 and 12 MPH.

19. Press the ENTER key to select the currently displayed speed limit.

20. Press the RESET key to exit the set club parameters display.

9.31, 9.33, 9.35 Treadmill

Page 10

Procedure 2.4

- Documenting Software Problems

When a problem is found with the software in the upper or lower PCA, record the information

listed below.

When a problem occurs, record the following information:

• Model and serial number

• Software version number

• Program number running when the problem occurred

• A description of:

a. What happened or failed to happen.

b. The action taken by the user just before the problem occurred.

c. Problem-related information (such as how far into the program the problem occurred,

the work level being used when the problem occurred, etc.).

• The frequency of occurrence.

Andere Handbücher für 9.31

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Precor Tretmühle Handbücher

Precor

Precor C932i Bedienungsanleitung

Precor

Precor Experience Series 700 Line Bedienungsanleitung

Precor

Precor Treadmills 932i Betriebsanleitung

Precor

Precor 9.25 Bedienungsanleitung

Precor

Precor M9.5sp Bedienungsanleitung

Precor

Precor 9.21 Bedienungsanleitung

Precor

Precor M9.55 Bedienungsanleitung

Precor

Precor TRM 800 Montageanleitung

Precor

Precor TRM10/GEN06 Bedienungsanleitung

Precor

Precor C934 Bedienungsanleitung

Precor

Precor 9.23 Bedienungsanleitung

Precor

Precor Treadmill EFX534 Bedienungsanleitung

Precor

Precor C932 Bedienungsanleitung

Precor

Precor TRM 211 Technisches Handbuch

Precor

Precor TRM 885.v2 Bedienungsanleitung

Precor

Precor TRM. 600 Bedienungsanleitung

Precor

Precor M9.57 Bedienungsanleitung

Precor

Precor M9.45i Bedienungsanleitung

Precor

Precor TRM 800 Montageanleitung

Precor

Precor ENERGY SERIES Bedienungsanleitung

Precor

Precor 905e Bedienungsanleitung

Precor

Precor M9.21i Bedienungsanleitung

Precor

Precor C932i Bedienungsanleitung

Precor

Precor Experience Series 700 Line Bedienungsanleitung

Beliebte Tretmühle Handbücher anderer Marken

Treadly

Treadly TREADLY 2 Bedienungsanleitung

HEALTH ONE

HEALTH ONE Walk Ro Bedienungsanleitung

NordicTrack

NordicTrack NTL12941 Bedienungsanleitung

NordicTrack

NordicTrack T7.5 S Bedienungsanleitung

Gold's Gym

Gold's Gym ADVANTAGE GGTL12920 Bedienungsanleitung

Merax

Merax MS282992 Bedienungsanleitung

FYTTER

FYTTER RU-2SX Bedienungsanleitung

FitLogic

FitLogic freewill d225 Bedienungsanleitung

HOP-SPORT

HOP-SPORT ESTIMA HS-3200LB Bedienungsanleitung

Horizon Fitness

Horizon Fitness Adventure 5 Plus Bedienungsanleitung

Stamia

Stamia InMotion II Bedienungsanleitung

Smooth Fitness

Smooth Fitness EVO 3i Bedienungsanleitung

NordicTrack

NordicTrack NETL81810.0 Bedienungsanleitung

Schwinn

Schwinn 830/Journey 8.0 Bedienungsanleitung

Keys Fitness

Keys Fitness HealthTrainer HT-740T Bedienungsanleitung

Spirit

Spirit XT8 Bedienungsanleitung

NordicTrack

NordicTrack T 14.0 Treadmill Bedienungsanleitung

Master

Master F22 Bedienungsanleitung