Pro-Ject Audio Systems BOX-DESIGN Vinyl NRS Box S3 Bedienungsanleitung

INSTRUCTIONS FOR USE

Pro-Ject Vinyl NRS Box S3

Dear music lover,

thank you for purchasing this Pro-Ject Audio Systems´ product.

In order to achieve maximum performance and reliability you should study these instructions for use carefully.

Warning of a hazard for the user, the unit or possible misuse.

Important notice.

Safety instructions

AC outlet voltages vary from country to country. Before connecting to the mains, make sure that the

voltage in your area meets the voltage requirements printed on the power supply.

The power supply is used to connect/disconnect the unit from the mains. Make sure that the power supply

is easily accessible at all times. Never handle the device, the power supply while your hands are wet or

damp.

Avoid letting liquids enter the device or the power supply. Never place any item containing

liquid, such as a flower vase on or near the device. Never spill any liquid on the device or the power

supply. Never place any naked flame sources, such as lighted candles on or near the device. The product

shall not be used in damp or wet locations, next to a bathtub, sink, swimming pool or any other similar

conditions.

Connectors

Make all connections whilst the device is disconnected from the power supply.

Take care to connect the left and right channels correctly. The right channel is usually marked red, the

left channel black or white. Never use any other power supply than the one supplied with the unit!

Line In

Connect the output of the phono preamplifier to the RCA Line In.

Line Out

Connect the Line Out of your Vinyl NRS Box S3 to a line input of your preamplifier or integrated amplifier.

Mains power connection

Connect the low voltage plug from the power supply to the Power 18V DC socket of the amplifier before

connecting the power supply to the mains.

Front panel controls

To switch on from standby or to standby

The push button on the left side of the front panel turns the unit on or back into standby/bypass mode. The

blue LED beside the stand-by push button shows that the unit is switched on. It takes approximately 3 seconds

to activate the electronics until it goes into operational mode. If the unit is switched off, line in and line out

sockets are linked together and all the electronics are disconnected from the signal path – pure bypass mode

(galvanic bypass).

VNRS

VNRS stands for “Vinyl Noise Reduction System”. If the button is pressed, the system is activated and noise

from the played record is reduced. VNRS can reduce vinyl surface noise and turntable drive noise up to 6dB,

while played music stays practically untouched. The LED shows the on/off status of the VNRS.

De-Crackle

The De-Crackle function allows you to reduce crackling sounds coming from the record. You can adjust the

sensitivity of the algorithm by turning the potentiometer. Normal working position is in the center. If you turn it

fully counter-clockwise (left), the algorithm is switched off. (This position is usable if you are playing a perfectly

intact record and only want to use VNRS.)

If you are playing a slightly used or slightly damaged record, you must find the optimal position in which the

music stays untouched, but the crackling is reduced. Start in the center position. Detected crackle and clicks

are indicated by the red LED located right beside the De-Crackle control. If the LED blinks, crackling was

detected and reduced. Find the position in which crackling is reduced sufficiently, but the music stays

subjectively untouched (with no audible distortion). This position is usually +/-30 degrees left or right from the

center position.

The optimal position depends on the status of the used record, type of cartridge and type of phono preamplifier.

Optimal position can slightly vary from track to track on the record. In low level parts of the music and between

tracks, the De-Crackling system is more sensitive. In this situation, the crackle detection LED blinks more often.

If you want to compare the sound with and without this device, simply switch it OFF. The galvanic bypass takes

place, and you can directly compare it to the dry signal. After switching ON, it is necessary to wait about 3

seconds until the operation mode is active.

Intensity

The De-Crackle algorithm can be used in two intensity levels for reducing of detected crackling. If the Intensity

button is not pressed, the basic intensity level is used. If the Intensity button is pressed, the advanced level

(stronger) is used. The advanced level is more effective, but could affect the music. For most new or slightly

used records, the basic level should be fine. For used records, switch to advanced level. Try to fine tune De-

Crackle control individually. Listen in both positions and choose subjectively better one for each record. If

advanced intensity level is activated, indication LED lit.

-6dB

If the input level is too high, clipping can occur. In this case, the red clip LED located right beside the -6dB

switch blinks and indicates a system overload. In such a situation, please reduce the gain of your phono

preamplifier. If your preamplifier does not have a gain setting, press the -6dB button on your Vinyl NRS Box

S3. Clipping should no longer occur.

Note that this reduction does not affect the bypass mode! Bypass mode will be 6 dB louder than

operational (ON) mode in this case.

Technical specifications Pro-Ject Vinyl NRS Box S3

Internal sampling: 96 kHz/24 bits

Internal processing: 56-bit accumulator, double precision

Frequency response 20Hz to 20 kHz: -0,6 dB / +0,1dB

Frequency response 30Hz to 20 kHz: -0,2 dB / +0,1dB

Clip indication: -0,6 dB below real clipping

Bypass mode: galvanic linked together (Rlink<0,3 ohm)

THD: <0,009% (500 mVrms Input Level)

VNRS noise/rumble reduce: up to 8dB (20Hz to 20 kHz)

De-Click reduce (basic): 8 dB (3kHz to 20 kHz)

De-Click reduce (intensity): 12 dB (2kHz to 20 kHz)

Outboard power supply: 18V/500mA DC, suitable for your country's mains supply

Power consumption in standby: 0W OFF/Standby, 2.2W ON (without outboard power supply)

Dimensions: WxHxD (D with sockets): 103 x 37 x 104 (119) mm

Weight: 340 g without power supply

Service

Should you encounter a problem which you are not able to alleviate or identify despite the above information,

please contact your dealer for further advice. Only if the problem cannot be resolved there, the unit should be

sent to the responsible distributor in your country.

Warranty

The manufacturer accepts no responsibility for damage caused by not adhering to these instructions

for use. Modification or changes to any part of the product by unauthorized persons release the

manufacturer from any liability over and above the lawful rights of the customer.

Pro-Ject Audio Systems is a registered Trademark of

H. Lichtenegger.

This guide was produced by: Pro-Ject Audio Systems

The information was correct at the time of going to

press. The manufacturer reserves the right to make

changes to the technical specification without prior

notice as deemed necessary to uphold the ongoing

process of technical development.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Pro-Ject Audio Systems Verstärker Handbücher

Pro-Ject Audio Systems

Pro-Ject Audio Systems Head Box II Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Box S USB Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pre Box Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject Tube Box SE Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Amp Box Mono Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pre Box S Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject Head Box II Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Amp Box RS Mono Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject Phono Box S Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems CD Box Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Box-Design MaiA S3 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pre Box S2 Analogue Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems BOX-DESIGN Stereo Box DS2 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box II Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Amp Box DS2 Mono Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Phono Box USB V Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Stereo Box DS3 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject MaiA Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems MaiA Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pre Box DS2 Analogue Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Amp Box SE Mono Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Record Box E Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Head Box S Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Amp Box Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung