Pro-Ject Audio Systems 2 xperience sb s Bedienungsanleitung

INSTRUCTIONS FOR USE

Pro-Ject 2 Xperience SB S

Controls, features and connections

1 Motor transport foam inserts

2 Motor with motor pulley

3 Drive belt *

4 Sandwich platter *

5 Tonearm counterweight * 5a Downforce scale

6 Tonearm lift lever

7/17 Tonearm rest and removable transport lock

8 Tonearm tube 8a Tonearm base

9 Lid *

10 Lid hinges

11 Hinge fasteners

12 Power supply socket

13 Detachable headshell with fingerlift

14 Phono output sockets and earth connection

15 Anti-skating mechanism *

16 Anti-skating mechanism support

18 Adjustable tip-toe feet anti-scratch cups *

19 Speed control button

Connection cable (not shown) *

Screw-down record clamp (not shown) *

Universal power supply (not shown) *

Single adapter (not shown) *

Dear music lover,

Thank you for purchasing a Pro-Ject Audio Systems record player.

In order to achieve maximum performance and reliability, please study these instructions carefully.

Warning of a hazard for the user, the unit or possible misuse

Important notice

** The following instructions for adjusting the cartridge are provided in case the cartridge is replaced by a

different model at a later date.

During assembling and adjustment small parts could be lost if they are not carefully placed in a suitable

receptacle. Before starting assembly make yourself acquainted with the parts listed above which are

correspondingly numbered in the technical drawings above. Separately packed items are marked with an

asterisk *

Safety instructions

The power supply is used to connect and disconnect the unit from the mains. Make sure that the plug

is easily accessible at all times. Hold the plug when unplugging the power cord. Never handle the

power cord while your hands are wet or damp.

Avoid letting liquids enter the device. Never place any item containing liquid, like a flower vase, on

or near the device. Never spill any liquid on the device. Never place any naked flame sources, like

lighted candles, on or near the device. The product shall not be used in damp or wet locations, next to

a bathtub, sink, swimming pool or any other similar conditions.

Keep plastic bags away from children to prevent any risk of suffocation.

Set-up

The deck is supplied partially disassembled and carefully packed for a safe transport. Remove all parts from

the transport packaging carefully.

Screw the three tip-toe feet (18) onto the threaded bolts located on the underside of the plinth Make sure the

surface you wish to use the turntable on is levelled (use a spirit level) before placing the turntable on it.

Put the platter bearing housing carefully over the bearing axle. Put the record clamp on the platter and level

the plinth using the spirit level and the adjustable feet (18).

Fit the drive belt (3) around the platter (5) and the motor pulley (2).

Avoid getting sweat or grease on the belt as these will deteriorate the performance and reduce the belt's

lifespan. Use absorbent kitchen paper to remove any oil or grease from the outer edge of the hub and the belt.

Remove the transport lock (17) from the tonearm. Store it in the original packaging so they are available for

any future transportation.

Please note: We recommend to using the record player without a mat on the platter.

Cartridge downforce adjustment

The supplied counterweight (5) is suitable for cartridges weighing between 6 - 12g. An alternative counterweight

for cartridges weighing between 10 - 14g is available as accessory part. Adjust the downforce before installing

the anti-skating weight.

Following adjustments have to be done very carefully. Remove cartridge protection cap. Push and turn the

counterweight (5) carefully on the rear end of the tonearm tube (8), so that the downforce scale (5a) shows

towards the front of the player. Lower the armlift and position the cartridge in the space between arm rest and

platter. Rotate the counterweight (5) until the arm tube is balanced. The arm should return to the balanced

position if it is moved up or down.

Once the arm is balanced correctly return it to the rest. Hold the counterweight (5) without moving it and gently

revolve the downforce scale ring (5a) until the zero is in vertical position. Check whether the arm still balances

out.

Rotate the counterweight counter clockwise (seen from the front) to adjust the downforce according to the

cartridge manufacturer's recommendations. One mark on the scale represents 1 mN (= 0,1g / 0,1 Pond) of

downforce.

Anti-skating force adjustment

The anti-skating mechanism is shipped partially disassembled to avoid damage during transport. For correct

installation, please follow the steps below.

Step 1:

Prepare anti-skating sliding mechanism from the accessories bag.

The anti-skating sliding mechanism is supplied with a pre-mounted anti-skating weight and thread for

mounting on the tonearm.

Step 2:

Put the eye of the anti-skating thread around the hole for the HOOK SCREW and screw the HOOK SCREW

into the tonearm through the eye of the anti-skating thread as shown in the illustration below.

Step 3:

Put the anti-skating sliding mechanism on the end of the anti-skating support rod. The anti-skating thread

should fit into the groove in the tonearm.

Be careful when handing the anti-skating thread in order to avoid damaging it.

Step 4:

Anti-skating force adjustment:

Adjust the anti-skating force by positioning the weight on the appropriate groove of the anti-skating sliding

mechanism. Anti-skating downforce should be adjusted in correspondence with the tonearm downforce as

follows:

Tonearm downforce: Anti-skating groove:

Lower than 13 mN or 1.3 grams 1st groove from bearing

13–18 mN or 1.3–1.8 grams 2ndgroove from bearing

18–25 mN or 1.8–2.5 grams 3rd groove from bearing

Connection to the amplifier

The record player has gold plated female RCA phono sockets (14) so you can substitute the interconnect cables

supplied with higher quality cables such as the Pro-Ject Connect it interconnect cables for connection to the

amplifier if you wish. Use the Phono input (sometimes labelled gram, disc or RIAA) on your amplifier. Make

sure that the phono input offers correct matching and amplification for the type of cartridge used. Line inputs

(like CD, Tuner, Tape or Video) are not suitable.

Take care about connecting the left and right channel correctly. The right channel is usually marked red, the

left channel black or white. Check the manual of your amplifier for relevant information. An earthing wire

may be connected to the screw terminal between the sockets if you encounter humming problems.

If your amplifier does not have an input suitable for phono cartridges, a separate phono amplifier stage for

MM or MC cartridges is required. It has to be connected between record player and a free line level input of

the amplifier.

For detailed product information regarding Pro-Ject Audio Systems interconnect cables and phono amplifiers

please visit our website: www.project-audio.com

Mains power connection

A universal power supply with 3 exchangeable sockets adapters suitable for all countries is supplied. Select

the correct adapter for your country and insert the adapter to the exchangeable part of the power supply.

Connect the low voltage plug from the power supply to the socket (12) on the rear side of the record player

before connecting the power supply to the mains.

Fitting the lid

Fit the lid (dust cover 9) carefully over the hinge prongs and adjust the screws (11) until the lid stays open

where you want it to without being too stiff to open or close.

Switching on and off

Press the speed control button START (19) for starting the turntable. To change the speed from 33 r.p.m. to

45 r.p.m., press the START (19) button again. Speed is correct, when the LED diode stops blinking. To switch

the turntable into STAND BY mode, hold the button START (19) for 3 seconds.

For detailed product information please refer to the Pro-Ject web site www.project-audio.com.

Useful tips

The lid is not only a dust cover but also a resonant structure likely to be excited by acoustic energy

emanating from your loudspeakers during replay. The lid will pass this ambient sound into the plinth.

Therefore it is recommended to remove the lid during playback for achieving a better sound quality.

The record player should be positioned on a low-resonance surface such as wood or multiple layer ply board

to avoid structural vibrations disturbing replay.

Adjusting the vertical tracking angle (vta)

Put a record on the platter. When the needle is lowered into the record groove and the tonearm is not resting on

the lift arm, the tube of the tonearm should be parallel to the surface of the record.

If it is not, loosen both hexagon screws in the tonearm base just enough to allow vertical movement of the

arm pillar without force and slide the arm up or down until it is parallel.

Retighten the hexagon screws without applying excessive force (which would deform the arm pillar) –finger

tight is quite sufficient.

Adjusting the azimuth

The cartridge needle must be vertical in the record groove in

order to trace the groove wall modulations correctly.

A small screw at the bearing end of the arm allows incorrect

azimuth to be corrected.

Slacken off the screw just enough to be able to revolve the

arm tube without applying force. Note! Do not remove this

screw completely!

With the aid of a good magnifying glass adjust the needle until it is vertical in the groove (i.e. perpendicular

to the record's surface). Ideally this should correspond to the top surface of the cartridge body being parallel

to the record surface.

When the needle is vertical, retighten the screw carefully.

Please note: Under no circumstances should the arm tube be adjusted with the needle still in the

record groove! Irreparable damage may be caused to the cantilever suspension! The arm must be

lifted to make each adjustment and lowered afterwards to check it.

Mounting and connecting the cartridge

All cartridges with half inch mounting holes can be mounted. Leave the needle's protection cover on, fit the

cartridge to the headshell by using the supplied screws by passing one screw through each slot in the

headshell (12). Do not tighten the nuts yet.

Connect the tonearm wires with the cartridge pins as follows:

white left channel positive (L+)

red right channel positive (R+)

green right channel return (R -)

blue left channel return (L -)

The full sound quality of the record player can only be achieved if the cartridge is adjusted correctly. Particular

tools like the Pro-Ject Audio Systems alignment tool are required to accomplish this job properly. If you are not

well acquainted with the adjustment of cartridges, please call for the willing help of your Pro-Ject Audio Systems

dealer.

Please note: adjusting a cartridge and tonearm calls for the greatest care in order to avoid damaging

the cartridge or tonearm bearings. Ask your local dealer for help if you are unsure in any of the

necessary steps and precautions which must be taken.

Maintenance and cleaning

Your record player requires little or no regular maintenance. Remove dust with a slightly moistened antistatic

cloth. Never use a dry cloth because this will create static electricity which attract more dust! Antistatic

cleaning fluids are available at specialist stores but must be applied sparingly to avoid damage to rubber

parts. It is recommended to fit the needle cover before cleaning or maintenance is carried out to avoid damage.

If the player is not used over a long period of time the drive belt can be removed to prevent unequal stretching.

Always disconnect the record player from the mains power supply as a precaution before maintenance!

Technical specifications PRO-JECT 2 Xperience SB S/ Pro-Ject 9’’ S-tonearm

Nominal speeds

33/45 r.p.m.

Speed variance

±0,15 %

Wow and flutter

±0,09 %

Signal to noise

70dB

Effective tonearm mass

15g

Effective tonearm length

9 " (230mm)

Overhang

18mm

Power consumption

4W/ >0,5W standby mode

Outboard power supply

15V DC / 800m A, 90-264V AC, 47 –63Hz

Dimensions (W x H x D)

460 x 145 x 360mm, dust cover open 460 x 400 x 445mm

Weight

8,5 kg

Potential incorrect use and fault conditions

Pro-Ject Audio Systems turntables are manufactured to the highest standards and undergo strict quality

controls before leaving the factory. Faults that may possibly occur are not necessarily due to material or

production faults but can sometimes be caused by incorrect use or unfortunate circumstances. Therefore the

following list of common fault symptoms is included.

The platter does not turn although the unit is switched on:

The unit is not connected to the mains power supply.

No mains at the socket.

Drive belt is not fitted or has slipped off.

No signal through one or other channel or both channels:

No signal contact from the cartridge to the internal tonearm wiring or from that to the arm lead or

from that to the phono box or between that and the amplifier. This could be due to a faulty plug,

broken wire or solder joint or simply loose plug/socket connection.

Phono input not selected at amplifier.

Amplifier not switched on.

Amplifier or speakers defective or muted.

No connection to the loudspeakers.

Strong hum on phono input:

No earth connection from cartridge or arm or arm cable to amplifier, or earth loop.

Distorted or inconsistent sound from one or both channels:

Record player is connected to wrong input of amplifier, or MM/MC switch incorrectly set.

Needle or cantilever damaged.

Wrong r.p.m., drive belt overstretched or dirty, platter bearing without oil, dirty or damaged.

Service

Should you encounter a problem which you are not able to alleviate or identify despite the above information,

please contact your dealer for further advice. Only if the problem cannot be solved there the unit should be

sent to the responsible distributor in your country.

Guarantee repairs will be accepted only if the unit is returned correctly packed in the original package. Therefore

we strongly recommend keeping the original packaging.

Never return a record player without making sure that it is safely disassembled and correctly packed in the

original packaging according to the diagrams on the last page of this user guide. Please remove the following

parts from the turntable and pack them separately: power supply socket (12), counterweight (5), anti-skating

mechanism (14) platter (4) and belt (3). Mount the cartridge protection cap. Insert the transport lock for the

tonearm (17).

Warranty

The manufacturer accepts no responsibility for damage caused by not adhering to these instructions

for use and/or by transportation without the original packaging. Modification or change to any part

of the product by unauthorized persons releases the manufacturer from any liability over and above

the lawful rights of the customer.

Pro-Ject Audio Systems is a Registered Trademark of

H. Lichtenegger.

This guide was produced by: Pro-Ject Audio Systems

The information was correct at the time of going to

press. The manufacturer reserves the right to make

changes to the technical specification without prior

notice as deemed necessary to uphold the ongoing

process of technical development.

Inhaltsverzeichnis

Andere Pro-Ject Audio Systems Drehscheibe Handbücher

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject RPM 3 Carbon Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems VC-S2 ALU Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems 1 Xpression Carbon Classic Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Xtension 12 Evolution Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems X8 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut PRO Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems X1 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems A2 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Speed Box MK II Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems VC-S Firmware-Update

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut Carbon EVO Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject RPM 9.1 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Essential II Demon Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject 6 PerspeX Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut S Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut Carbon EVO Betriebsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems 2 Xperience Basic + Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut Carbon EVO Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Elemental Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject RPM 1.3 Genie Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject RPM 3 Carbon Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Signature 12 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Remote Box S2 Bedienungsanleitung

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut Carbon DC Esprit SB Bedienungsanleitung

Beliebte Drehscheibe Handbücher anderer Marken

Gemini

Gemini CDT-05 MKII Bedienungsanleitung

Rotel

Rotel RP-820 Bedienungsanleitung

Shuman

Shuman MC-250BT Bedienungsanleitung

Stanton

Stanton STR8-150 Bedienungsanleitung

Audio Technica

Audio Technica AT-LPW40WN Bedienungsanleitung

Crosley

Crosley McQueen CR7011-GY Bedienungsanleitung

Reloop

Reloop SMP-1 Bedienungsanleitung

auna

auna TT-Classic Plus Bedienungsanleitung

COMO AUDIO

COMO AUDIO Turntable Analog Bedienungsanleitung

Dual

Dual 1009 F Bedienungsanleitung

REED

REED Muse3C Bedienungsanleitung

AXIOMTEK

AXIOMTEK OPS883-H Series Bedienungsanleitung

Pioneer

Pioneer PL-71 Bedienungsanleitung

Vestax

Vestax PDX-a1 Bedienungsanleitung

Denon

Denon DP-400 Bedienungsanleitung

Dual

Dual 504 Bedienungsanleitung

Audio-Techica

Audio-Techica AT-LP60XBT Bedienungsanleitung

Goldring

Goldring G99 Bedienungsanleitung