Pro Scio X-1.6 Bedienungsanleitung
ENGLISH
PRO SCIO
X-1.6 & W-2.1
Jet12_15.indd 1 10/11/07 6:47:47 P
2
english
WARNINGS & CAUTIONS 4
COMPONENTS OF THE CYCLECOMPUTER 5
REPLACING THE BATTERY 6
CHANGING THE BATTERY IN THE WIRELESS
SPEED TRANSMITTER 7
INSTALLING THE CYCLOCOMUTER ON YOUR BIKE 8-12
KEYS & THEIR FUNCTIONS 13
MAIN OPERATING MODES 14-15
MEASURING WHEEL SIZE 16-17
PROGRAMMING THE CYCLOCOMPUTER
SELECTING MILES OR KILOMETERS 18
SETTING WHEEL SIZE 19
SETTING ODOMETER 20
SETTING TIME OF DAY 21
SETTING DISTANCE COUNTDOWN 22
SETTING CALORIES INFORMATION 23
TABLE OF CONTENTS
1
2_15.indd 2 10/11/07 6:47:47 PM
3
english
TABLE OF CONTENTS
OPERATING THE CYCLOCOMPUTER
SLEEP MODE 24
RESETTING THE UNIT 24
SELECT BIKE 1 OR BIKE 2 25
DISTANCE TRAVELED / DISTANCE COUNTDOWN 26
OPERATING THE STOPWATCH 27
CENTERLINE SEGMENT DISPLAY 28
TROUBLESHOOTING 29
FUNCTIONAL SPECIFICATIONS & RANGES 30
WARRANTY & CONTACT 31
Jet12_15.indd 3 10/11/07 6:47:47 P
4
english
WARNINGS & CAUTIONS
s 7!2.).' Failure to pay attention to the road, trail, traffic or your surroundings
could result in an accident, with risk of serious injury, paralysis or death. You must
focus on riding, not your computer. Learn computer operations, and do all possible
computer operations when not riding. For any operations you choose to perform while
riding, choose a time and place where this distraction has less risk.
s #!54)/. Mount the Cyclecomputer according to the directions in this instruction
manual.
s #!54)/. Avoid direct impact to the Cyclecomputer unit.
s #!54)/. Do not submerge the Cyclecomputer unit.
s #!54)/.Avoid using the Cyclecomputer unit in or near strong electromagnetic fields
such as high-voltage power lines or other transmitters.
s #!54)/. Do not disassemble the unit.
s #!54)/.Make sure the magnet and the transmitter are well aligned and check them
regularly.
s #!54)/.PRO Scio Cyclecomputers are intended for use on bicycles only and should
not be used on any motorized vehicle.
s #!54)/. Change the battery prior to failure to avoid data loss.
s #!54)/. Clean the unit with a mild detergent and a soft dry cloth. Never use any
kind of solvent or alcohol.
1
2_15.indd 4 10/11/07 6:47:48 PM
5
english
COMPONENTS OF THE CYCLECOMPUTER
#9#,/#/-054%25.)4
7)2%,%33&/2+42!.3-)44%2
(SCIO W-2.1 ONLY)
7(%%,-!'.%4
:)04)%3
7)2%,%33&/2+42!.3-)44%2
-/5.4).'0!$
(SCIO W-2.1 ONLY)
7)2%,%33-/5.4).'
"2!#+%4
(SCIO W-2.1 ONLY)
-/5.4).'"2!#+%425""%2
0!$
7)2%$42!.3-)44%2
-/5.4).'"2!#+%4
(SCIO X-1.6 ONLY)
1
2
3
4
7
6
5
8
Jet12_15.indd 5 10/11/07 6:47:49 P
6
english
REPLACING THE BATTERY
PRO Scio Cyclecomputers are powered by a CR2032 3v Lithium Battery. Under normal condi-
tions, this battery should last approximately one year.
REPLACING THE COMPUTER BATTERY
Using a coin, turn the battery door counter clockwise until the
door comes free.
2. Take care not to damage the O-ring seal for the battery com-
partment and carefully remove the old battery.
3. Place a new battery in the battery compartment with the posi-
tive (+) side toward the battery door. Be extremely careful not
to bend the battery contact when inserting a new battery.
4. Place the battery door over the opening and tighten it down by using a coin and turn-
ing in a clockwise direction.
5. If the O-ring has been damaged, replace it before reinstalling the battery door.
#!54)/.Extreme care should be taken when replacing the battery to ensure the unit
remains fully water resistant. Failure to properly replace the battery and correctly seal the
unit may cause the unit to become damaged and may void the warranty.
1
2_15.indd 6 10/11/07 6:47:51 PM
7
english
CHANGING THE BATTERY IN THE WIRELESS
SPEED TRANSMITTER
The Wireless Speed Transmitter uses a 23A 12v Alkaline battery.
Under normal conditions, this battery should last approximately
one year.
1. Using a coin, turn the battery door counter clockwise until the
door comes free.
2. Take care not to damage the O-ring seal for the battery
compartment and carefully remove the old battery.
3. Place a new battery in the transmitter positive (+) side toward
the battery door.
4. Place the battery door over the opening and tighten it down
by using a coin and turning in a clockwise direction.
5. If the O-ring has been damaged, replace it before reinstalling
the battery door.
./4%Extreme care should be taken when replacing the battery to
ensure the unit remains fully water resistant. Failure to properly
replace the battery and correctly seal the unit may cause the unit to
become damaged and may void the warranty.
Jet12_15.indd 7 10/11/07 6:47:51 P
8
english
INSTALLING THE WIRED CYCLECOMPUTER ON YOUR
BIKE - PRO SCIO X-1.6
INSTALLING WIRED FRONT WHEEL SPEED SENSOR
AND BRACKET
The PRO Scio X-1.6 uses a single wired sensor attached to the front fork.
1. Attach the front wheel sensor to either fork blade using the zip-ties
provided. Snug up the zip-ties but do not fully tighten them.
2. Attach the spoke magnet to a spoke on the same side of the wheel
as the sensor. Tighten the attachment screw just enough to hold the
magnet in place but loose enough so that it is still movable.
3. Adjust the position of the sensor and magnet so they are in proper
alignment as shown in the drawing and tighten the zip-ties and
magnet.
./4% The magnet should pass 1-3mm away from the sensor. The closer
you can get the magnet to the sensor the better.
1
2_15.indd 8 10/11/07 6:47:52 PM
9
english
INSTALLING THE WIRED CYCLECOMPUTER ON YOUR
BIKE - PRO SCIO X-1.6
INSTALLING WIRED FRONT WHEEL SPEED SENSOR AND BRACKET
(continued)
4. Route the remaining wire and bracket up the fork securing it with tape. Excess wire
should be wrapped around the brake cable housing until there is just enough slack
remaining to allow the bracket to be attached to the handlebars. Attach the bracket
to the handlebars and tighten the zip-ties.
#!54)/.When installing the system on a bicycle with front suspension, be sure to leave
enough slack for the action of the fork.
MOUNTING THE HANDLEBAR/STEM BRACKET
Place the Cyclecomputer unit into the mounting bracket and turn clockwise until the
unit snaps into place.
./4%When mounting the unit on the stem, you must first remove the
4 screws on the back of the mounting bracket and rotate it 90 degees.
Replace the screws - do not overtighten. The unit is now properly aligned
for mounting on the stem.
2. Place the mounting brakcet in the desired position on handle bars or
stem.
3. Thread the zip-ties provided through the holes on one side of the
mounting sleeve and around the handlebar or stem. Once the unit is
positioned correctly, secure the zip-ties and trim off the excess ends.
Jet12_15.indd 9 10/11/07 6:47:54 P
10
english
INSTALLING THE WIRELESS CYCLECOMPUTER ON
YOUR BIKE - PRO SCIO W-2.1
INSTALLING THE WIRELESS FORK TRANSMITTER
The PRO Scio W-2.1 receives speed and distance from a wireless transmitter mounted to
the front fork.
1. Attach the wireless front wheel sensor and rubber mounting
pad to the front of the left fork blade using the zip-ties
provided so the battery cap is pointing downward. Snug up
the zip-ties but do not fully tighten them. The sensor should
be mounted as high on the fork blade as possible. The range
of the transmitter is approximately 18in (46cm). Mounting
it high on the fork will assure good signal reception. Other
mounting locations may work, but we feel this is the best
location for most applications.
2. Attach the spoke magnet to a spoke on the same side of
the wheel as the sensor. Tighten the attachment screw just
enough to hold the magnet in place but loose enough so that
it is still movable.
1
2_15.indd 10 10/11/07 6:47:54 PM
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Pro Fahrradzubehör Handbücher
Beliebte Fahrradzubehör Handbücher anderer Marken
Sigma
Sigma BC 16.16 Bedienungsanleitung
Playcore
Playcore Dero Setbacks Bedienungsanleitung
VDO Cyclecomputing
VDO Cyclecomputing x3dw Bedienungsanleitung
Cateye
Cateye RAPID X2 Bedienungsanleitung
buratti meccanica
buratti meccanica Clorofilla Trail Bedienungsanleitung
Shimano
Shimano SG-8R20 Betriebsanleitung
