Proline TFP120A Bedienungsanleitung
FRIDGE-FREEZER
USER’S MANUAL
TFP120A
PLEASE READ THIS USER’S OPERATION MANUAL CAREFULLY BEFORE USING
1
NAMES OF PARTS
Note: Compartment design may change due to product improvement, No prior notice will
be given.
Freezer
compartment
Thermostat and
lamp assembly
Glass shelves
Freezer
d
oor
Fridge door
gas et
Door rac s
Leveling feet
2
THANK YOU FOR PURCHASING THIS PROLINE PRODUCT
This booklet contains the information you will require to install and operate your new
appliance.
It is important and worthwhile spending time to fully read this booklet so you will
understand how to operate the appliance safely and efficiently.
Please keep this booklet in a safe place so that you can refer to it when required.
Safety information
This information is provided in the interest of your safety. Please read the following
carefully before carrying out the installation or use of the appliance.
If you are discarding an old freezer or refrigerator with a lock / catch fitted to the
door ensure that it is left in a disabled condition to prevent the entrapment of young
children when playing.
As old refrigeration equipment may contain CFC’s which will damage the ozone
layer when disposing of any refrigeration equipment please contact your local waste
disposal department for advice on the correct method of disposal.
This appliance must only be used for its intended purpose i.e. the storage of
domestic edible foodstuffs and should not be used for any other purpose
Installation
Position the appliance and allow to stand for two to three hours before it is turned on
for the first time to allow the system to settle. Do not position next to any heat source
e.g. cooker boiler or in direct sunlight etc.
A clearance of 10 cm must be left between the sides of the appliance and any
adjacent cabinets or walls to allow for adequate air circulation. The appliance is not
designed for recessed installation (“building in”).
Install on a good firm level surface and any unevenness of the floor should be
corrected prior to installation slight unevenness can be overcome by adjusting the
front feet.
NOTE: If the appliance is positioned on a carpet soft floor covering you should
readjust the front feet once the appliance has had time to settle.
3
IMPORTANT SAFETY INFORMATION
Make sure the voltage marked on the rating plate matches the supply in your area.
The rating plate is located on the base of this appliance. Failure to use the correct
voltage will render the guarantee VOI and may damage the appliance.
This appliance is intended for domestic use only, any other use may invalidate the
warranty and might be dangerous.
This appliance is intended for indoor use only, do not use outdoors.
Accessible surfaces may get hot during operation, use handles and knobs at all times.
To protect against electric shock do not immerse cord, plugs, or appliance in water or
other liquid.
o not remove the plug by pulling on the mains cord, grasp the plug to remove it from
the wall outlet.
Unplug from outlet when not in use and before cleaning. Remove food before cleaning
the appliance.
If the mains lead becomes damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified person with a lead of the same type and rating to
avoid a hazard.
o not operate the appliance with a damaged cord or plug or after the appliance
malfunctions or has been damaged in any way. Consult the retail store where you
bought the appliance for advice.
o not insert over sized food as this could cause incorrect operation.
o not let cord hang over edge of the surface, or touch hot surfaces.
o not place appliance on or near hot surfaces, or in direct sunlight.
Extreme caution must be used when moving an appliance.
Always attach a plug to the mains cord, then plug into the wall outlet. To turn the
appliance off, turn the thermostat knob fully anticlockwise to setting 0, then remove
the plug from wall outlet.
A short power-supply cord is provided to reduce the risk of a tripping hazard.
The plug shall be the main disconnection device and will remain operable at all times.
This appliance is not intended for use by persons(including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play on the appliance or
swing on the door.
4
ELECTRICAL CONNECTION (UK ONLY)
For your safety please read the following information.
Warning: This appliance must e earthed.
The appliance must be connected to a 220 - 240 volts 50 cycle A supply by means of a
three pin socket, suitably earthed and should be protected by a 13 amp fuse in the plug.
The appliance is supplied with a standard 13 amp 3-pin plug fitted with a 13-amp fuse.
Should the fuse require replacement, it must be replaced with a fuse rated at 13 amp and
approved to BS1362.
If the mains plug is unsuitable for the socket outlet in your home or is removed for any
other reason, then the cut off plug should be disposed of safely, do not insert the cut off
plug into a mains outlet to prevent the hazard of electric shock. Remove the fuse before
disposal.
There is a danger of electric shock if the cut off plug is inserted into any 13-amp socket
outlet.
How to wire a 13 amp plug:
Important
The wires in the mains lead on this appliance are colored in accordance with the following
code:
Green and Yellow - Earth
Blue – Neutral
Brown – Live
As the colours may not correspond with the markings identifying the terminals in your plug
proceed as follows.
The green and yellow wire must be connected to the terminal in the plug which is marked
with the letter E or with the earth symbol or colored green and yellow.
The blue wire must be connected to the terminal marked N.
The brown wire must be connected to the terminal marked L.
You must make sure the mains cord is firmly secured under the cord clamp.
Warnings:
Keep ventilation openings, in the appliance enclosure or in the uilt in structure,
clear of o structions.
Do not use mechanical devices or other means to accelerate the defrost process,
other than those recommended y the manufacturer.
Do not damage the refrigerant circuit.
Do not use electrical devices inside the food storage compartments of the appliance,
unless they are of the type recommended y the manufacturer.
5
Instructions for use
Remove all packing materials and wash the interior of the appliance using
lukewarm water containing a little bicarbonate of soda in the proportion of 1
teaspoon to 1.2 liters (2 pints) of water. Do not use detergents or soaps as they
may taint the food. fter cleaning, dry all parts thoroughly.
Temperature Control
The refrigerator is designed to maintain an internal storage temperature in the
refrigerator compartment between to 0℃+ 10℃.
To enable adjustment of the temperature in the appliance it is fitted with an
adjustable thermostat located in the fridge compartment, which can be adjusted
from setting 1 (warmest) to 7 (coldest). For normal working temperature it is
recommended to adjust the thermostat control to the position 4.5, after a few
hours readjust the thermostat to the desired temperature. There is also an off
position “0”, which turns OFF the refrigerator and freezer compartments. Please
Note this dose not disconnect the appliance from the mains supply. To do this
you must remove the mains plug from the socket.
To obtain a lower internal temperature turn the thermostat temperature control
to a higher number. To obtain a higher internal temperature turn the thermostat
control to a lower number. However, the internal temperature and temperature
control setting is dependent on a number of factors:
1. Varying ambient temperatures.
2. The number of times the appliance doors are opened and how long the doors
remain open.
3. The amount and temperature of the food and drink introduced into the
appliance.
4. The weather conditions and time of year e.g. summer / winter.
5. The positioning of the appliance and an adequate air circulation to the sides
and back of the cabinet.
Never place hot or warm foods into the cabinet or leave the doors open for
longer than necessary as this will raise the temperature and cause excessive
amount of moisture thus increasing the amount of ice in the refrigerator / freezer
compartments.
The Internal Light
The internal light will automatically switch ON and OFF whenever the
refrigerator door is opened or closed. To change the light bulb, please see the
chapter on changing the light bulb.
6
Storage of fresh food in the refrigerator
Food should always be covered tightly with foil, plastic film, placed in bags or
stored in airtight containers. This will prevent food from dehydrating and prevent
the strong smell of some foods transferring to milder ones.
To store raw meat wrap in polythene bags or airtight containers and place on
the lowest shelf.
Do not allow raw meat to come into contact with cooked foods. For safety, only
store raw meat for two or three days. Fruit and vegetables should be thoroughly
cleaned and placed in the crisper drawer.
Milk and other liquids should be sealed with lids and placed in the bottle shelf
on the door.
Store frozen food
hen using the freezer for the first time or after defrosting, turn the thermostat
temperature control to setting 7 for at least two hours before introducing the
food to be stored, then adjust to your preferred setting.
All frozen food products you purchase should be placed in the freezer as soon
as possible to avoid the frozen food from defrosting.
Storage recommendations printed on the packaging of frozen food by the
manufactures should always be followed.
Freezing fresh food (Freezer)
Ensure that your freezing operations are carried out under the most hygienic
conditions, as freezing alone does not sterilise the food. Never put hot or even
warm foodstuffs into the freezer. Prior to storing the food, pack it in plastic bags,
aluminum foil or freezer containers and place into the freezer without putting
them in contact with food that has already been frozen.
See the technical data sheet at the rear of this booklet for the maximum
permissible amount in kilograms of fresh food that can be frozen in any 24-hour
period with a room temperature of 25℃. Never freeze more than the maximum
permissible.
Making ice cubes (Ice tray not supplied )
Pour water into the ice cube tray until it is two thirds full and place into the
freezer. Ice cubes will form in approximately 2 to 3 hours. The ice cubes can be
easily removed by twisting the ice cube tray or running under cold water for a
short time.
7
Refrigerator defrost process
The refrigerator defrosting process is carried out automatically every time the
compressor stops.
The defrost water drains from the cabinet into a tray placed on the top of the
compressor to the rear of the unit where it evaporates.
Freezer defrost process
Small amounts of frost will accumulate inside the freezer depending upon the
length of time during which the door is left open or the amount of moisture
introduced.
It is essential to ensure that no frost or ice is allowed to form at places where it
will affect the close fitting of the door seal. This might allow air to penetrate the
cabinet, thus encouraging continuous running of the compressor.
Thin frost formation is quite soft and can be removed with a brush or plastic
scraper. Do not use metal or sharp scrapers, mechanical devices or other
means to accelerate the defrosting process. emove all dislodged frost from the
cabinet floor.
For the removal of thin frost it is not necessary to switch off the appliance.
For the removal of heavy ice deposits disconnect the appliance from the mains
supply and empty the contents into cardboard boxes and wrap in thick blankets
or layers of paper to keep them cold. Defrosting will be most effective if carried
out when the freezer is empty, and it should be carried out as quickly as
possible.
An increase in temperature of frozen food packages during defrosting will
shorten the storage life. Provided that the contents are well wrapped and placed
in a cool area, they should keep for several hours.
Examine the contents when replacing them in the freezer and if some of the
packages have thawed out it should be eaten within 24hours or be cooked and
refrozen.
After defrosting has finished clean the inside with a solution of warm water with
a little bicarbonate of soda and then dry thoroughly. Wash all removable parts in
the same way and reassemble.
econnect the appliance to the mains supply and leave for 2 to 3 hours on
setting number 7 before introducing the food back into the freezer and setting
the thermostat to your normal setting.
8
Reversing The Doors
Before you reverse the refrigerator doors, you should ensure the refrigerator is unplugged
and empty and have someone to help you. You will need a cross head screwdriver and
adjustable spanner.
Remove the four retaining screws
on the rear and top of the top
cover, then remove the top cover.
Remove the retaining screws and
the top hinge, then remove the
upper door and put it in a safe place.
hile supporting the lower door,
remove the central hinge by
removing the two screws.
Remove the lower door from the
lower hinge pin. Tilt the fridge
backwards and rest it on a firm
surface.
Remove the lower hinge by
removing the screws. Re-fit the
adjustable foot from left side to
right side.
Remove the lower hinge pin using a
spanner. Turn the hinge over and replace
the hinge pin in the same hole.
(Reversed)Replace the lower hinge on the
other side and then stand the refrigerator
upright.
9
Remove and re-fit the blanking plugs on
the middle steel plate from right side to left
side. Remove the door hinge cap in the top
of the freezer door and insert it on the
opposite side of the door.
Replace the central hinge after
refitting the lower door, to assist
final adjustment, do not fully
tighten the hinge screws.
Unscrew the hinge pin from the
top hinge using the spanner.
Turn the hinge over and replace
it in the same slot. (Reversed)
Re-fit the top hinge while refitting
the upper door. Do not fully tighten
the screws.
Check that doors are aligned horizontally
and vertically and that all seals make good
contact with the cavity all the way around
the cavity opening before finally tightening
the hinges. Re-fit the plastic insert on the top
cover from left side to right side before
re-fitting the top cover. Re-adjust the
leveling feet, if necessary.
Inhaltsverzeichnis
Andere Proline Kühlschrank Handbücher
Proline
Proline PLF225A-U Bedienungsanleitung
Proline
Proline PCI223-F1-LED Bedienungsanleitung
Proline
Proline TFP135B Bedienungsanleitung
Proline
Proline PF200W Bedienungsanleitung
Proline
Proline TTR200DP Bedienungsanleitung
Proline
Proline TTR 60WP Bedienungsanleitung
Proline
Proline PLC2300WH Bedienungsanleitung
Proline
Proline PL115ABB Bedienungsanleitung
Proline
Proline PLF220A Bedienungsanleitung
Proline
Proline PLC253NFWH Bedienungsanleitung
Proline
Proline PRI122-F-4F Bedienungsanleitung
Proline
Proline PLC246WDSL Bedienungsanleitung
Proline
Proline BRF 44 Bedienungsanleitung
Proline
Proline UFZ171 Bedienungsanleitung
Proline
Proline PMF70A Bedienungsanleitung
Proline
Proline DD208WH Bedienungsanleitung
Proline
Proline UFZ167 Bedienungsanleitung
Proline
Proline PLF238L Bedienungsanleitung
Proline
Proline PLC 241 Bedienungsanleitung
Proline
Proline PLC265WH Bedienungsanleitung
Beliebte Kühlschrank Handbücher anderer Marken
Bonnet Neve
Bonnet Neve SKYVIEW PLUS Bedienungsanleitung
Zanussi Electrolux
Zanussi Electrolux ZERB 8441 Bedienungsanleitung
Sharp
Sharp SJ-BA31IEXW2-EU Bedienungsanleitung
CORBERO
CORBERO CC2300MCW Bedienungsanleitung
KitchenAid
KitchenAid 2205264 Bedienungsanleitung
Stengel
Stengel KU 1101 A++ Bedienungsanleitung
