Proline TFP93AW Bedienungsanleitung

Under Counter Fridge-Freezer

TFP93AW

MODEL: TFP93ASL

INSTRUCTION MANUAL

General Description of Fridge-Freezer

1. Top Cover

2. Thermostat and lamp assembly

3. Glass Shelf

4. Crisper Cover

5. Crisper

6. Levelling Feet

7. Door Shelves

8. Freezer Door Gasket

Note: Compartment design may change due to product improvement,

NO prior notice will be given.

THANK YOU FOR PURCHASING THIS PROLINE PRODUCT

This booklet contains the information you will require to install and operate your new

appliance.

It is important and worthwhile spending time to fully read this booklet so you will

understand how to operate the appliance safely and efficiently.

Please keep this booklet in a safe place so that you can refer to it when required.

ELECTRICAL CONNECTION (UK ONLY)

For your safety please read the following information.

Warning: This appliance must be earthed.

The appliance must be connected to a 240 volts 50 cycle AC supply by means of a three

pin socket, suitably earthed and should be protected by a 13 amp fuse in the plug.

The appliance is supplied with a standard 13 amp 3-pin plug fitted with a 13-amp fuse.

Should the fuse require replacement, it must be replaced with a fuse rated at 13 amp and

approved to BS1362.

If the mains plug is unsuitable for the socket outlet in your home or is removed for any

other reason, then the cut off plug should be disposed of safely, do not insert the cut off

plug into a mains outlet to prevent the hazard of electric shock. Remove the fuse before

disposal.

There is a danger of electric shock if the cut off plug is inserted into any 13-amp socket

outlet.

How to wire a 13 amp plug:

Important

The wires in the mains lead on this appliance are colored in accordance with the following

code:

Green and Yellow - Earth

Blue – Neutral

Brown – Live

As the colours may not correspond with the markings identifying the terminals in your plug

proceed as follows.

The green and yellow wire must be connected to the terminal in the plug which is marked

with the letter E or with the earth symbol or colored green and yellow.

The blue wire must be connected to the terminal marked N.

The brown wire must be connected to the terminal marked L.

You must make sure the mains cord is firmly secured under the cord clamp.

REFRIGERATOR SAFETY INFORMATION

Check that the voltage marked on the rating plate matches that of your local supply.

Failure to use the correct voltage will render the guarantee VOID and may cause damage to

the appliance.

The manufacturer accepts NO responsibility for using any other voltage than that marked on

the rating plate.

This appliance is intended for domestic use only; any other use may in validate the warranty

and might be dangerous.

This appliance is intended for indoor use only, do not use or store outdoors. This appliance

shall not be exposed to rain.

The mains plug shall be the main disconnect device and shall remain operable at all times.

A short power-supply cord is provided to reduce the risk of a tripping hazard.

To disconnect from the mains completely, turn the appliance OFF, then remove the plug from

wall outlet.

Do not immerse the appliance, its lead or plug in water or any other liquid.

Remove all food and unplug from the supply when not in use and before cleaning the

appliance.

If the mains lead becomes damaged, it must be replaced by the manufacturer, its service

agent or similarly qualified person with a specially prepared lead of the same type and rating

to avoid a hazard.

Do not operate the appliance with a damaged cord or plug or after the appliance malfunctions

or has been damaged in any way.

Do not let cord hang over edge of the surface, or touch hot surfaces.

Do not place the appliance on or near hot surfaces, or in direct sunlight.

Children must be supervised to make sure they do not swing on the door.

Accessible surfaces may get hot when in use, use handles and knobs at all times.

Always attach a plug to the appliance, and then plug it into the wall outlet and switch on.

If you are discarding an old appliance with a lock or catch fitted to the door, ensure that it is

left in a disabled condition to avoid the entrapment of young children when playing.

As old refrigeration ap pliances may contai n CFC’s whic h will dama ge the ozone layer, when

disposing of any refrigeration appliance please contact your lo cal waste disposal department

for advice on the correct method of disposal.

This appliance is not intended for use by persons(including children) with reduced physical,

sensory or mental capabilities, or lack of ex perience and knowledge, unless they have been

given supervision or instruction concerning us e of the appliance by a person responsible for

their safety.

Children should be supervised to ensure that they do not play on or near the appliance.

This appliance is for refrigerating food and making ice cubes.

REFRIGERANT

The refrigerating gas contained in the circuit of this appliance is Isobutane (R600a); it causes

a low level of pollution but is inflammable.

CAUTION:

Extreme caution must be used when moving the appliance.

WARNINGS:

Do not damage the refrigerant circuit.

Do not use sharp or pointed objects such as knives to remove ice when defrosting.

Do not use mechanical devices or other means to accelerate the defrosting process,

other than those recommended by the manufacturer.

Do not use electrical appliances inside the food storage compartments of the

appliance, unless they are of the type recommended by the manufacturer.

If the appliance is installed in a carpeted area, do not let the carpet block the

ventilation holes in the base of the unit, adjust the levelling feet after a few hours to

compensate for carpet movement.

Keep ventilation openings, in the appliance enclosure or the built in structure clear of

obstructions.

Installation

Position the appliance and allow to stand for two to three hours before it is turned on

for the first time to allow the system to settle. Do not position next to any heat source

e.g. cooker, boiler or in direct sunlight etc.

A clearance of 10 cm must be left between the sides of the appliance and any adjacent

cabinets or walls to allow for adequate air circulation. The appliance is not designed for

recessed installation (“building in”).

Install on a good firm level surface, and any unevenness of the floor should be

corrected prior to installation, slight unevenness can be overcome by adjusting the

front feet.

Do not keep your appliance in a room where the temperature is likely to fall below 16

degrees C (61 degrees F) at night and/or especially in winter, as it is designed to

operate in ambient temperatures between +16 and +32 degrees C (61 and 90 degrees

F). At lower temperatures the appliance may not operate, resulting in a reduction in

the storage life of the food.

Do not place the appliance near cookers or radiators or in direct sunlight, as this will cause

extra strain on the appliance’s functions.

If installed next to a source of heat such as a fridge, maintain the following minimum

clearances.

Choose a well-ventilated location with no less than 10cm clearance around the refrigerator.

Place the refrigerator in a location with a firm base in order to prevent vibration and excessive

noise.

Level the refrigerator by adjusting the two front feet.

Instructions for use

Remove all packing materials and check for damage, if the appliance is damaged, do

not use the appliance, contact the store where you purchased the appliance. Wash

the interior of the appliance using lukewarm water containing a little bicarbonate of

soda in the proportion of 1 teaspoon to 1.2 litres (2 pints) of water. Do not use

detergents or soaps as they may taint the food. After cleaning, dry all parts

thoroughly.

Temperature Control

The refrigerator is designed to maintain an internal storage temperature in the

refrigerator compartment between 0ćto + 8ć.

To enable adjustment of the temperature in the appliance it is fitted with an

adjustable thermostat located in the fridge compartment, which can be adjusted from

setting 1(warmest) to 7 (coldest). For normal working temperature it is recommended

to adjust the thermostat control to the position 4.5, after a few hours readjust the

thermostat to the desired temperature. There is also an off position “0”. Which

turns the refrigerator off. Note this dose not disconnect the appliance from the mains

supply. To do this you must remove the mains plug from the wall outlet.

To obtain a lower internal temperature turn the thermostat temperature control

clockwise to a higher number. To obtain a higher internal temperature turn the

thermostat control anticlockwise to a lower number. The internal temperature and

temperature control setting is dependent on a number of factors:

1. Varying ambient temperatures.

2. The number of times the appliance door is opened and how long the door remain

open.

3. The amount and temperature of the food and drink introduced into the appliance.

4. The weather conditions and time of year e.g. summer/winter.

5. The positioning of the appliance and an adequate air circulation to the sides and

back of the cabinet.

Never place hot or warm foods into the refrigerator or leave the doors open for longer

than necessary as this will raise the temperature and cause excessive amounts of

moisture thus increasing the amount of ice in the refrigerator compartment.

The Internal Light

The internal light will automatically switch ON and OFF whenever the refrigerator

door is opened or closed. To change the light bulb, see the section on changing the

light bulb.

Storage of fresh food in the refrigerator

Food should always be covered tightly with foil, plastic film, placed in bags or

stored in airtight containers. This will prevent food from dehydrating and prevent

the strong smell of some foods transferring to milder ones.

To store raw meat wrap in polythene bags or airtight containers and place on

the lowest shelf.

Do not allow raw meat to come into contact with cooked foods. For safety, only

store raw meat for two or three days. Fruit and vegetables should be thoroughly

cleaned and placed in the crisper drawer.

Milk and other liquids should be sealed with lids and placed in the bottle shelf

on the door.

Store frozen food

When using the freezer for the first time or after defrosting, turn the thermostat

temperature control to setting 7 for at least two hours before introducing the

food to be stored, then adjust to your preferred setting.

All frozen food products you purchase should be placed in the freezer as soon

as possible to avoid the frozen food from defrosting.

Storage recommendations printed on the packaging of frozen food by the

manufactures should always be followed.

Freezing fresh food (Freezer)

Ensure that your freezing operations are carried out under the most hygienic

conditions, as freezing alone does not sterilise the food. Never put hot or even

warm foodstuffs into the freezer. Prior to storing the food, pack it in plastic bags,

aluminum foil or freezer containers and place into the freezer without putting

them in contact with food that has already been frozen.

See the technical data sheet at the rear of this booklet for the maximum

permissible amount in kilograms of fresh food that can be frozen in any 24-hour

period with a room temperature of 25℃. Never freeze more than the

maximum permissible for a given 24 hours period.

Note: There are load limit lines as shown in right photo in the freezer

compartment. Never put food outside the load lines where the

desired temperature can not be reached.

Making ice cubes

Pour water into the ice cube tray until it is two thirds full and place into the

freezer. Ice cubes will form in approximately 2 to 3 hours. The ice cubes can be

easily removed by twisting the ice cube tray or running under cold water for a

short time.

Refrigerator defrost process

The refrigerator defrosting process is carried out automatically every time the

compressor stops.

The defrost water drains from the cabinet into a tray placed on the top of the

compressor to the rear of the unit where it evaporates.

Freezer defrost process

Small amounts of frost will accumulate inside the free er depending upon the

length of time during which the door is left open or the amount of moisture

introduced.

It is essential to ensure that no frost or ice is allowed to form at places where it

will affect the close fitting of the door seal. This might allow air to penetrate the

cabinet, thus encouraging continuous running of the compressor.

Thin frost formation is quite soft and can be removed with a brush or plastic

scraper. Do not use metal or sharp scrapers, mechanical devices or other

means to accelerate the defrosting process. Remove all dislodged frost from the

cabinet floor.

For the removal of thin frost it is not necessary to switch off the appliance.

For the removal of heavy ice deposits disconnect the appliance from the mains

supply and empty the contents into cardboard boxes and wrap in thick blankets

or layers of paper to keep them cold. Defrosting will be most effective if carried

out when the free er is empty, and it should be carried out as quickly as

possible.

An increase in temperature of fro en food packages during defrosting will

shorten the storage life. Provided that the contents are well wrapped and placed

in a cool area, they should keep for several hours.

Examine the contents when replacing them in the free er and if some of the

packages have thawed out it should be eaten within 24hours or be cooked and

refro en.

After defrosting has finished clean the inside with a solution of warm water with

a little bicarbonate of soda and then dry thoroughly. Wash all removable parts in

the same way and reassemble.

Reconnect the appliance to the mains supply and leave for 2 to 3 hours on

setting number 7 before introducing the food back into the free er and setting

the thermostat to your normal setting.

Cleaning and maintenance

Before any cleaning or maintenance is carried out you must disconnect the

appliance from the mains supply by removing the plug, never remove the plug

by pulling on the mains cord. Remove the plug by pulling on the plug itself.

It is recommended that when cleaning the appliance, both the inside and

outside, can be cleaned using warm water and a little bicarbonate of soda. Use

1 teaspoon to 1.2 litres of water.

If the appliance is not to be used for a long period of time then it is

recommended to remove all the food stuff, clean the inside of the appliance and

leave the door open to allow the air to circulate thus avoiding unpleasant odors.

Changing the light bulb

Note: The light bulb is not covered by the warranty.

1. Before carrying out the bulb replacement always switch

off and disconnect the electrical supply.

2. Use a small screwdriver to remove the screw holding the lamp cover onto the

thermostat housing.

3. Gently prise outwards until the cover releases.

4. Remove the old bulb by unscrewing in an anti-clockwise direction.

5. Replace with a new bulb (E14 10W) by screwing it in a clockwise direction making

sure that it is secure in the lamp holder.

6. Replace the lamp cover and re-connect your Refrigerator to the electrical supply

and switch on.

Power Failure

If there is a power failure for a short time less than 8hrs keep the door closed

Frozen food should not be affected if the failure lasts for less than 8hrs.

Extra protection can be given by covering the appliance with two or three thick

blankets.

If a long power failure is anticipated, try to get the foodstuff into another appliance or

cold store, if possible.

If the power cut is longer than 8hrs then check the content of the freezer.

If the food has defrosted, cook and refreeze the food or it should be eaten

immediately.

Never refreeze food that has been defrosted.

If the appliance is not operating correctly:

Please check the following points.

Is there a power failure? (Check by turning on a house light)

Has the fuse blown or has the circuit breaker tripped?

Has the door been closed correctly?

Check the thermostat has been set correctly.

Check the mains plug is seated in the wall socket correctly and the socket switch is

on.

Check the power outlet is working, Try another appliance.

Is the room temperature too cold or too hot? (working temperature range 16℃to

32℃)

REVERSING THE DOORS

Reversing the doors may make installation more convenient.

zEnsure that the appliance is unplugged and empty.

zWe recommend that you have someone to assist you.

Tools required:

zPhillips style screwdriver

zFlat bladed screwdriver

Note: to take the lower hinge off it is necessary to tilt the appliance backward. You

should rest the refrigerator on something solid.

DO NOT lay the appliance completely flat as this may damage the refrigerating

system.

1. Remove the four screws and then remove the top cover.

2. Remove the screws for upper hinge, and then remove the upper hinge, after that

remove the upper door.

3. Remove the middle hinge and then remove the lower door.

4. Remove the lower hinge and adjustable foot, and then re-fit them on the opposite

sides separately.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Proline Kühlschrank Handbücher

Proline

Proline PL115ABB Bedienungsanleitung

Proline

Proline UFZ167 Bedienungsanleitung

Proline

Proline PLF242L Bedienungsanleitung

Proline

Proline PLC246WDSL Bedienungsanleitung

Proline

Proline PLC316NFIX Bedienungsanleitung

Proline

Proline PF200W Bedienungsanleitung

Proline

Proline TTL 120 P Bedienungsanleitung

Proline

Proline PLI136G-E Benutzerhandbuch

Proline

Proline PLC 282 WH Bedienungsanleitung

Proline

Proline TTR 92 Bedienungsanleitung

Proline

Proline UFZ163NFWH Bedienungsanleitung

Proline

Proline PF90WA GL Bedienungsanleitung

Proline

Proline PLF225A-U Bedienungsanleitung

Proline

Proline TFP120A Bedienungsanleitung

Proline

Proline TTR200DP Bedienungsanleitung

Proline

Proline DD415 WH Bedienungsanleitung

Proline

Proline PMF70A Bedienungsanleitung

Proline

Proline TTR905 Bedienungsanleitung

Proline

Proline PLC163WH Bedienungsanleitung

Proline

Proline PLC 242 Bedienungsanleitung

Proline

Proline PRI 190-F-2-LED Bedienungsanleitung

Proline

Proline PLCD 330 WD SS Bedienungsanleitung

Proline

Proline DD253NFSL Bedienungsanleitung

Proline

Proline PLC150W Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung