Proluxe Vantage SL SL1577 Bedienungsanleitung
Operations Manual
Vantage SL - Split Lid Grill
Model #: SL1577
WWW.PROLUXE.COM
Version: 122820
Congratulations on your selection of
the Vantage SL Compact Split Lid
Grill. Proluxe is a leading
manufacturer of food preparation
and cooking equipment designed for
the most demanding commercial
kitchens. Proluxe equipment is a
result of the highest quality
engineering and time-tested design.
This manual includes installation,
operation, and maintenance
procedures for your new split lid
grill. Please read this manual
carefully and keep it with your
machine for proper operation and
lasting service.
Electrical:
120V/50-60Hz/220W/18.3 Amps
1 phase
Also available; specify when ordering:
●Voltage: 120/208/220
●Amps: 18.3/10
●Watts: 2200/2200/2800
Includes: 72” cord and 6-30P NEMA
approved plug.
Controlled heating zones: 3
Shipping Weight:
78lbs. (35kg)
G E T T I N G S T A R T E D
Please read carefully before attempting to
use this appliance.
1. Place in location where it will be used
allowing for clearances per the
dimensions indicated. Allow 2”
minimum clearance between
adjacent equipment and/or wall
areas.
2. Plug into proper 3 prong wall outlet.
If other appliances are connected to
the same circuit make sure the total
load does not exceed a maximum
ampacity of the circuit. Electrical
information is as follows:
3. Press the power button, the green
light above will illuminate when
powered on. The display flashes and
shows left preset timer during
warm-up. Pre-heat time will be 40-50
minutes. When the set point is
reached, the display stops flashing
and beeps 3 times.
4. Simply place product on either side of
the grill, close lid and press the
desired preset time cycle 10 or 20
seconds. After the time cycle is
finished press it again to reset the
time cycle.
1
I N T E R N A T I O N A L S Y M B O L S
Symboles internationaux
Power Off
éteindre
Power On
allumer
Hot Surface
surface chaude
Risk of Electrical Shock
Risque de choc électrique
Protective Earth Terminal
Borne de terre de protection
Caution - Warning
chaud - avertissement
S A F E T Y S U M M A R Y
Warning
To reduce the risk of electrical shock, do not
remove or open cover. No user-serviceable
parts inside. Refer servicing to qualified
personnel.
Avertissement
Pour réduire le risque de choc électrique, ne pas
retirer ou couvercle ouvert Aucune pièce
réparable par l’utillsateur, reportez-vous à du
personnel qualifié.
Warning
In case of power cord damage, do not
attempt to repair or replace the power cord.
Please contact the manufacturer or the local
distributor.
Avertissement
Pour une protection continue contre l’incendie
et de choc électrique, remplacer avec le même
type et calibre du fusible. Mis fusible
supplémentaire nominale max 3A, 120 Vac.
Warning
For continued protection against fire and
electric shock, replace with the same type
and rating fuse. Listed Supplemental Fuse
rated max 3A, 120Vac.
2
Avertissement
Pour une protection continue contre l’incendie
et de choc électrique, remplacer avec le même
type et calibre du fusible. Mis fusible
supplémentaire nominale max 3A, 120 Vac.
Caution Hot
Avoid touching hot surfaces while operating
the machine.
Attention à chaud
Évitez de toucher les surfaces chaudes lorsque
vous utilisez la machine.
Caution
When servicing or cleaning the machine,
make sure that the power cord is removed
from the wall socket.
During normal operation, the base of the
machine must be installed or placed above
the wall socket.
Avertissement
Lors de l'entretien ou du nettoyage de la
machine, assurez-vous que le cordon
d'alimentation est débranché de la prise murale.
T E M P E R A T U R E/T I M E R
S E T T I N G S
How to Find Set Temperature
To find the temperature of upper platens:
Press and hold the TEMP button and the
arrow up (↑) button at the same time.
To find the temperature of bottom platens:
Press and hold the TEMP button and the
arrow down (↓) button at the same time.
Adjusting the Set Temperature
1. Press and hold the TEMP button and
the arrow up (↑) button at the same
time for 15 seconds.
2. The current temperature with display
on the right digital display screen
only.
3. Using the up (↑) and down (↓) adjust
the temperature to your desired
setting.
4. Once your desired temperature is
set, push the TEMP button to return.
Adjusting the Set Time
1. Press the TEMP button first and then
select the desired timer button and
hold for 5 seconds.
2. The current temperature with display
on the right digital display screen
only.
3. Using the up (↑) and down (↓) adjust
the timer to your desired setting.
4. Once your desired temperature is
set, push the TEMP button to return.
Note: When adjusting the timer settings, the
right set of buttons control the left side.
Your left side timer will automatically set to
your right control settings. If you desire a
separate left timer you can manually adjust
3
the left side timer without affecting the right
timer.
C L E A N C Y C L E
Start Cycle
To start a clean cycle, push CLEAN button
once so the CLEAN LED light is turned on. All
preset LED’s are turned off, and the
temperature set point is changed to the clean
set point of 275°F. This also initiates the cool
down to clean set point condition as well the
display starts flashing until the clean set
point is reached.
Stop Cycle
To stop the clean cycle, simply press the
CLEAN button once to deactivate the clean
cycle. The CLEAN LED is turned off, the
preset LED’s are restored, the temperature
set point is changed to the main set point.
Again, the warm-up condition is initiated and
the display flashes until the cook set point is
reached.
Change Clean Temp
275°F is the factory default temp for the
CLEAN cycle. To change the CLEAN cycle
temp, simultaneously hold down the TEMP
and CLEAN buttons for 15 seconds. The
current temp setting will display on the right
digital display only. Using the up or down
arrows to adjust to the desired temp.
P R E V E N T A T I V E
M A I N T E N A N C E
Proluxe machines are relatively maintenance
free. For a long lifespan, the following
preventative maintenance should be
followed:
Daily Care:
1. Platens: Turn your machine off and allow
to cool down before attempting to clean.
These platens should only be cleaned with
mild soap and warm water then wiped off
with a clean, soft cloth or soft sponge.
2. Exterior surfaces: Wipe daily with mild
soap and warm water.
DO NOT use ice or cold water to cool the
unit down. This can cause platens to warp.
Service Problems:
Contact our factory at (800) 624-6717 (U.S.
only) or approved service agency. When
contacting the factory for information, parts
or service instructions, please provide the
serial number of the machine be provided.
This number can be found on the serial plate
located on the rear of the machine.
4
Vantage SL Troubleshoot Guide - Model #: SL1577
5
Problem
Cause
Action
Ref #
Power button on
digital controller face
is depressed but
doesn’t turn on.
1. Power cord is not plugged in.
2. Circuit breaker is tripped off in the
site's breaker box.
3. Transformer has taken an
electrical surge and is damaged.
4. Check voltage on the secondary
side of the Transformer. If you read
12VDC then you are receiving
voltage to the controller.
5. Possible blown fuse.
1. Plug the power cord into wall
receptacle and power button.
2. Reset circuit breaker that the
grill is plugged into. Depress
Power Button to turn on.
3. Replace Transformer after you
check secondary side of
transformer. If working properly,
you should receive 12vdc.
4. Replace controller. Controller
should be on once the power
button is depressed.
5. Replace fuse.
----
-----
18
A8
98
Digital controller's
LED's are scrambled
or randomly erratic.
If when turning on,
the display will first
go to segment check
1. Possibly a component on the
Digital controller is damaged.
2. Control needs to reset.
1. Replace digital controller.
2. While unit is on unplug unit,
wait for 1 min. Then plug machine
on again and depress the power
button.
A8
----
Digital controller is
constantly beeping.
No heat on either on
left, right, upper, or
lower platen.
Sensor in one of two zones lost it's
continuity. Depress TEMP. While
depressing TEMP depress either up
or down arrow to locate error
message PROB (zone 1, lower
platen, zone 2 left upper platen, zone
3, right upper platen.) If occurred
when depressing the up arrow
indicates either the left or right
platen has the open sensor or
Probe.
Disconnect probe and check for
continuity (by using Ohm Meter)
and replace. Do not cut and splice
new sensor. Install new 2000
ohm RTD sensor to underside of
the platen and reconnect to
controller. Upper left and right
sensor for replacement on upper
platens, lower platen sensor for
replacement for lower platen.
22
46
Digital display shows
Sensor lost it's continuity as shown
Disconnect prob that is open (no
41
6
PROB. No heat on
any platen.
on a muti-meter.
continuity as shown on a multi-
meter. Must replace sensor
(RTD). Do not cut and splice new
sensor. Install new 2000 ohm
RTD sensor to under side of heat
platen and reconnect to the
controller.
Digital controller
beeping and is
overheating.
The mechanical relay on the switched
side is not opening to regulate
temperature. Hold TEMP button
then depress either the down or up
arrow (zone 1, lower platen, zone 2,
left upper platen and zone 3, right
upper platen.) RLY will display on
problem zone indicating the damage.
Replace the mechanical relay.
15
Either platen is not
heating but the
digital controller is
on and appears to be
functioning.
If the mechanical relay(s) on the coil
side are receiving 12vdc indicates the
controller is functioning properly. If
there is no voltage on the switching
side of the relay to the heaters, the
relay is not working properly.
Replace the mechanical relay.
15
Beeper is not
functioning.
Beeper has failed.
Replace control board.
A8
One of the three
heater platens not
close to set point.
The offset function in the controller's
setting needs to be adjusted to
achieve proper shade of toast.
Call (800) 624-6717 for
instructions.
----
One heating zone is
not reaching setpoint
and another heater is
overheating.
Sensors maybe crossed.
Make sure each sensor is
connected to its prospective
position on the terminal block
and back to the controller.
----
Setpoint is reached
but slightly off in
temperature.
Offset may need to be calibrated and
adjusted.
Call (800) 624-6717 for
instructions.
----
Heater platen is
overheating.
1. The mechanical Relay may be
stuck in the closed position (zone 1,
lower platen #1 labeled on this relay,
zone 2, left upper and zone 3, right
upper).
2. If you are receiving 12vdc on the
coil of the relay, the controller is
properly functioning.
Use an Ohm meter for a
continuity check must check at
the cold pins of the heater (where
the heater wire is brazed at
the cold pin. This will eliminate
any other failure before the
heater element validating the loss
off continuity at the source the
heater element.
15
7
Upper heater not
coming down parallel
to the lower platen.
Parallel lever not attached either in
the rear out on the upper heater
platen. Check to see if parallel leveler
is connected on both sides. The
retaining clip attached to pin may
have come off.
Reconnect the pin and the
retaining E-Clip.
25
Upper platen falling
down or lost
tension.
The springs have lost some
tension.
Remove rear panel and adjust the
retaining collars on shaft by
winding the spring tighter. There
are multiple set screws that need
to be loosened in order to wind
the spring tighter. Once proper
tension is achieved, tighten all set
screws to prevent tension loss.
----
8
9
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Proluxe Grill Handbücher
Proluxe
Proluxe TACO BELL Vantage SL Compact Bedienungsanleitung
Proluxe
Proluxe Edge Plus Bedienungsanleitung
Proluxe
Proluxe CSD1212 Bedienungsanleitung
Proluxe
Proluxe Edge SE Bedienungsanleitung
Proluxe
Proluxe SL1577 Bedienungsanleitung
Proluxe
Proluxe SL1577PHC Bedienungsanleitung
Proluxe
Proluxe Tortillapro Pancheros DP2000BPP Bedienungsanleitung
Proluxe
Proluxe Vantage SL Bedienungsanleitung
Proluxe
Proluxe Progrill TW1520 Bedienungsanleitung
Proluxe
Proluxe SL1577HDA Bedienungsanleitung
Proluxe
Proluxe CSD1212 Bedienungsanleitung
Proluxe
Proluxe Progrill SL1577K Bedienungsanleitung
Proluxe
Proluxe Progrill SL1577W Bedienungsanleitung
Proluxe
Proluxe Progrill SL1577PHN Bedienungsanleitung
Proluxe
Proluxe ProGrill Taco Bell SL1266TB Bedienungsanleitung
Proluxe
Proluxe CSD1515 Bedienungsanleitung
Proluxe
Proluxe Progrill CS1500 Bedienungsanleitung
Proluxe
Proluxe Vantage SL Compact SL1266 Bedienungsanleitung
Proluxe
Proluxe DEL TACO SL1266DTA Bedienungsanleitung
Proluxe
Proluxe CS157TBA Bedienungsanleitung
