Promise Pegasus J4 Bedienungsanleitung

Quick Start Guide

•

Kurzanleitung •

Guide de démarrage rapide •

Guida rapida all'avvio •

Guía de inicio rápido •

Guia de consulta rápida •

Руководство по быстрому

•

началу работы

STRUČNÁ PŘÍRUČKA •

Gyors útmutato •

SKRÓCONA INSTRUKCJA OBSŁUGI •

クイシクスタートガイド

•

快速安裝手冊

•

快速安裝手冊

•

Quick Start Guide

•

Kurzanleitung •

Guide de démarrage rapide •

Guida rapida all'avvio •

Guía de inicio rápido •

Guia de consulta rápida •

Руководство по быстрому

•

началу работы

STRUČNÁ PŘÍRUČKA •

Gyors útmutato •

SKRÓCONA INSTRUKCJA OBSŁUGI •

クイシクスタートガイド

•

快速安裝手冊

•

快速安裝手冊

•

QUICK START GUIDE

SUMMARY OF SET UP PROCESS

This Quick Start Guide describes how to install four 2.5” storage drives in

the Pegasus J4*, then how to connect the power and Thunderbolt cable so the

device can be used and managed with a Thunderbolt equipped computer. The

installation steps in general are listed as follows:

STEP 1. INSTALL HARD DISKS (PAGE 3) *

STEP 2. CONNECT THE POWER (PAGE 6)

STEP 3. MAKE THE THUNDERBOLT CONNECTION (PAGE 7)

STEP 4. POWER ON THE J4 AND CHECK THE LEDS(PAGE 8)

STEP 5. CONFIGURE THE RAID ARRAY *

*Note

There are two versions of the Pegasus J4 available, one is

shipped without any physical storage drives. For this version,

it is necessary to install four 2.5” HDD or SSD into the empty

storage drive bays to use the device and then conﬁgure a

ﬁle system on the drives. The other version is shipped with

drives installed and ready to use.

INTHE PACKAGE

The Pegasus J4 package includes the following items:

* Pegasus J4

* Power cord, 1.5m

* Quick Start Guide

Follow the instructions for your version of the J4. One version has storage

drives installed and conﬁgured; another version requires the user to install

and conﬁgure 2.5” SATA storage drives.

Important

The Pegasus J4 requires a Thunderbolt cable (sold separately)

for connection to the host computer.

I NSTALL HARD DISKS

If your J4 has drives installed, skip ahead to “Connect the power” on page

6. If your J4 does NOT have drives installed, ﬁrst install four storage drives

in the J4.

REMOVE HOUSING COVER

1. Make sure the J4 is

powered off, and that

no power cable or

Thunderbolt cables are

attached.

2. Turn the J4 upside

down and place it on

a clean, dry table,

or similar ﬂat stable

surface. Be careful not

to scratch the housing.

3. Use a small Phillips

screwdriver to remove

the ﬁve screws that

secure the top housing.

Caution

The electronic components within the Pegasus J4

enclosure are sensitive to damage from Electro-Static

Discharge (ESD). Observe appropriate precautions at all

times when handling the J4 and storage drives

4. Hold the loosened housing top in place and turn the J4 back to the

normal position (bottom facing down). Place it on the table a lift the

housing top so that it detaches completely from the J4 chassis. Four

empty storage drive bays should be visible.

5. Place a new storage drive into an empty bay with the contact edge

ready to receive the contacts in the drive bay and oriented so the top

side is facing up (the top has a label with speciﬁcations and other

information about the drive).

Empty storage drive bays in J4 - top view

6. With the drive in position, push with your ﬁngers on the edge opposite

the drive contacts until the drive is ﬁrmly seated in the drive bay.

7. Attach the anchor screw to secure the drive in place.

8. Repeat steps 5 and 6 for each remaining hard drive.

9. Replace the housing top into its proper positing.

10. Hold the unsecured housing in place and turn the J4 upside down

once more.

11. Replace the screws and snug them tight. The J4 is ready to be

connected to a computer and a power source.

Rep

lace

the

screws

and

nug

them

tig

onnected to a com

uter and a

ower source.

C ONNECT THE POWER

Insert the power cord into the power receptacle on the back of the Pegasus

J4. Plug the other end into a suitable power source such as a wall outlet or

power strip.

M AKE THE THUNDERBOLT CONNECTION

Connect a Thunderbolt cable to either of the Thunderbolt ports on the back

of the Pegasus J4, and connect the other end of the cable to a Thunderbolt

port on your computer. The unused Thunderbolt port on the J4 can be used to

connect to another J4 or a monitor.

Important

Make sure the Thunderbolt cable connector is oriented

properly to be inserted into the Thunderbolt port.

P OWER ON THE J4 AND CHECK THE LEDS

Once the Thunderbolt connection is established it will be detected

automatically and the J4 will power on. Check the LED indicators on the front

to verify that the device is functioning properly.

Status LED Thunderbolt

connectionLEDs DriveactivityLEDs

It takes about 30 seconds for the device to fully boot up. After booting, the

LEDs should display as described here:

• The Status LED lights blue

• The Connection LEDs light blue for any connected port

• The Drive LEDs light blue

Inhaltsverzeichnis

Sprachen:

Andere Promise Lagerung Handbücher

Promise

Promise Smartstor NS4600 Bedienungsanleitung

Promise

Promise VTrak J830s Bedienungsanleitung

Promise

Promise Vess A6600P Bedienungsanleitung

Promise

Promise E610f Bedienungsanleitung

Promise

Promise VTrak J5960 Bedienungsanleitung

Promise

Promise SMARTSTOR NS4300N Bedienungsanleitung

Promise

Promise SMARTSTOR NS4300N Bedienungsanleitung

Promise

Promise Vess A Series Bedienungsanleitung

Promise

Promise VTrak D5000 Series Bedienungsanleitung

Promise

Promise VTRAK M610p Bedienungsanleitung

Promise

Promise Vess R3600 Series Bedienungsanleitung

Promise

Promise VessRAID 1000f Series Bedienungsanleitung

Promise

Promise Pegasus3 R4 Bedienungsanleitung

Promise

Promise PEGASUS 2 R2+ Bedienungsanleitung

Promise

Promise Pegasus2 R2+ Bedienungsanleitung

Promise

Promise SmartStor DS4600 Bedienungsanleitung

Promise

Promise VSkyCube c10X Montageanleitung

Promise

Promise Vess A2600 Bedienungsanleitung

Promise

Promise E610f Bedienungsanleitung

Promise

Promise VTrak N1008 Bedienungsanleitung

Promise

Promise VTRAK J300S Bedienungsanleitung

Promise

Promise VessJBOD 1730 Bedienungsanleitung

Promise

Promise Pegasus2 R6 Bedienungsanleitung

Promise

Promise Vess A3340s Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung