PROPOINT 8819484 Bedienungsanleitung
V1.0 8819484
Please read and understand all instructions before use. Retain this
manual for future reference.
USER MANUAL
CARGO VAN
LADDER RACK
8819484 CARGO VAN LADDER RACK V1.0
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Capacity 500 lb
Width 6 in.
Length 56-3/8 to 76-13/16 in.
Height
14 3/8 in.
Material Steel
Colour/Finish Heavy Duty Black Powder Coat
Mounting Attach to van's roof gutter
Adjustment Range 56 to 77 in.
INTRODUCTION
The Cargo Van Ladder Rack holds up to 500 lb of cargo. The
rack design allow easy installation without drilling or damaging
your vehicle.
SAFETY
WARNING! Read and understand all instructions before using
this tool. The operator must follow basic precautions to reduce
the risk of personal injury and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or
inspection and maintenance instructions.
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this
manual. A notice is an alert that there is a possibility of property
damage, injury or death if certain instructions are not followed.
CARGO VAN
LADDER RACK
V1.0 CARGO VAN LADDER RACK 8819484
Visit www.princessauto.com for more information 3
DANGER! This notice indicates an immediate and specific
hazard that will result in severe personal injury or
death if the proper precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe
practice that could result in severe personal injury
or death if the proper precautions are not taken.
CAUTION! This notice indicates a potentially hazardous situation
that may result in minor or moderate injury if proper
practices are not taken.
NOTICE! This notice indicates that a specific hazard or unsafe
practice will result in equipment or property
damage, but not personal injury.
WORK AREA
1. Operate in a safe work environment. Keep your work area
clean, well-lit and free of distractions. Place lights so you
are not working in a shadow.
2. Keep anyone not wearing the appropriate safety
equipment away from the work area.
3. Store unused tools properly in a safe and dry location to
prevent rust or damage. Lock tools away and keep out of
the reach of children.
4. Avoid contact with electrical sources in your work as the
rack is not insulated and will transmit an electric shock that
may cause an injury.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by
the Canadian Standards Association (CSA) or American
National Standards Institute (ANSI).
8819484 CARGO VAN LADDER RACK V1.0
4 For technical questions call 1-800-665-8685
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and
side protection for the eyes. Eye protection equipment
should comply with CSA Z94.3-07 or ANSI Z87.1 standards
based on the type of work performed.
2. Wear gloves that provide protection based on the work
materials or to reduce the effects of tool vibration.
3. Wear protective clothing designed for the work
environment and tool.
4. Non-skid footwear is recommended to maintain footing
and balance in the work environment.
5. Wear steel toe footwear or steel toe caps to prevent a foot
injury from falling objects.
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work
environment to avoid personal injury or damage to tool.
1. Do not operate any tool when tired or under the influence
of drugs, alcohol or medications.
2. Avoid wearing clothes or jewelry that can become
entangled with the moving parts of a tool. Keep long hair
covered or bound.
3. Do not overreach when operating a tool. Proper footing and
balance enables better control in unexpected situations.
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence to the
tool safety rules. If you use this tool unsafely or incorrectly,
you can suffer serious personal injury.
1. Use the correct tool for the job. This tool was designed for a
specific function. Do not modify or alter this tool or use it for
an unintended purpose.
V1.0 CARGO VAN LADDER RACK 8819484
Visit www.princessauto.com for more information 5
2. Do not use the tool if any parts are damage broken or
misplaced. Repair or replace the parts.
3. Do not exceed the rack’s maximum capacity (see
Specifications).
4. Secure the load with straps to prevent unwanted movement
that can cause the load to slide, fall off the arm or vibrate.
5. Check all bolts and connections for tightness daily. Tighten
the bolts when necessary.
6. Avoid overloading the rack. Distribute the load evenly.
Overloading can make the vehicle top-heavy and may cause
a vehicle roll over during turns, stops or strong winds.
7. Be aware of the overall height of the load on the vehicle to
avoid striking low overhead structures.
8. Do not load the racks in a manner that will block or obscure
your view of the road or surroundings while driving.
9. Only load a vehicle on a firm, level surface capable of
sustaining the load. Never load the racks on a vehicle
resting on a sloped or soft surface, as the load may shift or
fall and injure you or a bystander.
10. Only use manufacturer accessories with the rack. Using an
accessory not designed for the rack may fail and injury you
or a bystander.
UNPACKING
WARNING! Do not operate the tool if any part is missing.
Replace the missing part before operating. Failure to do so
could result in a malfunction and personal injury.
Remove the parts and accessories from the packaging and
inspect for damage. Make sure that all items in the parts list
are included.
8819484 CARGO VAN LADDER RACK V1.0
6 For technical questions call 1-800-665-8685
ASSEMBLY & INSTALLATION
Numbered references in parenthesis (#1) refer to the included
Parts List.
1. Select one of the four mounting holes (#4) in the upright
(#1) that will clear the vehicle roof.
2. Slide a lock washer (#11) and SAE flat washer (#8) over an
M12x25 hex bolt (#7). Insert the bolt through the selected
mounting hole. The gutter clamp (#5) faces outward.
Repeat with the other upright.
3. Screw the short cross brace (#3) onto one upright and the
long cross brace (#2) onto the other upright. Secure both
hex bolts with a wrench.
4. Repeat steps 2 and 3 to assemble the other rack set.
5. Slide each short cross brace into a long cross brace. Screw an
M10x15 Allen head set screw into the long cross brace just
tight enough to hold the braces together. You may need to
loosen it to adjust the rack during installation.
6. The gutter clamp on all uprights is pre-assembled.
INSTALL ON THE VEHICLE
1. Loosen both M6x35 hex bolts (#6) so the gutter clamps are
easily moved.
2. Place the rear part of the upright in the rain gutter.
3. Loosen the set screw in the long cross brace.
4. Adjust the cross brace from the other side of the vehicle
until the second upright fits into the rain gutter. Tighten the
M6x35 hex bolt until the gutter clamp is locked under the
vehicle’s rain gutter.
5. Tighten the gutter clamp on the other side, then tighten
the set screw to secure the cross braces.
6. Repeat Steps 1 to 5 with the second set of cross braces.
V1.0 CARGO VAN LADDER RACK 8819484
Visit www.princessauto.com for more information 7
CARE & MAINTENANCE
1. Maintain the tool with care. A tool in good condition is
efficient, easier to control and will have fewer problems.
2. Inspect the tool components periodically. Repair or replace
damaged or worn components. Only use identical
replacement parts when servicing.
WARNING! Only qualified service personnel should repair the
tool. An improperly repaired tool may present a hazard to the
user and/or others.
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does
not function properly or parts are missing. If unable to do so,
have a qualified technician service the tool.
8819484 CARGO VAN LADDER RACK V1.0
8 For technical questions call 1-800-665-8685
PARTS BREAKDOWN
PARTS LIST
# DESCRIPTION QTY
1 Upright 4
2
Long Cross Brace
2
3 Short Cross Brace 2
4 Mounting Holes ---
5
Gutter Clamp
4
6 Hex Bolt M6x35 4
7 Hex Bolt M12x25 4
8 SAE Flat Washer M12 4
9
SAE Flat Washer M6
4
10 Allen Head Set Screw
M10x15
2
11 Lock Washer M12 4
12 Lock Washer M6 4
V1,0 8819484
Vous devez lire et comprendre toutes les instructions avant d'utiliser
l'appareil. Conservez ce manuel afin de pouvoir le consulter plus tard.
MANUEL D'UTILISATEUR
SUPPORT D’ÉCHELLE
POUR FOURGONNETTE
UTILITAIRE
8819484 SUPPORT D’ÉCHELLE POUR FOURGONNETTE UTILITAIRE V1,0
2 En cas de questions techniques, appelez le 1-800-665-8685
SPÉCIFICATIONS
Capacité 500 lb
Largeur
6 po
Longueur 56 3/8 à 76 13/16 po
Hauteur
14 3/8 po
Matériau Acier
Couleur/fini Revêtement en poudre noir robuste
Montage Se fixe à la gouttière de toit de la fourgonnette
Plage de réglage
56 à 77 po
INTRODUCTION
Le support d’échelle pour fourgonnette utilitaire peut soutenir
une charge jusqu’à 500 lb. La conception du support permet
de l’installer facilement sans percer de trou ou endommager
votre véhicule.
SÉCURITÉ
AVERTISSEMENT ! Veuillez lire et comprendre toutes les
instructions avant d'utiliser cet outil. L'utilisateur doit respecter
les précautions de base lorsqu'il utilise cet outil afin de réduire le
risque de blessure ou de dommage à l'équipement.
Conservez ce manuel qui contient les avertissements de
sécurité, les précautions, les instructions de fonctionnement ou
d'inspection et d'entretien.
SUPPORT D’ÉCHELLE
POUR FOURGONNETTE
Inhaltsverzeichnis
Sprachen:
Andere PROPOINT Autozubehör Handbücher
