Prorack K427 Bedienungsanleitung
K427
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 4 x 4 x 2
x 1 x 1 x 2 x 2
Revision No: 5C 1
Fitting Kit K427
MAX kgs (lbs)
W/P WHD
Peugeot
206 , 3dr Hatch 98-06 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
206 , 3dr Hatch 98-06 ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
206 , 3dr Hatch 98-06 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
206 , 3dr Hatch 98-06 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
2
Fitting Kit EN
K427
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
3
Fitting Kit EN
K427
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment.
●Ensure each end of the crossbar is
adjusted equally.
4
Fitting Kit EN
K427
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
5
Fitting Kit EN
K427
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 545A
B = 546B
C = 547B
●NOTE: REAR CROSSBAR ONLY
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●The rear crossbar secures directly to the
edge of the roof above the rear window.
●Fit rubber pad (supplied with crossbar) to
foot.
●Make sure the pad fits into the holes
underneath the foot.
●Repeat for all legs.
6
Fitting Kit EN
K427
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●NOTE: FRONT CROSSBAR ONLY
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●To install the front crossbar, pull back top
rubber door seal. Locate threaded inserts
under black spots above the front doors.
●Put front clamp in place. Refit the clamp
block over clamp. Refit locking screw,
ensuring end of screw inserts in the hole on
the clamp.
7
Fitting Kit EN
K427
●Fit a fibre washer on each capscrew and
attach front clamps to the vehicle body.
●Refit rubber seal over the clamp.
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 5 Nm (3.7 ft lb).
●Repeat for all four positions.
8
Fitting Kit EN
K427
●Progressively tighten the clamp block
locking screws alternating from one side of
the vehicle to the other to tension evenly.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
9
Fitting Kit EN
K427
Maintenance
●Clean the car roof and surfaces of the
product that will be in contact with the car
roof.
●Follow the fitting instructions for fitting the
product to your vehicle. Make sure all steps
are carried out in order.
●Set crossbars a minimum distance of
700mm (27 1/2") apart where no other
distance is specified in the fitting
instructions. This is especially important
when carrying long loads.
●Check unit is securely attached whenever
you refit it to the vehicle. If the unit feels
loose, refer to the fitting instructions and
readjust.
●Some glass/panoramic roofs and radio
antennae may not be able to be used when
the product is fitted.
●Do not modify this product.
●Refer to the maximum permitted load
capacity specified in the fitting instructions.
Do not exceed the vehicle manufacturers
roof load rating if it is lower than the
maximum load capacity specified in the
fitting instructions.
●Loads should not overhang the sides of the
product and be evenly distributed with the
lowest possible centre of gravity.
●Long loads should be secured with non-
elastic straps to the front and rear of the
vehicle.
●Objects with pointed ends (e.g. ski poles)
should be carried with the pointed ends to
the rear of the vehicle.
●Remove all loose or removable objects
from the load prior to loading.
●Make sure all loads are securely fastened
with non-elastic straps. Check regularly
during longer journeys.
●A loaded roof rack system can alter the
performance of your vehicle. Be especially
aware of the effects of side winds,
changing of direction, and braking
performance. Avoid rapid acceleration and
deceleration. Drive carefully.
●Note that the total height of the vehicle
increases when upright loads are carried.
●Products should be locked during transport
if they have locks fitted.
10
Inhaltsverzeichnis
Andere Prorack Autozubehör Handbücher
Prorack
Prorack K1062 Bedienungsanleitung
Prorack
Prorack K560 Bedienungsanleitung
Prorack
Prorack K351 Bedienungs- und Installationshandbuch
Prorack
Prorack K387 Bedienungsanleitung
Prorack
Prorack K890 Bedienungsanleitung
Prorack
Prorack K541 Bedienungsanleitung
Prorack
Prorack K580 Bedienungs- und Installationshandbuch
Prorack
Prorack K774 Bedienungsanleitung
Prorack
Prorack K1007 Bedienungsanleitung
Prorack
Prorack K174 Bedienungsanleitung
Prorack
Prorack K639 Bedienungsanleitung
Prorack
Prorack K436 Bedienungsanleitung
Prorack
Prorack P16 Bedienungsanleitung
Prorack
Prorack K069 Bedienungsanleitung
Prorack
Prorack K571 Installationsanleitung
Prorack
Prorack S27 Bedienungsanleitung
Prorack
Prorack K945 Bedienungsanleitung
Prorack
Prorack K075 Bedienungsanleitung
Prorack
Prorack K407 Bedienungsanleitung
Prorack
Prorack K346 Bedienungsanleitung
