Prorack K528 Bedienungsanleitung
K528
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 8 x 4 x 8
x 4 x 4 x 4 x 8
x 4
Revision No: 2C 1
Fitting Kit K528
MAX kgs (lbs)
W/P WHD
Nissan
Stagea M35, 5dr Wagon 01-07 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Stagea M35, 5dr Wagon 01-07 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
2
Fitting Kit EN
K528
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
3
Fitting Kit EN
K528
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Ensure each end of the crossbar is
adjusted equally.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment.
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Attaches to factory-fitted mounting points
4
Fitting Kit EN
K528
●Tighten adjusting screw to 5 Nm (3.7 ft lb).
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Remove both pins from each leg. Use
tapered end of spanner located inside left
hand cover to assist.
5
Fitting Kit EN
K528
●Detach foot from leg. Store loose parts in a
safe place.
●Repeat for all legs.
●Assemble metal loadplate and rubber pad
from the fitting kit.
●Repeat for all four items.
●Assemble metal loadplate into leg. Ensure
loadplate interlocks with the leg.
6
Fitting Kit EN
K528
●Using short capscrew and washer, secure
assembly onto leg (use Hex Screwdriver
supplied with crossbar to assist)
●Repeat for all legs.
Fitment
●Open or remove fixed-point covers.
●Store items away in a safe place.
●Use fixed-point rear mounting hole.
●Apply protective strip as shown.
Trim if required.
7
Fitting Kit EN
K528
●Fit cover plates over opening.
●Slot in cover should line up over rear fixed
point thread.
●Leave loose until both sides have had the
screw fitted.
●Fit the M6 socket head screw and M6
washer.
●Tighten foot and cover plate down using
the Hex Key.
8
Fitting Kit EN
K528
●Ensure that the cover plate and foot sit
firmly on the roof.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
9
Fitting Kit EN
K528
Maintenance
●Clean the car roof and surfaces of the
product that will be in contact with the car
roof.
●Follow the fitting instructions for fitting the
product to your vehicle. Make sure all steps
are carried out in order.
●Set crossbars a minimum distance of
700mm (27 1/2") apart where no other
distance is specified in the fitting
instructions. This is especially important
when carrying long loads.
●Check unit is securely attached whenever
you refit it to the vehicle. If the unit feels
loose, refer to the fitting instructions and
readjust.
●Some glass/panoramic roofs and radio
antennae may not be able to be used when
the product is fitted.
●Do not modify this product.
●Refer to the maximum permitted load
capacity specified in the fitting instructions.
Do not exceed the vehicle manufacturers
roof load rating if it is lower than the
maximum load capacity specified in the
fitting instructions.
●Loads should not overhang the sides of the
product and be evenly distributed with the
lowest possible centre of gravity.
●Long loads should be secured with non-
elastic straps to the front and rear of the
vehicle.
●Objects with pointed ends (e.g. ski poles)
should be carried with the pointed ends to
the rear of the vehicle.
●Remove all loose or removable objects
from the load prior to loading.
●Make sure all loads are securely fastened
with non-elastic straps. Check regularly
during longer journeys.
●A loaded roof rack system can alter the
performance of your vehicle. Be especially
aware of the effects of side winds,
changing of direction, and braking
performance. Avoid rapid acceleration and
deceleration. Drive carefully.
●Note that the total height of the vehicle
increases when upright loads are carried.
●Products should be locked during transport
if they have locks fitted.
10
Inhaltsverzeichnis
Andere Prorack Autozubehör Handbücher
Prorack
Prorack K379 Bedienungsanleitung
Prorack
Prorack K376 Bedienungsanleitung
Prorack
Prorack K337 Bedienungsanleitung
Prorack
Prorack K442 Bedienungsanleitung
Prorack
Prorack K449 Bedienungsanleitung
Prorack
Prorack K1208 Bedienungsanleitung
Prorack
Prorack K1003 Bedienungsanleitung
Prorack
Prorack K621 Bedienungsanleitung
Prorack
Prorack K568 Bedienungsanleitung
Prorack
Prorack K560 Bedienungsanleitung
Prorack
Prorack K687 Bedienungsanleitung
Prorack
Prorack K925 Bedienungsanleitung
Prorack
Prorack K317 Bedienungsanleitung
Prorack
Prorack K774 Bedienungsanleitung
Prorack
Prorack K596 Bedienungsanleitung
Prorack
Prorack K757 Bedienungsanleitung
Prorack
Prorack K077 Bedienungsanleitung
Prorack
Prorack K657 Bedienungsanleitung
Prorack
Prorack K424 Bedienungsanleitung
Prorack
Prorack K375 Bedienungsanleitung
