Prorack PR3205 Bedienungsanleitung
Page 1 of 6
09-13-565-Rev2
Kit Contents
PR3205
Fuel Container Holder
First Time Installation
• Please read instructions carefully before installation.
• Check the contents of kit. Contact your Prorack dealer if any parts appear to be missing or damaged.
• Clean your roof racks and cargo tray prior to fitting the Fuel Container Holder.
Important Warning
• It is critical that all Prorack racks and accessories be properly and securely attached to your vehicle. Improper
attachment could result in an automobile accident, and could cause serious bodily injury or death to you or to others.
• You are responsible for securing the racks and accessories to your car, checking the attachments prior to use, and
periodically inspecting the products for adjustment, wear, and damage.
• If you do not understand all of the instructions and cautions, or if you have no mechanical experience and are not
thoroughly familiar with the installation procedures, you should have the product installed by a professional installer
such as a roof rack specialist.
Tools Required
• Allen Key (provided)
• 13 mm/16 mm Spanner
• 16 mm Socket + Socket Wrench (for dual side-by-side installation)
Item Component Qty
1 Fuel Container Holder 1
2 Ratchet & Short Webbing Strap 1
3 Long Webbing Strap 1
4 M6 Capscrew Button Head 4
5 M6 Washer 8
6 M6 Nylock Nut 4
7 M10 x 25 mm Set Screw 2
8 M10 Spring Washer 2
9 M10 Washer 2
10 M10 Spring Nut 2
11 M10 x 20 mm Set Screw 2
12 M10 T-Nut 2
13 M8 x 16 mm Set Screw 2
15 M8 Spring Washer 2
15 M8 Washer 2
16 M8 T-Slot Nut 2
17 Holder Mounting Bracket 2
18 4 mm Allen Key 1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Page 2 of 6
09-13-565-Rev2
Turn the fuel container holder upside down and fit both mounting brackets on to the long side of the holder.
1
Install to Standard Cargo Tray on Prorack HD, Tradesman and other Heavy Duty Crossbars
Position 2x M10 spring nuts into the crossbar
channel either side of tray slat where holder
will be positioned. Push spring nuts down into
crossbar channel and twist to lock into place.
Use the assembled holder from step 1 to ensure
spring nuts align with holes in brackets.
23Secure each mounting bracket on to the spring
nuts in the crossbar using 2x M10 x 25 mm
set screws, 2x M10 spring washers and 2x
M10 washers. Use a 16 mm spanner to tighten
screws to 4-5 Nm.
Ensure brackets are fitted on the inside of the holder and that the screw heads face inwards. Tighten
capscrews with Allen key to 4-5 Nm.
M6 Nylock Nut
M6 Washer
M6 x 16 mm Capscrew
Page 3 of 6
09-13-565-Rev2
Turn the fuel container holder upside down and fit both mounting brackets on to the long side of the holder.
1
23
Ensure brackets are fitted on the inside of the holder and that the screw heads face inwards. Tighten
capscrews with Allen key to 4-5 Nm.
M6 Nylock Nut
M6 Washer
M6 x 16 mm Capscrew
Install to Standard Cargo Tray on Prorack S-Wing and International T-Slot Crossbars
Push rubber infill down and slide 2x M10
T-nuts into the crossbar channel either side
of tray slat where holder will be positioned.
Use the assembled holder from step 1 to
ensure T-nuts align with holes in brackets.
Secure each mounting bracket on to the T-nuts
in the crossbar using 2x M10 x 20 mm set
screws, 2x M10 spring washers and 2x M10
washers. Use a 16 mm spanner to tighten
screws to 4-5 Nm.
Page 4 of 6
09-13-565-Rev2
12
Install to Cargo Tray with T-Slot Channels
Slide 2x M8 nuts into the T-slot of the tray. Position holder centrally over a crossbar in the
preferred position. Secure the fuel container
holder on to the M8 nuts in the T-slot using 2x
M8 x 16 mm set screws, 2 x M8 spring washers
and 2x M8 washers. Use a 13 mm spanner to
tighten screws to 4-5 Nm.
2
Securing the Fuel Container
Place the fuel container vertically into the
holder ensuring the filler cap is facing upwards
as shown.
Loop the ratchet through the handle in the
short strap around the crossbar on one side of
the holder and loop the long strap through its
handle around the crossbar on the other side of
the holder.
Secure the holder with the straps and ratchet
provided.
Ratchet is looped around crossbar and
through itself
Strap is looped around crossbar and
through itself
1
Page 5 of 6
09-13-565-Rev2
Installing Dual Fuel Container Holders
For this configuration, one mounting bracket will be required to sit on the other as shown. Adjust position of the
mounting brackets to ensure both holders sit flat on the cargo tray.
Using an M10 x 25 mm set screw, an M10 spring washer and an M10 washer, assemble the two holders on
to the spring nut or T-nut in the crossbar channel. Use a 16 mm socket & socket wrench to tighten the set
screw to 4-5 Nm.
One mounting bracket
sitting on the other
Page 6 of 6
09-13-565-Rev2
Maintenance
• Check accessory is securely attached whenever you refit it to the vehicle. If the unit feels loose, refer to the fitting
instructions and readjust.
• Regularly check all fasteners. This includes all attached accessories and roof racks.
• If straps become contaminated with oil, fuel or acid remove with hot soapy water.
• If the ratchet mechanism becomes stiff in use, a small amount of lubrication applied to the moving parts will ease
operation.
Caution
• Ensure all loads are distributed evenly across the roof racks and are fastened securely.
• A loaded roof rack system can alter the performance of your vehicle. Be especially aware of the effects of side winds,
changing of direction, and braking performance. Avoid rapid acceleration and deceleration. Drive carefully.
• Make sure all loads are securely fastened with non-elastic straps. Check regularly during longer journeys.
• Never drive into a car wash with the roof rack system fitted.
• Do not exceed the vehicle manufacturer’s roof load rating. Total load equals weight of roof racks + accessories + cargo/
equipment.
• Ratcheting strap must not be used for lifting. Protect from abrasion and friction. Do not tie knots in the straps. Do not
use a damaged strap.
• 150 kg lashing capacity on the polypropylene webbing.
Prorack
17 Hinkler Court, Brendale
QLD 4500, Australia
Freephone
AU: 1800 143 548 www.prorack.com.au
NZ: 0800 4776 722 www.prorack.co.nz
Inhaltsverzeichnis
Andere Prorack Autozubehör Handbücher
Prorack
Prorack K042 Bedienungsanleitung
Prorack
Prorack K435 Bedienungs- und Installationshandbuch
Prorack
Prorack K769 Bedienungsanleitung
Prorack
Prorack K324 Bedienungsanleitung
Prorack
Prorack K431 Bedienungsanleitung
Prorack
Prorack K511 Bedienungsanleitung
Prorack
Prorack K1245 Bedienungsanleitung
Prorack
Prorack K596 Bedienungsanleitung
Prorack
Prorack K982 Bedienungs- und Installationshandbuch
Prorack
Prorack K533 Bedienungsanleitung
Prorack
Prorack K1221 Bedienungsanleitung
Prorack
Prorack K611 Bedienungsanleitung
Prorack
Prorack K757 Bedienungsanleitung
Prorack
Prorack K731 Bedienungsanleitung
Prorack
Prorack K1208 Bedienungsanleitung
Prorack
Prorack K143 Bedienungsanleitung
Prorack
Prorack K507 Bedienungsanleitung
Prorack
Prorack J-Cradle Bedienungsanleitung
Prorack
Prorack K661 Bedienungs- und Installationshandbuch
Prorack
Prorack K327 Bedienungsanleitung
